From: Eyal Lebedinsky <eyal@eyal.emu.id.au>
To: list linux-kernel <linux-kernel@vger.kernel.org>
Subject: 2.4.19: sym53c8xx problems
Date: Sat, 05 Oct 2002 22:34:45 +1000 [thread overview]
Message-ID: <3D9EDC65.7C35221F@eyal.emu.id.au> (raw)
Actually I tried all the drivers for the ASUS SC200, a 53c810 based
card that used to work well. I have only a DDS-1 tape connected to
it but the drivers just do not cut it. Some refuse to load and others
get kernel panics. This gets even stranger. I proceeded to connect
the unit to a Compaq Proliant 6000 (four PIII Xeons). It has a 53c875
controller (three channels) and the sym53c8xx is crashing the system
if I try to access the tape (it does recognise it just fine when
loaded).
The newer driver (in sym53c8xx_2) does not get that far, the driver
locks up when I modprobe this driver.
Here are the boot messages, where the driver seems to OK (this is
the original sym53c8xx driver):
[BTW, why the final "scsi : 0 hosts left" message?]
[I will test again tomorrow, it is a new moon then...]
Oct 4 12:56:16 ssa28 kernel: SCSI subsystem driver Revision: 1.00
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 0, device 13,
function 0
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 4, device 9,
function 0
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 4, device 9,
function 1
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: rev 0x4 on pci bus 0 device
13 function 0 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: rev 0x14 on pci bus 4 device
9 function 0 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: rev 0x14 on pci bus 4 device
9 function 1 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: scsi0 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: scsi1 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: scsi2 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: Vendor: ARCHIVE Model: Python
28388-XXX Rev: 4.28
Oct 4 12:56:16 ssa28 kernel: Type:
Sequential-Access ANSI SCSI revision: 02
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: resetting chip
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: resetting chip
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: resetting chip
Oct 4 12:56:16 ssa28 kernel:
Oct 4 12:56:16 ssa28 kernel: inserting floppy driver for 2.4.18-ac3ser
Oct 4 12:56:16 ssa28 kernel: Floppy drive(s): fd0 is 1.44M
Oct 4 12:56:16 ssa28 kernel: FDC 0 is a National Semiconductor PC87306
Oct 4 12:56:16 ssa28 kernel: parport0: PC-style at 0x3bc [PCSPP]
Oct 4 12:56:16 ssa28 kernel: SCSI subsystem driver Revision: 1.00
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 0, device 13,
function 0
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 4, device 9,
function 0
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: at PCI bus 4, device 9,
function 1
Oct 4 12:56:16 ssa28 kernel: sym53c8xx: 53c875 detected
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: rev 0x4 on pci bus 0 device
13 function 0 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: rev 0x14 on pci bus 4 device
9 function 0 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: rev 0x14 on pci bus 4 device
9 function 1 irq 5
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: ID 7, Fast-20, Parity
Checking
Oct 4 12:56:16 ssa28 kernel: scsi0 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: scsi1 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: scsi2 : sym53c8xx-1.7.3c-20010512
Oct 4 12:56:16 ssa28 kernel: Vendor: ARCHIVE Model: Python
28388-XXX Rev: 4.28
Oct 4 12:56:16 ssa28 kernel: Type:
Sequential-Access ANSI SCSI revision: 02
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-0: resetting chip
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-1: resetting chip
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: detaching ...
Oct 4 12:56:16 ssa28 kernel: sym53c875-2: resetting chip
Oct 4 12:56:16 ssa28 kernel: scsi : 0 hosts left.
--
Eyal Lebedinsky (eyal@eyal.emu.id.au) <http://samba.org/eyal/>
next reply other threads:[~2002-10-05 12:29 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-05 12:34 Eyal Lebedinsky [this message]
2002-10-05 15:24 ` Mr. James W. Laferriere
2002-10-05 23:36 ` Eyal Lebedinsky
2002-10-07 4:22 ` Mr. James W. Laferriere
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3D9EDC65.7C35221F@eyal.emu.id.au \
--to=eyal@eyal.emu.id.au \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®