From: Heinrich Schuchardt <xypron.glpk@gmx.de>
To: khilman@baylibre.com
Cc: "Heiko Stübner" <heiko@sntech.de>,
"Rob Herring" <robh+dt@kernel.org>,
"Mark Rutland" <mark.rutland@arm.com>,
"Catalin Marinas" <catalin.marinas@arm.com>,
"Will Deacon" <will.deacon@arm.com>,
"Shawn Lin" <shawn.lin@rock-chips.com>,
"Vagrant Cascadian" <vagrant@debian.org>,
"Enric Balletbo i Serra" <enric.balletbo@collabora.com>,
"Pierre-Hugues Husson" <phh@phh.me>,
"Jianqun Xu" <jay.xu@rock-chips.com>,
"Kever Yang" <kever.yang@rock-chips.com>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/1] arm64: dts: rockchip: correct voltage selector Firefly-RK3399
Date: Thu, 21 Jun 2018 02:57:02 +0200 [thread overview]
Message-ID: <3b6e37c8-0ee2-1723-1aa8-499fcb30471c@gmx.de> (raw)
In-Reply-To: <cd7447bc-1c3d-29ca-9671-144b1f474711@gmx.de>
On 06/20/2018 09:57 PM, Heinrich Schuchardt wrote:
> On 06/20/2018 11:15 AM, Heiko Stübner wrote:
>> Hi Heinrich,
>>
>> Am Mittwoch, 20. Juni 2018, 07:59:34 CEST schrieb Heinrich Schuchardt:
>>> On 06/20/2018 01:21 AM, Heiko Stuebner wrote:
>>>> Am Donnerstag, 14. Juni 2018, 14:55:27 CEST schrieb Heiko Stuebner:
>>>>> Am Montag, 4. Juni 2018, 19:15:23 CEST schrieb Heinrich Schuchardt:
>>>>>> Without this patch the Firefly-RK3399 board boot process hangs after
>>>>>> these
>>>>>>
>>>>>> lines:
>>>>>> fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected!
>>>>>> fan53555-reg: supplied by vcc_sys
>>>>>> vcc1v8_s3: supplied by vcc_1v8
>>>>>>
>>>>>> Blacklisting driver fan53555 allows booting.
>>>>>>
>>>>>> The device tree uses a value of fcs,suspend-voltage-selector different
>>>>>> to
>>>>>> any other board.
>>>>>>
>>>>>> Changing this setting to the usual value is sufficient to enable
>>>>>> booting.
>>>>>>
>>>>>> Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
>>>>>
>>>>> applied for 4.19.
>>>>
>>>> and dropped again.
>>>>
>>>> Sadly it looks like the patch causes conflicts with at least one firefly
>>>> board in a kernelci lab. My own is currently not ready to use, so I cannot
>>>> look myself right now.
>>>>
>>>> The issue kernelci people described sounded quite a lot like the one
>>>> in your commit message, so my current theory is that the
>>>> suspend-voltage-selector must in some form corespond to the
>>>> cpu_b_sleep_h gpio setting we're currently not handling at all, which
>>>> would therefore depend on how the bootloader sets this up.
>>>
>>> please, provide a link to the log displaying the issue and the contact
>>> who can provide the exact setup.
>>>
>>> I have been testing with U-Boot as boot loader.
>>
>> failing boot can be found on
>> https://kernelci.org/boot/id/5b2a053d59b514569079a872/
>>
>> As this board is sitting in the "lab-baylibre-seattle", I guess
>> Kevin Hilman (Cc'ed now) is the one that can say a bit more about the
>> board setup.
>>
>>
>> The more interesting question would be how to make sure we don't
>> die with possible different bootloader versions. As I don't really thing
>> "upgrade your bootloader" is an always valid option.
>>
>>
>> Heiko
>>
>
> Hi Kevin,
>
> the RK3399-Firefly was booted on lab-baylibre-seattle with
> U-Boot 2017.05-rc3-00131-gf79fd58d5f5c-dirty
>
> f79fd58d5f5c is not a commit in U-Boot master.
> The version number tells us it is 131 patches ahead of U-Boot 2017.05-rc3.
> Dirty means the source contained uncommitted changes.
>
> Unfortunately this is not a reproducible test environment.
> Could you, please, provide the build recipe to reproduce the U-Boot
> BayLibre is using?
> Would it be possible to use mainline U-Boot in kernelci for this board?
>
> Best regards
>
> Heinrich
>
I have now built the last available release of U-Boot (v2018.05)
according to the following recipe:
git clone https://github.com/xypron/u-boot-build.git
cd u-boot-build/
git checkout firefly-rk3399-rkloader
# commit 251b12fb4f0eabfff2d0552d0807d8ddc44ae2aa
# tag firefly-rk3399-rkloader-v2018.05
make
make install DESTDIR=foo
cd foo/usr/lib/u-boot/firefly-rk3399/
# be careful to specify your SD card as device!
./sd_fusing /dev/sdX
# in U-Boot 2018.05 (Jun 21 2018 - 02:33:12 +0200)
load mmc 1:1 ${fdt_addr_r} 2018-06-20/rk3399-firefly.dtb
load mmc 1:1 ${kernel_addr_r} 2018-06-20/Image
booti ${kernel_addr_r} - ${fdt_addr_r}
The error observed in kernelci when initializing the FAN53555 driver
does not occur.
The console log is here:
https://gist.github.com/xypron/34b6485deabfc8172f978b5a99705466
Best regards
Heinrich
next prev parent reply other threads:[~2018-06-21 0:57 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-04 17:15 Heinrich Schuchardt
2018-06-04 21:45 ` Heinrich Schuchardt
2018-06-14 12:55 ` Heiko Stuebner
2018-06-19 23:21 ` Heiko Stuebner
2018-06-20 5:59 ` Heinrich Schuchardt
2018-06-20 9:15 ` Heiko Stübner
2018-06-20 19:57 ` Heinrich Schuchardt
2018-06-21 0:57 ` Heinrich Schuchardt [this message]
2018-06-21 11:37 ` Heiko Stuebner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3b6e37c8-0ee2-1723-1aa8-499fcb30471c@gmx.de \
--to=xypron.glpk@gmx.de \
--cc=catalin.marinas@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=enric.balletbo@collabora.com \
--cc=heiko@sntech.de \
--cc=jay.xu@rock-chips.com \
--cc=kever.yang@rock-chips.com \
--cc=khilman@baylibre.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=mark.rutland@arm.com \
--cc=phh@phh.me \
--cc=robh+dt@kernel.org \
--cc=shawn.lin@rock-chips.com \
--cc=vagrant@debian.org \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®