From: Corrado Cappello <Corrado.Cappello@italtel.it>
To: linux-kernel@vger.kernel.org
Cc: Daniele.Garbagnati@italtel.it, Gianmarco.Vocino@italtel.it,
Corrado.Cappello@italtel.it, cappelc@hotmail.com
Subject: PROBLEM: restore file in tar from a magnetic tape device attached on SCSI
Date: Wed, 28 Aug 2002 12:37:00 +0200 [thread overview]
Message-ID: <3D6CA7CC.685FE47@imads2.milano.italtel.it> (raw)
[-- Attachment #1: Type: text/plain, Size: 227 bytes --]
--
+----------------------------------+
Corrado Cappello Italtel spa
TPD-SP-PE-U
E-Mail:corrado.cappello@italtel.it
Phone (+39.2)43888991
Fax (+39.2)43888705
Mobile (+39.2)43884212
+----------------------------------+
[-- Attachment #2: oopsFull.txt --]
[-- Type: text/plain, Size: 14284 bytes --]
Problem: restore file in archive file format from a magnetic tape device attached on SCSI BUS.
When i restore file by tar -xvf /dev/st0 and recorded on tape there is the following list:
-rw-r--r-- 1 cappelc cappelc 184854528 lug 26 16:06 cdimg.iso
the system panics.
/proc/version's output is:
Linux version 2.4.18 (kernelu@ic3sd04) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-87)) #5 ven lug 26 08:22:19 CEST 2002
ksymoops's output is:
ksymoops 2.4.0 on alpha 2.4.18. Options used
-v /boot/vmlinux-2.4.18 (specified)
-k /proc/ksyms (default)
-l /proc/modules (default)
-o /lib/modules/2.4.18/ (default)
-m /boot/System.map-2.4.18 (specified)
Unable to handle kernel paging request at virtual address 0000000000000230
swapper(0): Oops 1
pc = [<fffffc000043ef74>] ra = [<fffffc000043ef74>] ps = 0007 Not tainted
Using defaults from ksymoops -t elf64-alpha -a alpha
v0 = 0000000000000000 t0 = 0000000000000000 t1 = ffffffffffe20fe0
t2 = 0000000000000000 t3 = 0000000000000005 t4 = 000000000000002b
t5 = fffffffffffffc18 t6 = 000000000008e44d t7 = fffffc000056c000
s0 = 0000000000000000 s1 = fffffc0000e6e4c0 s2 = 0000000000000006
s3 = fffffc0000e6e400 s4 = fffffc00005d8dd8 s5 = 0000000000000006
s6 = 0000000000000000
a0 = fffffc0000f6e140 a1 = 0000000000000000 a2 = fffffc000056fed8
a3 = 0000000000000080 a4 = 0000000000000001 a5 = 0000000000000400
t8 = fffffc00005d9a80 t9 = 0000000000001fff t10= fffffffffffffffe
t11= 0000000000001fff pv = fffffc00003225d0 at = fffffc0000590080
gp = fffffc000061e1a0 sp = fffffc000056fdf8
Trace: fffffc000043ebac fffffc0000315954 fffffc0000316354 fffffc0000323954 fffffc
0000316988 fffffc0000310b38 fffffc00003122a0 fffffc0000327e70 fffffc0000312280 f
ffffc000035ee40 fffffc00003100a4 fffffc000031001c
Code: b26901d4 a0300000 443ff001 402075a1 e4200004 d3400049 <b0090230> c3e0
>>PC; fffffc000043ef74 <isp1020_intr_handler+3a4/4c0> <=====
Trace; fffffc000043ebac <do_isp1020_intr_handler+2c/50>
Trace; fffffc0000315954 <handle_IRQ_event+b4/130>
Trace; fffffc0000316354 <handle_irq+134/1d0>
Trace; fffffc0000323954 <dp264_srm_device_interrupt+34/50>
Trace; 0000000000fffffc Before first symbol
Code; fffffc000043ef5c <isp1020_intr_handler+38c/4c0>
0000000000000000 <_PC>:
Code; fffffc000043ef5c <isp1020_intr_handler+38c/4c0>
0: d4 01 69 b2 stl a3,468(s0)
Code; fffffc000043ef60 <isp1020_intr_handler+390/4c0>
4: 00 00 30 a0 ldl t0,0(a0)
Code; fffffc000043ef64 <isp1020_intr_handler+394/4c0>
8: 01 f0 3f 44 and t0,0xff,t0
Code; fffffc000043ef68 <isp1020_intr_handler+398/4c0>
c: a1 75 20 40 cmpeq t0,0x3,t0
Code; fffffc000043ef6c <isp1020_intr_handler+39c/4c0>
10: 04 00 20 e4 beq t0,24 <_PC+0x24> fffffc000043ef80 <isp1020_intr_handler+3b0/4c0>
Code; fffffc000043ef70 <isp1020_intr_handler+3a0/4c0>
14: 49 00 40 d3 bsr ra,13c <_PC+0x13c> fffffc000043f098 <isp1020_return_status+8/140>
Code; fffffc000043ef74 <isp1020_intr_handler+3a4/4c0> <=====
18: 30 02 09 b0 stl v0,560(s0) <=====
Code; fffffc000043ef78 <isp1020_intr_handler+3a8/4c0>
1c: e0 c3 00 00 call_pal 0xc3e0
Environment:
Software:
If some fields are empty or look unusual you may have an old version.
