From: "K.R. Foley" <kr@cybsft.com>
To: Ingo Molnar <mingo@elte.hu>
Cc: linux-kernel@vger.kernel.org, Lee Revell <rlrevell@joe-job.com>,
Rui Nuno Capela <rncbc@rncbc.org>,
Florian Schmidt <mista.tapas@gmx.net>,
Mark_H_Johnson@raytheon.com,
Fernando Pablo Lopez-Lezcano <nando@ccrma.Stanford.EDU>
Subject: Re: [patch] voluntary-preempt-2.6.9-rc3-mm3-T3
Date: Fri, 08 Oct 2004 09:03:25 -0500 [thread overview]
Message-ID: <41669E2D.6060705@cybsft.com> (raw)
In-Reply-To: <20041008070252.GA30823@elte.hu>
[-- Attachment #1: Type: text/plain, Size: 2152 bytes --]
Ingo Molnar wrote:
> * K.R. Foley <kr@cybsft.com> wrote:
>
>
>>Ingo Molnar wrote:
>>
>>>* K.R. Foley <kr@cybsft.com> wrote:
>>>
>>>
>>>
>>>>>For me, this one wants to panic on boot when trying to find the root
>>>>>filesystem. Acts like either the aic7xxx module is missing (which I
>>>>>don't think is the case) or hosed, or it's having trouble with the label
>>>>>for the root partition (Fedora system). Will investigate further when I
>>>>>get home tonight, unless something jumps out at anyone.
>>>>>
>>>>>kr
>>>>
>>>>For clarification: This appears to be a problem in 2.6.9-rc3-mm3 also.
>>>
>>>
>>>try root=/dev/sda3 (or whereever your root fs is) instead of
>>>root=LABEL=/, in /etc/grub.conf.
>>>
>>> Ingo
>>>
>>
>>Thanks. Tried that just to be sure. However, I don't seem to be the
>>only one having this problem with aic7xxx.
>
>
Ingo,
First let me say that, in case you haven't been following the other
thread about this "2.6.9-rc3-mm3 fails to detect aic7xxx", I resolved
this by backing out the bk-scsi.patch and bk-scsi-target.patch. Without
those everything works fine.
> could you send me the following info:
>
> - full log of a failed boot
I would like to be able to be able to send you this, but it doesn't get
to the point of logging. It dies trying to find the / device. On the
screen it displays the parameters for the chosen option in grub.conf,
says its uncompressing, then displays the Nash version info, then
displays a panic message about not finding the root device. Something on
the order of:
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
Do you think that I would actually get to see more info out of this if I
connect a serial console?
> - full log of a successful boot
Attached.
> - the output of 'mount'
[root@porky root]# mount
/dev/sda2 on / type ext3 (rw)
none on /proc type proc (rw)
none on /sys type sysfs (rw)
none on /dev/pts type devpts (rw,gid=5,mode=620)
/dev/sda1 on /boot type ext3 (rw)
/dev/sdb1 on /proj1 type ext3 (rw)
none on /dev/shm type tmpfs (rw)
sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw)
>
> Ingo
>
thanks,
kr
[-- Attachment #2: bootlog.ok --]
[-- Type: text/plain, Size: 23743 bytes --]
Oct 8 06:48:42 porky syslogd 1.4.1: restart.
Oct 8 06:48:42 porky syslog: syslogd startup succeeded
Oct 8 06:48:42 porky syslog: klogd startup succeeded
Oct 8 06:48:42 porky kernel: klogd 1.4.1, log source = /proc/kmsg started.
Oct 8 06:48:42 porky kernel: Linux version 2.6.9-rc3-mm3-VP-T3 (kr@porky.cybersoft.int) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #8 SMP Thu Oct 7 23:07:40 CDT 2004
Oct 8 06:48:42 porky kernel: BIOS-provided physical RAM map:
Oct 8 06:48:42 porky kernel: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
Oct 8 06:48:42 porky kernel: BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
Oct 8 06:48:42 porky kernel: BIOS-e820: 0000000000100000 - 000000001ff9e000 (usable)
Oct 8 06:48:42 porky kernel: BIOS-e820: 000000001ff9e000 - 0000000020000000 (reserved)
Oct 8 06:48:42 porky kernel: BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
Oct 8 06:48:42 porky kernel: BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
Oct 8 06:48:42 porky kernel: BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Oct 8 06:48:42 porky kernel: 0MB HIGHMEM available.
Oct 8 06:48:42 porky kernel: 511MB LOWMEM available.
Oct 8 06:48:42 porky kernel: found SMP MP-table at 000fe710
Oct 8 06:48:42 porky kernel: DMI 2.3 present.
Oct 8 06:48:42 porky irqbalance: irqbalance startup succeeded
Oct 8 06:48:42 porky kernel: ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Oct 8 06:48:42 porky kernel: Processor #0 6:8 APIC version 17
Oct 8 06:48:42 porky kernel: ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Oct 8 06:48:42 porky kernel: Processor #1 6:8 APIC version 17
Oct 8 06:48:42 porky kernel: ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
Oct 8 06:48:42 porky kernel: ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
Oct 8 06:48:42 porky kernel: Using ACPI for processor (LAPIC) configuration information
Oct 8 06:48:42 porky kernel: Intel MultiProcessor Specification v1.4
Oct 8 06:48:42 porky kernel: Virtual Wire compatibility mode.
Oct 8 06:48:42 porky kernel: OEM ID: DELL Product ID: WS 620 APIC at: 0xFEE00000
Oct 8 06:48:42 porky kernel: I/O APIC #2 Version 32 at 0xFEC00000.
