From: Allen Hubbe <Allen.Hubbe@emc.com>
To: linux-ntb@googlegroups.com
Cc: linux-kernel@vger.kernel.org, linux-pci@vger.kernel.org,
Jon Mason <jdmason@kudzu.us>, Dave Jiang <dave.jiang@intel.com>,
Allen Hubbe <Allen.Hubbe@emc.com>
Subject: [PATCH v4 10/19] NTB: Add parameters for Intel SNB B2B addresses
Date: Wed, 10 Jun 2015 05:08:15 -0400 [thread overview]
Message-ID: <3a9a0aa9066748dcaf21da955ac6361ca3b6d280.1433925092.git.Allen.Hubbe@emc.com> (raw)
In-Reply-To: <cover.1433925092.git.Allen.Hubbe@emc.com>
In-Reply-To: <cover.1433925092.git.Allen.Hubbe@emc.com>
Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
---
Documentation/ntb.txt | 10 +++++
drivers/ntb/hw/intel/ntb_hw_intel.c | 77 ++++++++++++++++++++++++++++---------
2 files changed, 68 insertions(+), 19 deletions(-)
diff --git a/Documentation/ntb.txt b/Documentation/ntb.txt
index 725ba1e6c127..00a3f92832a5 100644
--- a/Documentation/ntb.txt
+++ b/Documentation/ntb.txt
@@ -56,3 +56,13 @@ Module Parameters:
* b2b\_mw\_share - If the peer ntb is to be accessed via a memory window, and if
the memory window is large enough, still allow the client to use the
second half of the memory window for address translation to the peer.
+* snb\_b2b\_usd\_bar2\_addr64 - If using B2B topology on Xeon hardware, use this
+ 64 bit address on the bus between the NTB devices for the window at
+ BAR2, on the upstream side of the link.
+* snb\_b2b\_usd\_bar4\_addr64 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_usd\_bar4\_addr32 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_usd\_bar5\_addr32 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_dsd\_bar2\_addr64 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_dsd\_bar4\_addr64 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_dsd\_bar4\_addr32 - See *snb\_b2b\_bar2\_addr64*.
+* snb\_b2b\_dsd\_bar5\_addr32 - See *snb\_b2b\_bar2\_addr64*.
diff --git a/drivers/ntb/hw/intel/ntb_hw_intel.c b/drivers/ntb/hw/intel/ntb_hw_intel.c
index ff397fae9cf4..3448d5fbd003 100644
--- a/drivers/ntb/hw/intel/ntb_hw_intel.c
+++ b/drivers/ntb/hw/intel/ntb_hw_intel.c
@@ -72,20 +72,6 @@ MODULE_AUTHOR("Intel Corporation");
#define bar0_off(base, bar) ((base) + ((bar) << 2))
#define bar2_off(base, bar) bar0_off(base, (bar) - 2)
-static int b2b_mw_idx = -1;
-module_param(b2b_mw_idx, int, 0644);
-MODULE_PARM_DESC(b2b_mw_idx, "Use this mw idx to access the peer ntb. A "
- "value of zero or positive starts from first mw idx, and a "
- "negative value starts from last mw idx. Both sides MUST "
- "set the same value here!");
-
-static unsigned int b2b_mw_share;
-module_param(b2b_mw_share, uint, 0644);
-MODULE_PARM_DESC(b2b_mw_share, "If the b2b mw is large enough, configure the "
- "ntb so that the peer ntb only occupies the first half of "
- "the mw, so the second half can still be used as a mw. Both "
- "sides MUST set the same value here!");
-
static const struct intel_ntb_reg bwd_reg;
static const struct intel_ntb_alt_reg bwd_pri_reg;
static const struct intel_ntb_alt_reg bwd_sec_reg;
@@ -98,14 +84,67 @@ static const struct intel_ntb_alt_reg snb_sec_reg;
static const struct intel_ntb_alt_reg snb_b2b_reg;
static const struct intel_ntb_xlat_reg snb_pri_xlat;
static const struct intel_ntb_xlat_reg snb_sec_xlat;
-static const struct intel_b2b_addr snb_b2b_usd_addr;
-static const struct intel_b2b_addr snb_b2b_dsd_addr;
-
+static struct intel_b2b_addr snb_b2b_usd_addr;
+static struct intel_b2b_addr snb_b2b_dsd_addr;
static const struct ntb_dev_ops intel_ntb_ops;
static const struct file_operations intel_ntb_debugfs_info;
static struct dentry *debugfs_dir;
+static int b2b_mw_idx = -1;
+module_param(b2b_mw_idx, int, 0644);
+MODULE_PARM_DESC(b2b_mw_idx, "Use this mw idx to access the peer ntb. A "
+ "value of zero or positive starts from first mw idx, and a "
+ "negative value starts from last mw idx. Both sides MUST "
+ "set the same value here!");
+
+static unsigned int b2b_mw_share;
+module_param(b2b_mw_share, uint, 0644);
+MODULE_PARM_DESC(b2b_mw_share, "If the b2b mw is large enough, configure the "
+ "ntb so that the peer ntb only occupies the first half of "
+ "the mw, so the second half can still be used as a mw. Both "
+ "sides MUST set the same value here!");
+
+module_param_named(snb_b2b_usd_bar2_addr64,
+ snb_b2b_usd_addr.bar2_addr64, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_usd_bar2_addr64,
+ "SNB B2B USD BAR 2 64-bit address");
+
