From: Eyal Lebedinsky <eyal@eyal.emu.id.au>
To: list linux-kernel <linux-kernel@vger.kernel.org>
Subject: 2.4.21-rc6: usb-uhci.c: interrupt
Date: Thu, 05 Jun 2003 09:31:19 +1000 [thread overview]
Message-ID: <3EDE8147.5B9A7093@eyal.emu.id.au> (raw)
For some time now I notice these messages when I use my SCSI
tape:
kernel: usb-uhci.c: interrupt, status 28, frame# 1015
with different frame# each time.
I used a USB mass-storage device a while back, for a short time,
it was since removed.
I am chasing some data corruption and will suspect everything
at this point. Any chance that this causes a problem for scsi
devices?
Anyway, I am rather sure that the usb system should keep quiet
as it is not accessed at all.
boot messages:
==============
May 29 21:40:45 eyal kernel: usb.c: registered new driver usbdevfs
May 29 21:40:45 eyal kernel: usb.c: registered new driver hub
May 29 21:40:45 eyal kernel: usb-uhci.c: $Revision: 1.275 $ time
20:19:46 May 29 2003
May 29 21:40:45 eyal kernel: usb-uhci.c: High bandwidth mode enabled
May 29 21:40:45 eyal kernel: usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 5
May 29 21:40:45 eyal kernel: usb-uhci.c: Detected 2 ports
May 29 21:40:45 eyal kernel: usb.c: new USB bus registered, assigned bus
number 1
May 29 21:40:45 eyal kernel: hub.c: USB hub found
May 29 21:40:45 eyal kernel: hub.c: 2 ports detected
May 29 21:40:45 eyal kernel: usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
May 29 21:40:45 eyal kernel: usb-uhci.c: Detected 2 ports
May 29 21:40:45 eyal kernel: usb.c: new USB bus registered, assigned bus
number 2
May 29 21:40:45 eyal kernel: hub.c: USB hub found
May 29 21:40:45 eyal kernel: hub.c: 2 ports detected
May 29 21:40:45 eyal kernel: usb-uhci.c: v1.275:USB Universal Host
Controller Interface driver
Mass-storage usage
==================
May 30 19:16:13 eyal kernel: hub.c: new USB device 00:07.2-1, assigned
address 2
May 30 19:16:13 eyal kernel: usb.c: USB device 2 (vend/prod 0xc76/0x7)
is not claimed by any active driver.
May 30 19:18:56 eyal kernel: SCSI subsystem driver Revision: 1.00
May 30 19:18:57 eyal kernel: Initializing USB Mass Storage driver...
May 30 19:18:57 eyal kernel: usb.c: registered new driver usb-storage
May 30 19:18:57 eyal kernel: scsi0 : SCSI emulation for USB Mass Storage
devices
May 30 19:18:57 eyal kernel: Vendor:
Model: Rev:
May 30 19:18:57 eyal kernel: Type:
Direct-Access ANSI SCSI revision: 02
May 30 19:18:57 eyal kernel: USB Mass Storage support registered.
May 30 19:18:57 eyal kernel: Attached scsi removable disk sda at scsi0,
channel 0, id 0, lun 0
May 30 19:18:57 eyal kernel: SCSI device sda: 512000 512-byte hdwr
sectors (262 MB)
May 30 19:18:57 eyal kernel: sda: Write Protect is off
May 30 19:18:57 eyal kernel: sda: sda1
May 30 19:21:49 eyal kernel: usb.c: deregistering driver usb-storage
May 30 19:21:49 eyal kernel: scsi : 0 hosts left.
May 30 19:21:53 eyal kernel: usb.c: USB disconnect on device 00:07.2-1
address 2
some stray messages
===================
Jun 3 20:16:15 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
607
Jun 3 20:18:12 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
801
Jun 3 20:18:12 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
329
Jun 3 20:18:40 eyal kernel: usb-uhci.c: interrupt, status 30, frame#
1309
Jun 3 20:20:51 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
1335
Jun 3 20:27:00 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
440
Jun 4 00:24:13 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
1015
Jun 4 01:00:04 eyal kernel: usb-uhci.c: interrupt, status 28, frame#
240
# lsmod
=======
Module Size Used by Tainted: P
st 27124 0 (autoclean)
dc395x_trm 47168 0 (autoclean)
sg 24772 0 (autoclean)
sd_mod 10172 0 (autoclean)
scsi_mod 84680 4 [st dc395x_trm sg sd_mod]
bttv 77568 0 (autoclean)
tuner 9540 1
videodev 5664 3 (autoclean) [bttv]
i2c-algo-bit 8300 1 (autoclean) [bttv]
es1371 27136 1 (autoclean)
gameport 1548 0 (autoclean) [es1371]
ac97_codec 10912 0 (autoclean) [es1371]
soundcore 3588 4 (autoclean) [bttv es1371]
nvidia 1540320 10 (autoclean)
usb-uhci 21764 0 (unused)
usbcore 57152 1 [usb-uhci]
ipt_limit 960 2 (autoclean)
ipt_LOG 3200 3 (autoclean)
ipt_state 608 4 (autoclean)
iptable_filter 1760 1 (autoclean)
ip_conntrack_ftp 3808 0 (unused)
ip_conntrack 17396 2 [ipt_state ip_conntrack_ftp]
ip_tables 10752 4 [ipt_limit ipt_LOG ipt_state
iptable_filter]
ide-cd 29024 0 (autoclean)
cdrom 29024 0 (autoclean) [ide-cd]
via686a 8228 0
eeprom 3552 0 (unused)
i2c-proc 6624 0 [via686a eeprom]
i2c-isa 1252 0 (unused)
i2c-viapro 3912 0 (unused)
i2c-core 15112 0 [bttv tuner i2c-algo-bit via686a
eeprom i2c-proc i2c-isa i2c-viapro]
3c509 10400 1 (autoclean)
nls_iso8859-1 2880 2 (autoclean)
nls_cp437 4384 2 (autoclean)
msdos 4988 2 (autoclean)
fat 29944 0 (autoclean) [msdos]
serial 43808 1 (autoclean)
isa-pnp 28796 0 (autoclean) [3c509 serial]
rtc 6012 0 (autoclean)
unix 14212 56 (autoclean)
# cat /proc/interrupts
======================
CPU0
0: 56055069 XT-PIC timer
1: 162333 XT-PIC keyboard
2: 0 XT-PIC cascade
4: 29 XT-PIC serial
5: 11057 XT-PIC usb-uhci, usb-uhci, bttv
8: 3 XT-PIC rtc
9: 36502293 XT-PIC nvidia
10: 2546310 XT-PIC es1371, DC395x_TRM
11: 15725277 XT-PIC eth0
12: 2104939 XT-PIC PS/2 Mouse
14: 3748686 XT-PIC ide0
15: 19 XT-PIC ide1
NMI: 0
ERR: 0
--
Eyal Lebedinsky (eyal@eyal.emu.id.au) <http://samba.org/eyal/>
next reply other threads:[~2003-06-04 23:17 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-06-04 23:31 Eyal Lebedinsky [this message]
2003-06-06 9:51 ` Eyal Lebedinsky
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3EDE8147.5B9A7093@eyal.emu.id.au \
--to=eyal@eyal.emu.id.au \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®