Oct 8 06:48:42 porky kernel: Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 8 06:48:42 porky kernel: Processors: 2
Oct 8 06:48:42 porky portmap: portmap startup succeeded
Oct 8 06:48:42 porky kernel: Built 1 zonelists
Oct 8 06:48:42 porky kernel: Initializing CPU#0
Oct 8 06:48:43 porky kernel: Kernel command line: ro root=LABEL=/ rhgb quiet noapic
Oct 8 06:48:43 porky kernel: (swapper/0): new 196391 us maximum-latency critical section.
Oct 8 06:48:43 porky kernel: => started at: <start_kernel+0x48/0x1e0>
Oct 8 06:48:43 porky kernel: => ended at: <cond_resched+0x25/0x80>
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky kernel: [<c0137952>] check_preempt_timing+0x162/0x200
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky rpc.statd[2435]: Version 1.0.6 Starting
Oct 8 06:48:43 porky kernel: [<c0138e58>] register_cpu_notifier+0x18/0x60
Oct 8 06:48:43 porky kernel: [<c0133688>] rcu_cpu_notify+0x38/0x40
Oct 8 06:48:43 porky kernel: [<c0381d0d>] rcu_init+0x6d/0x80
Oct 8 06:48:43 porky kernel: [<c037097c>] start_kernel+0xbc/0x1e0
Oct 8 06:48:43 porky nfslock: rpc.statd startup succeeded
Oct 8 06:48:43 porky kernel: [<c0370440>] unknown_bootoption+0x0/0x190
Oct 8 06:48:43 porky kernel: PID hash table entries: 2048 (order: 11, 32768 bytes)
Oct 8 06:48:43 porky kernel: (swapper/0): new 205265 us maximum-latency critical section.
Oct 8 06:48:43 porky kernel: => started at: <cond_resched+0x25/0x80>
Oct 8 06:48:43 porky kernel: => ended at: <cond_resched+0x25/0x80>
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky kernel: [<c0137952>] check_preempt_timing+0x162/0x200
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c0138e58>] register_cpu_notifier+0x18/0x60
Oct 8 06:48:43 porky kernel: [<c012b21b>] timer_cpu_notify+0x2b/0x30
Oct 8 06:48:43 porky kernel: [<c03819d5>] init_timers+0x35/0x60
Oct 8 06:48:43 porky kernel: [<c037098b>] start_kernel+0xcb/0x1e0
Oct 8 06:48:43 porky kernel: [<c0370440>] unknown_bootoption+0x0/0x190
Oct 8 06:48:43 porky kernel: Detected 931.130 MHz processor.
Oct 8 06:48:43 porky kernel: Using tsc for high-res timesource
Oct 8 06:48:43 porky kernel: (swapper/0): new 502992 us maximum-latency critical section.
Oct 8 06:48:43 porky kernel: => started at: <cond_resched+0x25/0x80>
Oct 8 06:48:43 porky kernel: => ended at: <cond_resched+0x25/0x80>
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky kernel: [<c0137952>] check_preempt_timing+0x162/0x200
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:43 porky kernel: [<c0137a38>] touch_preempt_timing+0x48/0x50
Oct 8 06:48:43 porky rpcidmapd: rpc.idmapd startup succeeded
Oct 8 06:48:43 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:44 porky kernel: [<c02b67b5>] cond_resched+0x25/0x80
Oct 8 06:48:44 porky kernel: [<c01212fb>] acquire_console_sem+0x2b/0x60
Oct 8 06:48:44 porky kernel: [<c038a4e3>] con_init+0x13/0x2b0
Oct 8 06:48:44 porky kernel: [<c0114df0>] mcount+0x14/0x18
Oct 8 06:48:44 porky kernel: [<c0389a12>] console_init+0x42/0x50
Oct 8 06:48:44 porky kernel: [<c037099a>] start_kernel+0xda/0x1e0
Oct 8 06:48:44 porky kernel: [<c0370440>] unknown_bootoption+0x0/0x190
Oct 8 06:48:44 porky kernel: Console: colour VGA+ 80x25
Oct 8 06:48:44 porky random: Initializing random number generator: succeeded
Oct 8 06:48:44 porky kernel: Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Oct 8 06:48:44 porky kernel: Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Oct 8 06:48:44 porky kernel: Memory: 513384k/523896k available (1762k kernel code, 9892k reserved, 725k data, 284k init, 0k highmem)
Oct 8 06:48:44 porky kernel: Checking if this processor honours the WP bit even in supervisor mode... Ok.
Oct 8 06:48:44 porky kernel: Security Scaffold v1.0.0 initialized
Oct 8 06:48:44 porky kernel: Capability LSM initialized
Oct 8 06:48:44 porky kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Oct 8 06:48:44 porky rc: Starting pcmcia: succeeded
Oct 8 06:48:44 porky kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Oct 8 06:48:44 porky kernel: CPU: L2 cache: 256K
Oct 8 06:48:44 porky kernel: Intel machine check architecture supported.
Oct 8 06:48:44 porky kernel: Intel machine check reporting enabled on CPU#0.
Oct 8 06:48:44 porky kernel: Enabling fast FPU save and restore... done.
Oct 8 06:48:44 porky kernel: Enabling unmasked SIMD FPU exception support... done.
Oct 8 06:48:44 porky kernel: Checking 'hlt' instruction... OK.
Oct 8 06:48:44 porky kernel: CPU0: Intel Pentium III (Coppermine) stepping 06
Oct 8 06:48:44 porky kernel: per-CPU timeslice cutoff: 731.28 usecs.
Oct 8 06:48:39 porky sysctl: kernel.sysrq = 0
Oct 8 06:48:44 porky kernel: task migration cache decay timeout: 1 msecs.