Compare to the current minimal requirements in Documentation/Changes.
Linux ic3sd04 2.4.18 #6 mer ago 28 08:54:02 CEST 2002 alpha unknown
Gnu C 2.96
Gnu make 3.79.1
binutils 2.10.91.0.2
util-linux 2.10s
mount 2.11e
modutils 2.4.2
e2fsprogs 1.19
PPP 2.4.0
isdn4k-utils 3.1pre1
Linux C Library 2.2.3
Dynamic linker (ldd) 2.2.3
Procps 2.0.7
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0
Modules Loaded autofs
Processor information:
cpu : Alpha
cpu model : EV6
cpu variation : 7
cpu revision : 0
cpu serial number :
system type : Tsunami
system variation : Webbrick
system revision : 0
system serial number : AY0
cycle frequency [Hz] : 462962962
timer frequency [Hz] : 1024.00
page size [bytes] : 8192
phys. address bits : 44
max. addr. space # : 255
BogoMIPS : 921.84
kernel unaligned acc : 0 (pc=0,va=0)
user unaligned acc : 0 (pc=0,va=0)
platform string : COMPAQ AlphaServer DS10 466 MHz
cpus detected : 1
Module information:
autofs 15392 1 (autoclean)
Loaded driver and hardware information:
00000000-01ffffff : PCI IO bus 0
00000000-0000001f : dma1
00000020-0000003f : pic1
00000040-0000005f : timer
00000060-0000006f : keyboard
00000070-00000080 : rtc
00000070-0000007f : rtc
000000a0-000000bf : pic2
000000c0-000000df : dma2
00000170-00000177 : ide1
000002f8-000002ff : serial(auto)
00000376-00000376 : ide1
000003f0-000003f5 : floppy
000003f7-000003f7 : floppy DIR
000003f8-000003ff : serial(auto)
00008000-000080ff : QLogic Corp. ISP1020
00008000-000080fe : qlogicisp
00008400-0000847f : Digital Equipment Corporation DECchip 21142/43
00008400-0000847f : tulip
00008480-000084ff : Digital Equipment Corporation DECchip 21142/43 (#2)
00008480-000084ff : tulip
00008800-0000887f : Digi International AccelePort Xr/J
00008880-0000888f : Acer Laboratories Inc. [ALi] M5229 IDE
00008890-0000889f : Acer Laboratories Inc. [ALi] M5229 IDE
000088a0-000088af : Acer Laboratories Inc. [ALi] M5229 IDE
000088a0-000088a7 : ide0
000088a8-000088af : ide1
000088b0-000088b3 : Acer Laboratories Inc. [ALi] M5229 IDE
000088b4-000088b7 : Acer Laboratories Inc. [ALi] M5229 IDE
00009000-0000907f : tulip
00009080-000090ff : tulip
00009400-0000947f : tulip
00009480-000094ff : tulip
00000000-ffffffff : PCI mem bus 0
09000000-097fffff : Texas Instruments TVP4020 [Permedia 2]
09800000-09ffffff : Texas Instruments TVP4020 [Permedia 2]
0a000000-0a3fffff : Digi International AccelePort Xr/J
0a400000-0a43ffff : Digital Equipment Corporation DECchip 21142/43
0a440000-0a47ffff : Digital Equipment Corporation DECchip 21142/43 (#2)
0a480000-0a49ffff : Texas Instruments TVP4020 [Permedia 2]
0a4a0000-0a4affff : Texas Instruments TVP4020 [Permedia 2]
0a4b0000-0a4bffff : QLogic Corp. ISP1020
0a4c0000-0a4c0fff : QLogic Corp. ISP1020
0a4c1000-0a4c17ff : Digi International AccelePort Xr/J
0a4c2000-0a4c23ff : Digital Equipment Corporation DECchip 21142/43
0a4c2000-0a4c23ff : tulip
0a4c3000-0a4c33ff : Digital Equipment Corporation DECchip 21142/43 (#2)
0a4c3000-0a4c33ff : tulip
0a4c4000-0a4c407f : Digi International AccelePort Xr/J
0a600000-0a60007f : tulip
0a601000-0a60107f : tulip
0a602000-0a60207f : tulip
0a603000-0a60307f : tulip
PCI information:
00:07.0 ISA bridge: Acer Laboratories Inc. [ALi] M1533 PCI to ISA Bridge [Aladdin IV] (rev c3)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
Latency: 0
00:09.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 29
Region 0: I/O ports at 8400 [size=128]
Region 1: Memory at 000000000a4c2000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 000000000a400000 [disabled] [size=256K]
00:0b.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 41)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 30
Region 0: I/O ports at 8480 [size=128]
Region 1: Memory at 000000000a4c3000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at 000000000a440000 [disabled] [size=256K]
00:0d.0 IDE interface: Acer Laboratories Inc. [ALi] M5229 IDE (rev c1) (prog-if f0)
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 8880 [size=16]
