Re: [PATCH 1/2] arm64: dts: ti: k3-j7200-som-p0: main_i2c0 have an ioexpander on the SOM

[Vignesh Raghavendra <vigneshr@ti.com>]

On 11/19/20 6:56 PM, Peter Ujfalusi wrote:
> It is used to control several SOM level muxes to make sure that the correct
> signals are routed to the correct pin on the SOM <-> CPB connectors.
> 
> Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
> ---

Yes, there is indeed a I2C GPIO expander on SOM that's missing from DT
today. So this change looks good to me.

Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>

Regards
Vignesh

>  .../dts/ti/k3-j7200-common-proc-board.dts     | 11 --------
>  arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi   | 26 +++++++++++++++++++
>  2 files changed, 26 insertions(+), 11 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> index 6b3863108571..2721137d8943 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
> @@ -43,13 +43,6 @@ J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>  };
>  
>  &main_pmx0 {
> -	main_i2c0_pins_default: main-i2c0-pins-default {
> -		pinctrl-single,pins = <
> -			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> -			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> -		>;
> -	};
> -
>  	main_i2c1_pins_default: main-i2c1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
> @@ -146,10 +139,6 @@ &cpsw_port1 {
>  };
>  
>  &main_i2c0 {
> -	pinctrl-names = "default";
> -	pinctrl-0 = <&main_i2c0_pins_default>;
> -	clock-frequency = <400000>;
> -
>  	exp1: gpio@20 {
>  		compatible = "ti,tca6416";
>  		reg = <0x20>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> index fbd17d38f6b6..7b5e9aa0324e 100644
> --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
> @@ -48,6 +48,15 @@ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
>  	};
>  };
>  
> +&main_pmx0 {
> +	main_i2c0_pins_default: main-i2c0-pins-default {
> +		pinctrl-single,pins = <
> +			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
> +			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
> +		>;
> +	};
> +};
> +
>  &hbmc {
>  	/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
>  	 * appropriate node based on board detection
> @@ -131,3 +140,20 @@ &mailbox0_cluster10 {
>  &mailbox0_cluster11 {
>  	status = "disabled";
>  };
> +
> +&main_i2c0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&main_i2c0_pins_default>;
> +	clock-frequency = <400000>;
> +
> +	exp_som: gpio@21 {
> +		compatible = "ti,tca6408";
> +		reg = <0x21>;
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +		gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
> +				  "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
> +				  "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
> +				  "GPIO_LIN_EN", "CAN_STB";
> +	};
> +};
>