Oct 8 06:48:39 porky sysctl: kernel.core_uses_pid = 1
Oct 8 06:48:44 porky kernel: Booting processor 1/1 eip 2000
Oct 8 06:48:39 porky network: Setting network parameters: succeeded
Oct 8 06:48:44 porky kernel: Initializing CPU#1
Oct 8 06:48:39 porky network: Bringing up loopback interface: succeeded
Oct 8 06:48:44 porky netfs: Mounting other filesystems: succeeded
Oct 8 06:48:44 porky kernel: CPU: L1 I cache: 16K, L1 D cache: 16K
Oct 8 06:48:44 porky kernel: CPU: L2 cache: 256K
Oct 8 06:48:44 porky kernel: Intel machine check architecture supported.
Oct 8 06:48:44 porky kernel: Intel machine check reporting enabled on CPU#1.
Oct 8 06:48:44 porky kernel: CPU1: Intel Pentium III (Coppermine) stepping 06
Oct 8 06:48:44 porky kernel: Total of 2 processors activated (3682.30 BogoMIPS).
Oct 8 06:48:44 porky kernel: checking TSC synchronization across 2 CPUs: passed.
Oct 8 06:48:44 porky kernel: ksoftirqd started up.
Oct 8 06:48:44 porky kernel: Brought up 2 CPUs
Oct 8 06:48:44 porky kernel: ksoftirqd started up.
Oct 8 06:48:44 porky kernel: checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Oct 8 06:48:44 porky kernel: Freeing initrd memory: 355k freed
Oct 8 06:48:44 porky kernel: NET: Registered protocol family 16
Oct 8 06:48:44 porky autofs: automount startup succeeded
Oct 8 06:48:44 porky kernel: PCI: PCI BIOS revision 2.10 entry at 0xfc03e, last bus=4
Oct 8 06:48:44 porky kernel: PCI: Using configuration type 1
Oct 8 06:48:44 porky kernel: mtrr: v2.0 (20020519)
Oct 8 06:48:44 porky kernel: Linux Plug and Play Support v0.97 (c) Adam Belay
Oct 8 06:48:44 porky kernel: PCI: Probing PCI hardware
Oct 8 06:48:44 porky kernel: PCI: Probing PCI hardware (bus 00)
Oct 8 06:48:44 porky kernel: PCI: Transparent bridge - 0000:00:1e.0
Oct 8 06:48:44 porky kernel: PCI: Using IRQ router PIIX/ICH [8086/2410] at 0000:00:1f.0
Oct 8 06:48:45 porky smartd[2575]: smartd version 5.21 Copyright (C) 2002-3 Bruce Allen
Oct 8 06:48:45 porky kernel: PCI: Failed to allocate mem resource #0:1000@0 for 0000:03:00.0
Oct 8 06:48:45 porky smartd[2575]: Home page is http://smartmontools.sourceforge.net/
Oct 8 06:48:45 porky kernel: apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Oct 8 06:48:45 porky smartd[2575]: Opened configuration file /etc/smartd.conf
Oct 8 06:48:45 porky kernel: apm: disabled - APM is not SMP safe.
Oct 8 06:48:45 porky smartd[2575]: Configuration file /etc/smartd.conf parsed.
Oct 8 06:48:45 porky kernel: Starting balanced_irq
Oct 8 06:48:45 porky smartd[2575]: Device: /dev/hda, opened
Oct 8 06:48:45 porky kernel: VFS: Disk quotas dquot_6.5.1
Oct 8 06:48:45 porky smartd[2575]: Device: /dev/hda, unable to read Device Identity Structure
Oct 8 06:48:45 porky kernel: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Oct 8 06:48:45 porky smartd[2575]: Unable to register ATA device /dev/hda at line 30 of file /etc/smartd.conf
Oct 8 06:48:45 porky kernel: Initializing Cryptographic API
Oct 8 06:48:45 porky smartd[2575]: Unable to register device /dev/hda (no Directive -d removable). Exiting.
Oct 8 06:48:45 porky kernel: vesafb: probe of vesafb0 failed with error -6
Oct 8 06:48:45 porky kernel: isapnp: Scanning for PnP cards...
Oct 8 06:48:45 porky smartd: smartd startup failed
Oct 8 06:48:45 porky kernel: isapnp: No Plug & Play device found
Oct 8 06:48:45 porky kernel: requesting new irq thread for IRQ8...
Oct 8 06:48:45 porky kernel: Real Time Clock Driver v1.12
Oct 8 06:48:45 porky kernel: requesting new irq thread for IRQ12...
Oct 8 06:48:45 porky kernel: serio: i8042 AUX port at 0x60,0x64 irq 12
Oct 8 06:48:45 porky kernel: serio: i8042 KBD port at 0x60,0x64 irq 1
Oct 8 06:48:45 porky kernel: io scheduler noop registered
Oct 8 06:48:45 porky kernel: io scheduler anticipatory registered
Oct 8 06:48:45 porky kernel: io scheduler deadline registered
Oct 8 06:48:45 porky kernel: io scheduler cfq registered
Oct 8 06:48:45 porky kernel: RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Oct 8 06:48:45 porky kernel: Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Oct 8 06:48:45 porky kernel: ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Oct 8 06:48:45 porky kernel: ICH: IDE controller at PCI slot 0000:00:1f.1
Oct 8 06:48:45 porky kernel: ICH: chipset revision 2
Oct 8 06:48:45 porky kernel: ICH: not 100%% native mode: will probe irqs later
Oct 8 06:48:45 porky kernel: ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
Oct 8 06:48:45 porky kernel: ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
Oct 8 06:48:45 porky kernel: hda: SAMSUNG CD-R/RW SW-248F, ATAPI CD/DVD-ROM drive
Oct 8 06:48:45 porky kernel: requesting new irq thread for IRQ14...
Oct 8 06:48:45 porky kernel: elevator: using anticipatory as default io scheduler
Oct 8 06:48:45 porky kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Oct 8 06:48:45 porky kernel: hdc: Lite-On LTN483S 48x Max, ATAPI CD/DVD-ROM drive
Oct 8 06:48:45 porky kernel: requesting new irq thread for IRQ15...
