From: Neil Armstrong <neil.armstrong@linaro.org>
To: Daniel Thompson <danielt@kernel.org>
Cc: Lee Jones <lee@kernel.org>, Jingoo Han <jingoohan1@gmail.com>,
Pavel Machek <pavel@kernel.org>, Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, Helge Deller <deller@gmx.de>,
dri-devel@lists.freedesktop.org, linux-leds@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-fbdev@vger.kernel.org, KancyJoe <kancy2333@outlook.com>,
Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Subject: Re: [PATCH v3 1/2] dt-bindings: leds: backlight: document the SY7758 6-channel High Efficiency LED Driver
Date: Fri, 29 May 2026 14:50:43 +0200 [thread overview]
Message-ID: <4001cf6a-b7de-4933-96bc-c9b4ccb53e4d@linaro.org> (raw)
In-Reply-To: <ahlr5PnX5O0tEd6G@aspen.lan>
On 5/29/26 12:35, Daniel Thompson wrote:
> On Fri, May 29, 2026 at 12:16:07PM +0200, Neil Armstrong wrote:
>> On 5/29/26 12:07, Daniel Thompson wrote:
>>> On Tue, May 19, 2026 at 10:43:38AM +0200, Neil Armstrong wrote:
>>>> Document the Silergy SY7758 6-channel High Efficiency LED Driver
>>>> used for backlight brightness control.
>>>>
>>>> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
>>>> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
>>>> ---
>>>> .../bindings/leds/backlight/silergy,sy7758.yaml | 53 ++++++++++++++++++++++
>>>> 1 file changed, 53 insertions(+)
>>>>
>>>> diff --git a/Documentation/devicetree/bindings/leds/backlight/silergy,sy7758.yaml b/Documentation/devicetree/bindings/leds/backlight/silergy,sy7758.yaml
>>>> new file mode 100644
>>>> index 000000000000..80e978d691c2
>>>> --- /dev/null
>>>> +++ b/Documentation/devicetree/bindings/leds/backlight/silergy,sy7758.yaml
>>>> @@ -0,0 +1,53 @@
>>>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>>>> +%YAML 1.2
>>>> +---
>>>> +$id: http://devicetree.org/schemas/leds/backlight/silergy,sy7758.yaml#
>>>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>>>> +
>>>> +title: Silergy SY7758 6-channel High Efficiency LED Driver
>>>> +
>>>> +maintainers:
>>>> + - Neil Armstrong <neil.armstrong@linaro.org>
>>>> +
>>>> +description:
>>>> + Silergy SY7758 is a high efficiency 6-channels LED backlight
>>>> + driver with I2C brightness control.
>>>> +
>>>> +allOf:
>>>> + - $ref: common.yaml#
>>>> +
>>>> +properties:
>>>> + compatible:
>>>> + const: silergy,sy7758
>>>> +
>>>> + reg:
>>>> + maxItems: 1
>>>> +
>>>> + vddio-supply: true
>>>> +
>>>> + enable-gpios:
>>>> + maxItems: 1
>>>> +
>>>> +required:
>>>> + - compatible
>>>> + - reg
>>>> + - vddio-supply
>>>
>>> Sorry for missing this in v2 but is vddio-supply really a required
>>> property?
>>>
>>> It's unusual for supplies to be mandatory (and the it is not mandatory
>>> in the driver implementation).
>>
>> This device is a little bit special, the VDDIO regulator is used to provide
>> power for the I/O via the enable input, so basically the enable gpio power
>> level is provided by VDDIO.
>
> I don't follow. The EN pin acts as both VDDIO and as an enable but it's
> still effectively a power rail isn't it (albeit one with very low current
> draw).
Here's the datasheet description:
```
Dual-purpose pin serving both as a chip enable and as a power supply
reference for PWM, SDA, and SCL inputs.
```
The VDD input is directly provided by the panel, so Linux has no control
of it so I haven't added it.
>
> It looked to me like the correct way to model to two power rails
> going into the chip is vdd-supply (main power supply) and vddio-supply
> (EN/VDDIO) I don't understand why a single pin needs both a regulator
> *and* a GPIO in the DT bindings?
I don't have a the schematics of the board, but as I understood one gpio is
actually enabling an regulator which provides power to the IC (vddio) and
a second gpio will either drive the EN signal to GND or VDDIO to provide a
clean rising edge on the EN pin.
So it's not really 2 regulators, and having regulators means the enable
signal can be shared and would have regulator characteristics which it hasn't.
>
>> This is the recommended way from the datasheet, and I assume it will be used
>> like that on other platforms (if it exists...)
>>
>> This is why it's mandatory and enabled first before setting the enable pin.
>
> It's not mandatory for the C implementation. devm_regulator_get_enable()
> will provide a dummy regulator if the property is omitted.
So yeah if you prefer I'll re-spin with the vddio regulator as optional
because between both, the VDDIO is the only which could be shared with
other devices or always-on.
Neil
>
>
> Daniel.
next prev parent reply other threads:[~2026-05-29 12:50 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-19 8:43 [PATCH v3 0/2] backlight: Add SY7758 6-channel High Efficiency LED Driver support Neil Armstrong
2026-05-19 8:43 ` [PATCH v3 1/2] dt-bindings: leds: backlight: document the SY7758 6-channel High Efficiency LED Driver Neil Armstrong
2026-05-29 10:07 ` Daniel Thompson
2026-05-29 10:16 ` Neil Armstrong
2026-05-29 10:35 ` Daniel Thompson
2026-05-29 12:50 ` Neil Armstrong [this message]
2026-05-29 14:15 ` Daniel Thompson
2026-05-29 14:36 ` Daniel Thompson
2026-05-29 19:17 ` Neil Armstrong
2026-05-19 8:43 ` [PATCH v3 2/2] backlight: Add SY7758 6-channel High Efficiency LED Driver support Neil Armstrong
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4001cf6a-b7de-4933-96bc-c9b4ccb53e4d@linaro.org \
--to=neil.armstrong@linaro.org \
--cc=conor+dt@kernel.org \
--cc=danielt@kernel.org \
--cc=deller@gmx.de \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jingoohan1@gmail.com \
--cc=kancy2333@outlook.com \
--cc=krzk+dt@kernel.org \
--cc=krzysztof.kozlowski@oss.qualcomm.com \
--cc=lee@kernel.org \
--cc=linux-fbdev@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=pavel@kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®