-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I'm now getting a long delay on bootup on SATA-based laptops. (30 seconds +) followed by some unusual errors. attached: .config file used here. I'm copying the log by hand as none of these units have serial ports. hardware: HP/Compaq nx6310. Intel Pentium M/Yonah processor, Intel 945 control hardware (graphics,PCI,...) "hard drive" - 16G flash drive on SATA. Filesystem is encrypted - except for "/boot". (dm-crypt/aes) (skipping PM: debug as I'm not sure it helps) (also skipping USB) There's a 30 second delay before the first record (SATA link down) - and some log entries that have skipped before this... (trying again) ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x1 impl SATA mode ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part ata1: SATA max UDMA/133 cmd 0xF001E100 ctl 0x0 bmdma 0x0 irq 222 ata2: SATA max UDMA/133 cmd 0xF001E180 ctl 0x0 bmdma 0x0 irq 222 ata3: SATA max UDMA/133 cmd 0xF001E200 ctl 0x0 bmdma 0x0 irq 222 ata4: SATA max UDMA/133 cmd 0xF001E280 ctl 0x0 bmdma 0x0 irq 222 scsi0 : ahci ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: failed to IDENTIFY (INIT_DEV_PARAMS failed, err_mask=0x80) ata1: port is slow to respond, please be patient (Status 0x80) ata1: port failed to respond (30 secs, Status 0x80) ata1: COMRESET failed (device not ready) ata1: hardreset failed, retrying in 5 secs ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-6, max UDMA/33, 32503803 sectors: LBA ata1.00: ata1: dev 0 multi count 1 ata1.00: applying bridge limits ata1.00: configured for UDMA/33 scsi1: ahci ata2: SATA link down (SStatus 0 SControl 0) scsi2: ahci ata3: SATA link down (SStatus 0 SControl 0) scsi3: ahci ata4: SATA link down (SStatus 0 SControl 0) scsi4: ahci scsi 0:0:0:0 Direct-Access ATA PQI SATA DiskOnM YUAN PQ: 0 ANSI: 5 SCSI device sda: 32503803 512-byte hdwr sectors (16642 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 32503808 512-byte hdwr sectors (16642 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: Attached scsi disk_sda ICH7: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16 ICH7: chipset revision 1 ICH7: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x60a0-0x60a7, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... hda: HL-DT-STCD-RW/DVD DRIVE GCC-4244N, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 Probing IDE interface ide1... device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialized: dm-devel@redhat.com device-mapper: table: 254:3: crypt: Error allocating crypto tfm device-mapper: ioctl: error adding target to table device-mapper: ioctl: device doesn't appear to be in the dev hash table (lots more) device-mapper: table: 254:3: linear: dm-linear: Device lookup failed device-mapper: ioctl: error adding target to table (LOTS more) then it promptly fails to find the partition. (the "Error allocating crypto tfm" seems to be part of the problem) I'll gladly do anything necessary to make this work. And, while it's been a few years since I've done device driver hacking, I'm happy to return to it. (I'm just avoiding as it takes a LOT of time and this isn't the only part of my job) Next I'm trying as recent a git tree as I can find... in the hope someone has already solved it. - - Teunis -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.6 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFFgFpFbFT/SAfwLKMRAvjHAKCgGijcRC1KtcodzEuAveDrJwfMHgCgn93Q JcqqnGV7jJacTMx8UBTPEdk= =ttoL -----END PGP SIGNATURE-----