Oct 8 06:48:45 porky kernel: ide1 at 0x170-0x177,0x376 on irq 15
Oct 8 06:48:46 porky kernel: mice: PS/2 mouse device common for all mice
Oct 8 06:48:46 porky kernel: IRQ#12 thread started up.
Oct 8 06:48:46 porky kernel: requesting new irq thread for IRQ1...
Oct 8 06:48:46 porky kernel: IRQ#1 thread started up.
Oct 8 06:48:46 porky kernel: input: AT Translated Set 2 keyboard on isa0060/serio0
Oct 8 06:48:46 porky kernel: input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
Oct 8 06:48:46 porky kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Oct 8 06:48:46 porky kernel: NET: Registered protocol family 2
Oct 8 06:48:46 porky kernel: IP: routing cache hash table of 2048 buckets, 32Kbytes
Oct 8 06:48:46 porky kernel: TCP: Hash tables configured (established 16384 bind 21845)
Oct 8 06:48:46 porky kernel: NET: Registered protocol family 1
Oct 8 06:48:46 porky kernel: NET: Registered protocol family 17
Oct 8 06:48:46 porky kernel: NET: Registered protocol family 8
Oct 8 06:48:46 porky kernel: NET: Registered protocol family 20
Oct 8 06:48:46 porky kernel: md: Autodetecting RAID arrays.
Oct 8 06:48:46 porky kernel: md: autorun ...
Oct 8 06:48:46 porky rc: Starting hpoj: succeeded
Oct 8 06:48:46 porky kernel: md: ... autorun DONE.
Oct 8 06:48:46 porky kernel: RAMDISK: Compressed image found at block 0
Oct 8 06:48:46 porky kernel: VFS: Mounted root (ext2 filesystem).
Oct 8 06:48:46 porky kernel: SCSI subsystem initialized
Oct 8 06:48:46 porky kernel: PCI: Found IRQ 10 for device 0000:04:05.0
Oct 8 06:48:46 porky kernel: PCI: Sharing IRQ 10 with 0000:00:1f.3
Oct 8 06:48:47 porky kernel: requesting new irq thread for IRQ10...
Oct 8 06:48:47 porky kernel: PCI: Found IRQ 5 for device 0000:04:05.1
Oct 8 06:48:47 porky kernel: PCI: Sharing IRQ 5 with 0000:04:0a.0
Oct 8 06:48:47 porky kernel: requesting new irq thread for IRQ5...
Oct 8 06:48:47 porky kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
Oct 8 06:48:47 porky kernel: <Adaptec aic7899 Ultra160 SCSI adapter>
Oct 8 06:48:47 porky kernel: aic7899: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Oct 8 06:48:47 porky kernel:
Oct 8 06:48:47 porky kernel: IRQ#10 thread started up.
Oct 8 06:48:47 porky kernel: (scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 8 06:48:47 porky kernel: Vendor: QUANTUM Model: ATLAS10K2-TY092L Rev: DA40
Oct 8 06:48:47 porky kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 8 06:48:48 porky kernel: scsi0:A:0:0: Tagged Queuing enabled. Depth 32
Oct 8 06:48:48 porky kernel: SCSI device sda: 17783239 512-byte hdwr sectors (9105 MB)
Oct 8 06:48:48 porky kernel: SCSI device sda: drive cache: write back
Oct 8 06:48:48 porky kernel: sda: sda1 sda2 sda3
Oct 8 06:48:48 porky kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Oct 8 06:48:48 porky kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
Oct 8 06:48:48 porky kernel: <Adaptec aic7899 Ultra160 SCSI adapter>
Oct 8 06:48:48 porky kernel: aic7899: Ultra160 Wide Channel B, SCSI Id=7, 32/253 SCBs
Oct 8 06:48:48 porky kernel:
Oct 8 06:48:48 porky kernel: IRQ#5 thread started up.
Oct 8 06:48:48 porky kernel: (scsi1:A:0): 20.000MB/s transfers (20.000MHz, offset 15)
Oct 8 06:48:48 porky kernel: Vendor: SEAGATE Model: SX118273LC Rev: 6679
Oct 8 06:48:48 porky kernel: Type: Direct-Access ANSI SCSI revision: 02
Oct 8 06:48:48 porky kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 32
Oct 8 06:48:48 porky kernel: SCSI device sdb: 35566480 512-byte hdwr sectors (18210 MB)
Oct 8 06:48:48 porky kernel: SCSI device sdb: drive cache: write through
Oct 8 06:48:48 porky kernel: sdb: sdb1
Oct 8 06:48:48 porky kernel: Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Oct 8 06:48:48 porky kernel: EXT3-fs: mounted filesystem with ordered data mode.
Oct 8 06:48:48 porky kernel: kjournald starting. Commit interval 5 seconds
Oct 8 06:48:48 porky kernel: Freeing unused kernel memory: 284k freed
Oct 8 06:48:48 porky kernel: NET: Registered protocol family 10
Oct 8 06:48:48 porky kernel: IPv6 over IPv4 tunneling driver
Oct 8 06:48:48 porky kernel: IRQ#8 thread started up.
Oct 8 06:48:48 porky kernel: usbcore: registered new driver usbfs
Oct 8 06:48:48 porky kernel: usbcore: registered new driver hub
Oct 8 06:48:48 porky kernel: USB Universal Host Controller Interface driver v2.2
Oct 8 06:48:48 porky kernel: PCI: Found IRQ 11 for device 0000:00:1f.2
Oct 8 06:48:48 porky kernel: uhci_hcd 0000:00:1f.2: Intel Corp. 82801AA USB
Oct 8 06:48:48 porky kernel: requesting new irq thread for IRQ11...