+module_param_named(snb_b2b_usd_bar4_addr64,
+ snb_b2b_usd_addr.bar4_addr64, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_usd_bar2_addr64,
+ "SNB B2B USD BAR 4 64-bit address");
+
+module_param_named(snb_b2b_usd_bar4_addr32,
+ snb_b2b_usd_addr.bar4_addr32, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_usd_bar2_addr64,
+ "SNB B2B USD split-BAR 4 32-bit address");
+
+module_param_named(snb_b2b_usd_bar5_addr32,
+ snb_b2b_usd_addr.bar5_addr32, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_usd_bar2_addr64,
+ "SNB B2B USD split-BAR 5 32-bit address");
+
+module_param_named(snb_b2b_dsd_bar2_addr64,
+ snb_b2b_dsd_addr.bar2_addr64, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_dsd_bar2_addr64,
+ "SNB B2B DSD BAR 2 64-bit address");
+
+module_param_named(snb_b2b_dsd_bar4_addr64,
+ snb_b2b_dsd_addr.bar4_addr64, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_dsd_bar2_addr64,
+ "SNB B2B DSD BAR 4 64-bit address");
+
+module_param_named(snb_b2b_dsd_bar4_addr32,
+ snb_b2b_dsd_addr.bar4_addr32, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_dsd_bar2_addr64,
+ "SNB B2B DSD split-BAR 4 32-bit address");
+
+module_param_named(snb_b2b_dsd_bar5_addr32,
+ snb_b2b_dsd_addr.bar5_addr32, ullong, 0644);
+MODULE_PARM_DESC(snb_b2b_dsd_bar2_addr64,
+ "SNB B2B DSD split-BAR 5 32-bit address");
+
#ifndef ioread64
#ifdef readq
#define ioread64 readq
@@ -2078,14 +2117,14 @@ static const struct intel_ntb_xlat_reg snb_sec_xlat = {
.bar2_xlat = SNB_SBAR23XLAT_OFFSET,
};
-static const struct intel_b2b_addr snb_b2b_usd_addr = {
+static struct intel_b2b_addr snb_b2b_usd_addr = {
.bar2_addr64 = SNB_B2B_BAR2_USD_ADDR64,
.bar4_addr64 = SNB_B2B_BAR4_USD_ADDR64,
.bar4_addr32 = SNB_B2B_BAR4_USD_ADDR32,
.bar5_addr32 = SNB_B2B_BAR5_USD_ADDR32,
};
-static const struct intel_b2b_addr snb_b2b_dsd_addr = {
+static struct intel_b2b_addr snb_b2b_dsd_addr = {
.bar2_addr64 = SNB_B2B_BAR2_DSD_ADDR64,
.bar4_addr64 = SNB_B2B_BAR4_DSD_ADDR64,
.bar4_addr32 = SNB_B2B_BAR4_DSD_ADDR32,
--
2.4.0.rc0.43.gcf8a8c6
next prev parent reply other threads:[~2015-06-10 14:14 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-06-10 9:08 [PATCH v4 00/19] NTB: Add NTB hardware abstraction layer Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 01/19] NTB: Move files in preparation for NTB abstraction Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 02/19] NTB: Add NTB hardware abstraction layer Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 03/19] NTB: Split ntb_hw_intel and ntb_transport drivers Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 04/19] NTB: Read peer info from local SPAD in transport Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 05/19] NTB: Enable link for Intel root port mode in probe Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 06/19] NTB: Check the device ID to set errata flags Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 07/19] NTB: Differentiate transport link down messages Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 08/19] NTB: Do not advance transport RX on link down Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 09/19] NTB: Reset transport QP link stats on down Allen Hubbe
2015-06-10 9:08 ` Allen Hubbe [this message]
2015-06-10 9:08 ` [PATCH v4 11/19] NTB: Add ping pong test client Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 12/19] NTB: Add tool " Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 13/19] NTB: Rate limit ntb_qp_link_work Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 14/19] NTB: Use NUMA memory and DMA chan in transport Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 15/19] NTB: Use NUMA memory in Intel driver Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 16/19] NTB: Improve performance with write combining Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 17/19] NTB: Default to CPU memcpy for performance Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 18/19] NTB: Rename Intel code names to platform names Allen Hubbe
2015-06-10 9:08 ` [PATCH v4 19/19] NTB: Increase transport MTU to 64k from 16k Allen Hubbe
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3a9a0aa9066748dcaf21da955ac6361ca3b6d280.1433925092.git.Allen.Hubbe@emc.com \
--to=allen.hubbe@emc.com \
--cc=dave.jiang@intel.com \
--cc=jdmason@kudzu.us \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-ntb@googlegroups.com \
--cc=linux-pci@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®