Linux version 2.6.17-rc2 (rene@7ixe4) (gcc version 4.0.3) #5 PREEMPT Sun May 21 22:00:57 CEST 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002fff0000 (usable)
 BIOS-e820: 000000002fff0000 - 000000002fff8000 (ACPI data)
 BIOS-e820: 000000002fff8000 - 0000000030000000 (ACPI NVS)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
767MB LOWMEM available.
On node 0 totalpages: 196592
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 192496 pages, LIFO batch:31
DMI 2.3 present.
Allocating PCI resources starting at 40000000 (gap: 30000000:cfff0000)
Built 1 zonelists
Kernel command line: auto BOOT_IMAGE=rc2 ro root=307 reboot=w
Enabling fast FPU save and restore... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0622000 soft=c0623000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 1313.741 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 776516k/786368k available (1477k kernel code, 9312k reserved, 559k data, 120k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2630.09 BogoMIPS (lpj=1315049)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c3f9ff 00000000 00000000 00000000 00000000 00000000
Enabling disabled K7/SSE Support.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0383f9ff c1c3f9ff 00000000 00000020 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Duron(tm) Processor  stepping 01
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ACPI: setting ELCR to 0400 (from 1608)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfdb71, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:05.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Power Resource [URP1] (off)
ACPI: Power Resource [URP2] (off)
ACPI: Power Resource [FDDP] (off)
ACPI: Power Resource [LPTP] (off)
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0501
pnp: ACPI device : hid PNP0401
pnp: PnP ACPI: found 10 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:01' and the driver 'system'
pnp: 00:01: ioport range 0xde00-0xde03 has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: b000-bfff
  MEM window: eee00000-efefffff
  PREFETCH window: e2c00000-e6cfffff
Machine check exception polling timer started.
io scheduler noop registered
io scheduler cfq registered (default)
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
ACPI: Power Button (CM) [PWRB]
ACPI: Thermal Zone [THRM] (30 C)
isapnp: Scanning for PnP cards...
isapnp: checksum for device 2 is not valid (0x52)
isapnp: Card 'AudioSystem EWS64'
isapnp: Card 'TerraTec ActiveRadio'
isapnp: 2 Plug & Play cards detected total
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AMD Irongate chipset
agpgart: AGP aperture is 64M @ 0xe8000000
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:01:05.0[A] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
[drm] Initialized mga 3.2.1 20051102 on minor 0
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0a.0: 3Com PCI 3c905C Tornado at f0832f80.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD7409: IDE controller at PCI slot 0000:00:07.1
AMD7409: chipset revision 7
AMD7409: not 100% native mode: will probe irqs later
AMD7409: 0000:00:07.1 (rev 07) UDMA66 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y120P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: PLEXTOR CD-R PREMIUM, ATAPI CD/DVD-ROM drive
hdd: PLEXTOR DVD-ROM PX-116A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(66)
hda: cache flushes supported
 hda: hda1 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 > hda2
hdc: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(66)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 12 (level, low) -> IRQ 12
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:09.0: irq 12, io base 0x0000da00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:09.1[B] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:09.1: irq 10, io base 0x0000dc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.4: new low speed USB device using uhci_hcd and address 3
usb 1-1.4: configuration #1 chosen from 1 choice
input: Logitech N48 as /class/input/input0
input: USB HID v1.00 Mouse [Logitech N48] on usb-0000:00:09.0-1.4
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:06' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input1
input: AT Translated Set 2 keyboard as /class/input/input2
i2c /dev entries driver
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 120k freed
Adding 1572856k swap on /dev/hda6.  Priority:-1 extents:1 across:1572856k
EXT3 FS on hda7, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda10, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hda11, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
eth0:  setting full-duplex.