Oct 8 06:48:48 porky kernel: uhci_hcd 0000:00:1f.2: irq 11, io base 0xff80
Oct 8 06:48:48 porky kernel: uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
Oct 8 06:48:48 porky kernel: hub 1-0:1.0: USB hub found
Oct 8 06:48:48 porky kernel: hub 1-0:1.0: 2 ports detected
Oct 8 06:48:48 porky kernel: EXT3 FS on sda2, internal journal
Oct 8 06:48:48 porky kernel: device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com
Oct 8 06:48:48 porky kernel: Adding 1044216k swap on /dev/sda3. Priority:-1 extents:1
Oct 8 06:48:48 porky kernel: program scsi_unique_id is using a deprecated SCSI ioctl, please convert it to SG_IO
Oct 8 06:48:49 porky last message repeated 11 times
Oct 8 06:48:49 porky kernel: kjournald starting. Commit interval 5 seconds
Oct 8 06:48:49 porky kernel: EXT3 FS on sda1, internal journal
Oct 8 06:48:49 porky kernel: EXT3-fs: mounted filesystem with ordered data mode.
Oct 8 06:48:49 porky kernel: kjournald starting. Commit interval 5 seconds
Oct 8 06:48:49 porky kernel: EXT3 FS on sdb1, internal journal
Oct 8 06:48:49 porky kernel: EXT3-fs: mounted filesystem with ordered data mode.
Oct 8 06:48:49 porky kernel: IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
Oct 8 06:48:49 porky kernel: microcode: CPU0 already at revision 0x2 (current=0x2)
Oct 8 06:48:49 porky kernel: microcode: CPU1 already at revision 0x2 (current=0x2)
Oct 8 06:48:49 porky kernel: microcode: No suitable data for CPU0
Oct 8 06:48:49 porky kernel: microcode: No suitable data for CPU1
Oct 8 06:48:49 porky kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
Oct 8 06:48:49 porky kernel: parport0: irq 7 detected
Oct 8 06:48:49 porky kernel: Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Oct 8 06:48:49 porky kernel: Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
Oct 8 06:48:49 porky kernel: inserting floppy driver for 2.6.9-rc3-mm3-VP-T3
Oct 8 06:48:49 porky kernel: Floppy drive(s): fd0 is 1.44M
Oct 8 06:48:49 porky kernel: requesting new irq thread for IRQ6...
Oct 8 06:48:49 porky kernel: IRQ#6 thread started up.
Oct 8 06:48:49 porky kernel: FDC 0 is a National Semiconductor PC87306
Oct 8 06:48:49 porky kernel: Linux Tulip driver version 1.1.13 (May 11, 2002)
Oct 8 06:48:49 porky kernel: PCI: Found IRQ 5 for device 0000:04:0a.0
Oct 8 06:48:49 porky kernel: PCI: Sharing IRQ 5 with 0000:04:05.1
Oct 8 06:48:49 porky kernel: tulip0: EEPROM default media type Autosense.
Oct 8 06:48:49 porky kernel: tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
Oct 8 06:48:49 porky kernel: tulip0: MII transceiver #3 config 3100 status 7809 advertising 01e1.
Oct 8 06:48:49 porky kernel: eth0: Digital DS21140 Tulip rev 32 at 0xe480, 00:00:C0:7F:A0:E9, IRQ 5.
Oct 8 06:48:49 porky kernel: tulip 0000:04:0a.0: Device was removed without properly calling pci_disable_device(). This may need fixing.
Oct 8 06:48:49 porky kernel: IRQ#14 thread started up.
Oct 8 06:48:49 porky kernel: hda: ATAPI 48X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Oct 8 06:48:49 porky kernel: Uniform CD-ROM driver Revision: 3.20
Oct 8 06:48:49 porky kernel: IRQ#15 thread started up.
Oct 8 06:48:49 porky kernel: hdc: ATAPI 48X CD-ROM drive, 120kB Cache, UDMA(33)
Oct 8 06:48:49 porky kernel: ip_tables: (C) 2000-2002 Netfilter core team
Oct 8 06:48:49 porky kernel: Linux Tulip driver version 1.1.13 (May 11, 2002)
Oct 8 06:48:49 porky kernel: PCI: Found IRQ 5 for device 0000:04:0a.0
Oct 8 06:48:49 porky kernel: PCI: Sharing IRQ 5 with 0000:04:05.1
Oct 8 06:48:49 porky kernel: tulip0: EEPROM default media type Autosense.
Oct 8 06:48:49 porky kernel: tulip0: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
Oct 8 06:48:49 porky kernel: tulip0: MII transceiver #3 config 3100 status 7809 advertising 01e1.
Oct 8 06:48:49 porky kernel: eth0: Digital DS21140 Tulip rev 32 at 0xe480, 00:00:C0:7F:A0:E9, IRQ 5.
Oct 8 06:48:49 porky kernel: ip_tables: (C) 2000-2002 Netfilter core team
Oct 8 06:48:49 porky kernel: eth0: Setting full-duplex based on MII#3 link partner capability of 05e1.
Oct 8 06:48:49 porky kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
Oct 8 06:48:49 porky kernel: parport0: irq 7 detected
Oct 8 06:48:49 porky kernel: lp0: using parport0 (polling).