Region 1: I/O ports at 88b4 [size=4]
Region 2: I/O ports at 8890 [size=16]
Region 3: I/O ports at 88b4 [size=4]
Region 4: I/O ports at 88a0 [size=16]
00:0e.0 VGA compatible controller: Texas Instruments TVP4020 [Permedia 2] (rev 01) (prog-if 00 [VGA])
Subsystem: Elsa AG: Unknown device 0a32
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (48000ns min, 48000ns max)
Interrupt: pin A routed to IRQ 35
Region 0: Memory at 000000000a480000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at 0000000009000000 (32-bit, non-prefetchable) [size=8M]
Region 2: Memory at 0000000009800000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at 000000000a4a0000 [disabled] [size=64K]
00:0f.0 Communication controller: Digi International AccelePort Xr/J
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 39
Region 0: Memory at 000000000a4c4000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 8800 [size=128]
Region 2: Memory at 000000000a000000 (32-bit, non-prefetchable) [size=4M]
Expansion ROM at 000000000a4c1000 [disabled] [size=2K]
00:10.0 SCSI storage controller: Q Logic ISP1020 (rev 05)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 10
Interrupt: pin A routed to IRQ 43
Region 0: I/O ports at 8000 [size=256]
Region 1: Memory at 000000000a4c0000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at 000000000a4b0000 [disabled] [size=64K]
00:11.0 PCI bridge: Digital Equipment Corporation DECchip 21152 (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 10
Bus: primary=00, secondary=01, subordinate=01, sec-latency=255
I/O behind bridge: 00009000-00009fff
Memory behind bridge: 0a500000-0a6fffff
Prefetchable memory behind bridge: 0000000000100000-0000000000000000
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Bridge: PM- B3+
01:00.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 30)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 47
Region 0: I/O ports at 9000 [size=128]
Region 1: Memory at 000000000a600000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 000000000a500000 [disabled] [size=256K]
01:01.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 30)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 46
Region 0: I/O ports at 9080 [size=128]
Region 1: Memory at 000000000a601000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 000000000a540000 [disabled] [size=256K]
01:02.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 30)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 45
Region 0: I/O ports at 9400 [size=128]
Region 1: Memory at 000000000a602000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 000000000a580000 [disabled] [size=256K]
01:03.0 Ethernet controller: Digital Equipment Corporation DECchip 21142/43 (rev 30)
Subsystem: Digital Equipment Corporation DE500 Fast Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (5000ns min, 10000ns max), cache line size 10
Interrupt: pin A routed to IRQ 44
Region 0: I/O ports at 9480 [size=128]
Region 1: Memory at 000000000a603000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 000000000a5c0000 [disabled] [size=256K]
Scsi information:
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: DEC Model: RZ2DD-KS (C) DEC Rev: 0306
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: DEC Model: RZ2DD-KS (C) DEC Rev: 0306
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 05 Lun: 00
Vendor: DEC Model: TLZ10 (C) DEC Rev: 04a8
Type: Sequential-Access ANSI SCSI revision: 02
Thank you for the attention
C.Cappello (cappelc)
next reply other threads:[~2002-08-28 11:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-08-28 10:37 Corrado Cappello [this message]
2002-08-28 23:26 ` Wakko Warner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3D6CA7CC.685FE47@imads2.milano.italtel.it \
--to=corrado.cappello@italtel.it \
--cc=Daniele.Garbagnati@italtel.it \
--cc=Gianmarco.Vocino@italtel.it \
--cc=cappelc@hotmail.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®