Oct 8 06:48:50 porky cups: cupsd startup succeeded
Oct 8 06:48:50 porky sshd: succeeded
Oct 8 06:48:50 porky xinetd: xinetd startup succeeded
Oct 8 06:48:50 porky ntpdate[2906]: step time server 192.168.36.1 offset -0.498488 sec
Oct 8 06:48:50 porky ntpd: succeeded
Oct 8 06:48:50 porky ntpd[2910]: ntpd 4.2.0@1.1161-r Thu Mar 11 11:46:39 EST 2004 (1)
Oct 8 06:48:50 porky ntpd: ntpd startup succeeded
Oct 8 06:48:50 porky ntpd[2910]: precision = 1.000 usec
Oct 8 06:48:50 porky ntpd[2910]: kernel time sync status 0040
Oct 8 06:48:50 porky ntpd[2910]: frequency initialized 16.655 PPM from /var/lib/ntp/drift
Oct 8 06:48:50 porky ntpd[2910]: configure: keyword "authenticate" unknown, line ignored
Oct 8 06:48:50 porky vsftpd: vsftpd vsftpd succeeded
Oct 8 06:48:50 porky sendmail: sendmail startup succeeded
Oct 8 06:48:50 porky sendmail: sm-client startup succeeded
Oct 8 06:48:50 porky gpm[2959]: *** info [startup.c(95)]:
Oct 8 06:48:50 porky gpm[2959]: Started gpm successfully. Entered daemon mode.
Oct 8 06:48:50 porky xinetd[2896]: xinetd Version 2.3.13 started with libwrap loadavg options compiled in.
Oct 8 06:48:50 porky xinetd[2896]: Started working: 2 available services
Oct 8 06:48:51 porky gpm[2959]: *** info [mice.c(1766)]:
Oct 8 06:48:51 porky gpm[2959]: imps2: Auto-detected intellimouse PS/2
Oct 8 06:48:51 porky gpm: gpm startup succeeded
Oct 8 06:48:51 porky crond: crond startup succeeded
Oct 8 06:48:51 porky xfs: xfs startup succeeded
Oct 8 06:48:52 porky anacron: anacron startup succeeded
Oct 8 06:48:52 porky atd: atd startup succeeded
Oct 8 06:48:52 porky readahead: Starting background readahead:
Oct 8 06:48:52 porky rc: Starting readahead: succeeded
Oct 8 06:48:53 porky messagebus: messagebus startup succeeded
Oct 8 06:48:53 porky mdmonitor: mdadm succeeded
Oct 8 06:48:53 porky mdmpd: mdmpd succeeded
next prev parent reply other threads:[~2004-10-08 14:05 UTC|newest]
Thread overview: 226+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20040903120957.00665413@mango.fruits.de>
[not found] ` <20040903100946.GA22819@elte.hu>
[not found] ` <20040903123139.565c806b@mango.fruits.de>
2004-09-03 10:32 ` lockup with voluntary preempt R0 and VP, KP, etc, disabled Ingo Molnar
2004-09-03 11:59 ` Florian Schmidt
2004-09-03 11:55 ` Ingo Molnar
2004-09-03 13:01 ` Florian Schmidt
2004-09-03 12:04 ` Florian Schmidt
2004-09-03 12:08 ` Florian Schmidt
2004-09-03 18:28 ` Lee Revell
2004-09-03 18:54 ` Florian Schmidt
2004-09-03 18:52 ` Lee Revell
2004-09-03 19:06 ` K.R. Foley
2004-09-04 19:51 ` [patch] voluntary-preempt-2.6.9-rc1-bk4-R4 Ingo Molnar
2004-09-05 14:02 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R5 Ingo Molnar
2004-09-05 16:07 ` Matt Heler
2004-09-05 18:16 ` Lee Revell
2004-09-05 19:12 ` Ingo Molnar
2004-09-05 21:03 ` Lee Revell
2004-09-06 6:30 ` Ingo Molnar
2004-09-06 7:44 ` Lee Revell
2004-09-07 3:17 ` K.R. Foley
2004-09-06 11:06 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R6 Ingo Molnar
2004-09-06 11:48 ` Rafael J. Wysocki
2004-09-06 12:25 ` Alexander Nyberg
2004-09-06 12:29 ` Ingo Molnar
2004-09-07 9:26 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R7 Ingo Molnar
2004-09-07 11:57 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R8 Ingo Molnar
2004-09-07 14:50 ` Alexander Nyberg
2004-09-07 15:04 ` Ingo Molnar
2004-09-07 15:29 ` Alexander Nyberg
2004-09-07 19:56 ` Rafael J. Wysocki
2004-09-07 22:59 ` Lee Revell
2004-09-08 8:20 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R9 Ingo Molnar
2004-09-08 9:46 ` Rafael J. Wysocki
2004-09-08 9:56 ` Ingo Molnar
2004-09-08 22:37 ` Lee Revell
2004-09-09 6:17 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-S0 Ingo Molnar
2004-09-09 19:30 ` Lee Revell
2004-09-09 20:23 ` Lee Revell
2004-09-19 12:26 ` [patch] voluntary-preempt-2.6.9-rc2-mm1-S1 Ingo Molnar
2004-09-19 17:05 ` Felipe Alfaro Solana
2004-09-20 17:14 ` K.R. Foley
2004-09-20 19:48 ` Ingo Molnar
2004-09-21 2:25 ` K.R. Foley
2004-09-20 19:47 ` Magnus Määttä
2004-09-21 2:07 ` BKL backtraces - was: " K.R. Foley
2004-09-21 7:18 ` Ingo Molnar
2004-09-21 7:44 ` [patch] voluntary-preempt-2.6.9-rc2-mm1-S2 Ingo Molnar
2004-09-21 18:51 ` K.R. Foley
2004-09-22 10:33 ` [patch] voluntary-preempt-2.6.9-rc2-mm1-S3 Ingo Molnar
2004-09-22 15:07 ` K.R. Foley
2004-09-22 17:16 ` Lee Revell
2004-09-22 17:40 ` K.R. Foley
2004-09-22 19:45 ` Ingo Molnar
2004-09-22 17:09 ` K.R. Foley
2004-09-22 19:08 ` Lee Revell
2004-09-23 1:13 ` Lee Revell
2004-09-23 12:28 ` [patch] voluntary-preempt-2.6.9-rc2-mm1-S4 Ingo Molnar
2004-09-23 12:57 ` Norberto Bensa
2004-09-23 13:01 ` Ingo Molnar
2004-09-23 13:07 ` Ingo Molnar
2004-09-23 13:09 ` Ingo Molnar
2004-09-23 16:46 ` Norberto Bensa
2004-09-23 17:13 ` Norberto Bensa
2004-09-23 18:20 ` Ingo Molnar
2004-09-23 13:35 ` Rui Nuno Capela
2004-09-23 13:40 ` Ingo Molnar
2004-09-23 16:23 ` Rui Nuno Capela
2004-09-23 18:07 ` Rui Nuno Capela
2004-09-24 12:43 ` OHCI_QUIRK_INITRESET (was: 2.6.9-rc2-mm2 ohci_hcd doesn't work) Rui Nuno Capela
2004-09-24 12:55 ` Ingo Molnar
2004-09-24 14:00 ` Rui Nuno Capela
2004-09-24 16:16 ` Bjorn Helgaas
2004-09-25 23:37 ` David Brownell
2004-09-26 13:09 ` Rui Nuno Capela
2004-09-27 15:11 ` Bjorn Helgaas
2004-09-23 21:12 ` [patch] voluntary-preempt-2.6.9-rc2-mm3-S5 Ingo Molnar
2004-09-24 0:32 ` Rui Nuno Capela
2004-09-24 2:22 ` K.R. Foley
2004-09-24 3:30 ` K.R. Foley
2004-09-24 7:40 ` Ingo Molnar
2004-09-24 11:05 ` K.R. Foley
2004-09-24 11:45 ` Ingo Molnar
2004-09-24 7:44 ` [patch] voluntary-preempt-2.6.9-rc2-mm3-S6 Ingo Molnar
2004-09-28 0:05 ` [patch] voluntary-preempt-2.6.9-rc2-mm4-S7 Ingo Molnar
2004-09-28 20:17 ` Rui Nuno Capela
2004-09-28 21:03 ` Rui Nuno Capela
2004-09-28 21:46 ` Rui Nuno Capela
2004-09-28 22:01 ` Matt Heler
2004-09-29 17:43 ` Lee Revell
2004-09-29 18:40 ` Lee Revell
2004-09-29 20:30 ` Ingo Molnar
2004-09-29 20:34 ` Lee Revell
2004-10-02 3:02 ` Lee Revell
2004-10-02 9:50 ` Ingo Molnar
2004-10-03 2:01 ` Lee Revell
2004-10-03 2:14 ` Lee Revell
2004-10-03 2:19 ` Lee Revell
2004-10-03 20:08 ` Ingo Molnar
2004-10-03 6:37 ` Lee Revell
2004-10-03 6:50 ` Lee Revell
2004-10-03 7:06 ` Lee Revell
2004-10-03 19:57 ` Ingo Molnar
2004-10-04 0:53 ` Lee Revell
2004-10-04 10:17 ` Ingo Molnar
2004-10-04 17:20 ` Lee Revell
2004-10-03 20:05 ` Ingo Molnar
2004-10-03 21:09 ` [patch] voluntary-preempt-2.6.9-rc3-mm1-S8 Ingo Molnar
2004-10-04 21:53 ` [patch] voluntary-preempt-2.6.9-rc3-mm1-S9 Ingo Molnar
2004-10-05 0:31 ` Lee Revell
2004-10-05 0:56 ` Florian Schmidt
2004-10-05 0:45 ` Lee Revell
2004-10-05 0:38 ` Andrew Rodland
2004-10-05 1:19 ` Rui Nuno Capela
2004-10-05 5:32 ` Peter Williams
2004-10-05 6:38 ` Ingo Molnar
2004-10-05 1:42 ` Florian Schmidt
2004-10-05 2:05 ` Florian Schmidt
2004-10-05 3:09 ` Andrew Rodland
2004-10-05 10:24 ` Florian Schmidt
2004-10-05 7:02 ` [patch] voluntary-preempt-2.6.9-rc3-mm2-T0 Ingo Molnar
2004-10-05 11:11 ` Rui Nuno Capela
2004-10-05 11:17 ` Ingo Molnar
2004-10-05 12:07 ` Hugh Dickins
2004-10-05 11:12 ` Florian Schmidt
2004-10-05 11:03 ` Ingo Molnar
2004-10-05 11:14 ` Rui Nuno Capela
2004-10-05 11:16 ` Ingo Molnar
2004-10-05 13:47 ` [patch] voluntary-preempt-2.6.9-rc3-mm2-T1 Ingo Molnar
2004-10-05 16:37 ` Rui Nuno Capela
2004-10-05 18:42 ` Ingo Molnar
2004-10-05 19:38 ` Rui Nuno Capela
2004-10-05 19:44 ` Ingo Molnar
2004-10-05 20:01 ` Rui Nuno Capela
2004-10-06 0:12 ` Lee Revell
2004-10-06 7:51 ` Ingo Molnar
2004-10-07 10:52 ` [patch] voluntary-preempt-2.6.9-rc3-mm3-T3 Ingo Molnar
[not found] ` <20041007134116.3e53b239.h.mth@web.de>
2004-10-07 11:44 ` Ingo Molnar
2004-10-07 12:08 ` Hanno Meyer-Thurow
2004-10-07 12:16 ` Rui Nuno Capela
2004-10-07 13:53 ` Rui Nuno Capela
2004-10-07 14:13 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Con Kolivas
2004-10-07 23:26 ` [patch] voluntary-preempt-2.6.9-rc3-mm3-T3 Rui Nuno Capela
2004-10-08 5:36 ` Lee Revell
2004-10-08 6:49 ` Con Kolivas
2004-10-08 18:05 ` Lee Revell
2004-10-08 7:06 ` Ingo Molnar
2004-10-08 7:36 ` Peter Williams
2004-10-08 17:27 ` Lee Revell
2004-10-07 17:55 ` K.R. Foley
2004-10-07 20:29 ` K.R. Foley
2004-10-07 21:55 ` Ingo Molnar
2004-10-08 1:41 ` K.R. Foley
2004-10-08 7:02 ` Ingo Molnar
2004-10-08 14:03 ` K.R. Foley [this message]
2004-10-08 14:28 ` Ingo Molnar
2004-10-08 21:14 ` Lee Revell
2004-10-08 23:11 ` Lee Revell
2004-10-09 4:16 ` Lee Revell
2004-10-09 4:57 ` Lee Revell
2004-10-09 5:09 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Con Kolivas
2004-10-09 5:21 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Lee Revell
2004-10-09 5:23 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Con Kolivas
2004-10-09 5:31 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Lee Revell
2004-10-09 5:34 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Con Kolivas
2004-10-09 5:50 ` Preemption model (was Re: voluntary-preempt-2.6.9-rc3-mm3-T3) Lee Revell
2004-10-09 5:53 ` Con Kolivas
2004-10-09 10:46 ` voluntary-preempt-2.6.9-rc3-mm3-T3 Ingo Molnar
2004-10-09 13:21 ` voluntary-preempt-2.6.9-rc3-mm3-T3 K.R. Foley
2004-10-09 18:16 ` [patch] voluntary-preempt-2.6.9-rc3-mm3-T3 Florian Schmidt
2004-10-11 14:29 ` [patch] CONFIG_PREEMPT_REALTIME, 'Fully Preemptible Kernel', VP-2.6.9-rc4-mm1-T4 Ingo Molnar
2004-10-11 17:48 ` Florian Schmidt
2004-10-11 21:22 ` Rui Nuno Capela
2004-10-11 21:37 ` Lee Revell
2004-10-12 4:30 ` [patch] voluntary-preempt-2.6.9-rc3-mm3-T3 Lee Revell
2004-10-12 9:17 ` Ingo Molnar
2004-10-13 16:52 ` Lee Revell
2004-10-13 16:48 ` Lee Revell
2004-10-08 11:16 ` [patch] voluntary-preempt-2.6.9-rc3-mm2-T1 William Lee Irwin III
2004-09-22 17:30 ` Oops in __posix_lock_file was:Re: [patch] voluntary-preempt-2.6.9-rc2-mm1-S2 K.R. Foley
2004-09-22 19:43 ` Ingo Molnar
2004-09-21 18:24 ` [patch] voluntary-preempt-2.6.9-rc2-mm1-S1 K.R. Foley
2004-09-21 19:21 ` Ingo Molnar
2004-09-21 19:37 ` K.R. Foley
2004-09-08 6:56 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R6 Lee Revell
2004-09-09 19:29 ` Ingo Molnar
2004-09-09 19:33 ` Lee Revell
2004-09-09 20:43 ` Lee Revell
2004-09-09 20:51 ` Ingo Molnar
2004-09-09 21:03 ` Scott Wood
2004-09-09 20:05 ` Andrew Morton
2004-09-09 20:09 ` Alan Cox
2004-09-09 21:28 ` Andrew Morton
2004-09-09 22:45 ` William Lee Irwin III
2004-09-09 22:11 ` Alan Cox
2004-09-09 23:20 ` William Lee Irwin III
2004-09-10 13:28 ` Ingo Molnar
2004-09-10 14:28 ` Paolo Ciarrocchi
2004-09-10 16:45 ` Lee Revell
2004-09-10 22:54 ` Lee Revell
2004-09-11 0:21 ` K.R. Foley
2004-09-09 20:13 ` Lee Revell
2004-09-22 0:17 ` William Lee Irwin III
2004-09-07 22:55 ` [patch] voluntary-preempt-2.6.9-rc1-bk12-R5 Lee Revell
2004-09-07 23:13 ` Lee Revell
2004-09-07 23:58 ` Rui Nuno Capela
2004-09-08 8:23 ` Ingo Molnar
2004-09-08 8:31 ` Ingo Molnar
2004-09-09 11:09 ` Rui Nuno Capela
2004-09-15 1:16 ` Lee Revell
2004-09-15 9:29 ` Rui Nuno Capela
2004-09-15 9:38 ` Ingo Molnar
2004-09-15 9:53 ` Rui Nuno Capela
2004-09-15 10:00 ` Ingo Molnar
2004-09-15 10:35 ` Rui Nuno Capela
2004-09-25 19:26 ` Lee Revell
2004-09-25 20:38 ` Ingo Molnar
2004-09-25 20:40 ` Lee Revell
2004-09-25 20:50 ` Duncan Sands
2004-09-25 23:54 ` Lee Revell
2004-09-26 13:42 ` Rui Nuno Capela
2004-09-08 8:46 ` Rui Nuno Capela
2004-09-08 8:52 ` Ingo Molnar
2004-09-05 14:49 ` [patch] voluntary-preempt-2.6.9-rc1-bk4-R4 Florian Schmidt
2004-09-05 14:53 ` K.R. Foley
2004-10-07 16:55 [patch] voluntary-preempt-2.6.9-rc3-mm3-T3 Mark_H_Johnson
2004-10-08 17:07 Mark_H_Johnson
2004-10-08 23:48 Sid Boyce
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=41669E2D.6060705@cybsft.com \
--to=kr@cybsft.com \
--cc=Mark_H_Johnson@raytheon.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=mista.tapas@gmx.net \
--cc=nando@ccrma.Stanford.EDU \
--cc=rlrevell@joe-job.com \
--cc=rncbc@rncbc.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome