Re: [PATCH v2 1/3] SPI: Ingenic: Add support for use GPIO as chip select line.

[Zhou Yanjie <zhouyanjie@wanyeetech.com>]

Hi Paul,

On 2022/4/23 上午3:20, Paul Cercueil wrote:
> Hi Zhou,
>
> Le sam., avril 23 2022 at 03:09:41 +0800, 周琰杰 (Zhou Yanjie) 
> <zhouyanjie@wanyeetech.com> a écrit :
>> Add support for using GPIOs as chip select lines on Ingenic SoCs.
>>
>> Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
>> ---
>>
>> Notes:
>>     v1->v2:
>>     Use "device_property_read_u32()" instead
>>     "of_property_read_u32()" as Paul Cercueil's suggestion.
>>
>>  drivers/spi/spi-ingenic.c | 11 +++++++++--
>>  1 file changed, 9 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/spi/spi-ingenic.c b/drivers/spi/spi-ingenic.c
>> index 03077a7..bb512ca 100644
>> --- a/drivers/spi/spi-ingenic.c
>> +++ b/drivers/spi/spi-ingenic.c
>> @@ -380,7 +380,7 @@ static int spi_ingenic_probe(struct 
>> platform_device *pdev)
>>      struct spi_controller *ctlr;
>>      struct ingenic_spi *priv;
>>      void __iomem *base;
>> -    int ret;
>> +    int num_cs, ret;
>>
>>      pdata = of_device_get_match_data(dev);
>>      if (!pdata) {
>> @@ -416,6 +416,11 @@ static int spi_ingenic_probe(struct 
>> platform_device *pdev)
>>      if (IS_ERR(priv->flen_field))
>>          return PTR_ERR(priv->flen_field);
>>
>> +    if (device_property_read_u32(dev, "num-cs", &num_cs)) {
>> +        dev_warn(dev, "Number of chip select lines not specified.\n");
>> +        num_cs = 2;
>
> The "num-cs" property is not required in the binding, so I don't think 
> the dev_warn() is warranted. Just silently set num_cs = 2.
>

Sure.


> With this addressed:
> Reviewed-by: Paul Cercueil <paul@crapouillou.net>
>
> Cheers,
> -Paul
>
>> +    }
>> +
>>      platform_set_drvdata(pdev, ctlr);
>>
>>      ctlr->prepare_transfer_hardware = spi_ingenic_prepare_hardware;
>> @@ -429,7 +434,9 @@ static int spi_ingenic_probe(struct 
>> platform_device *pdev)
>>      ctlr->bits_per_word_mask = pdata->bits_per_word_mask;
>>      ctlr->min_speed_hz = 7200;
>>      ctlr->max_speed_hz = 54000000;
>> -    ctlr->num_chipselect = 2;
>> +    ctlr->use_gpio_descriptors = true;
>> +    ctlr->max_native_cs = 2;
>> +    ctlr->num_chipselect = num_cs;
>>      ctlr->dev.of_node = pdev->dev.of_node;
>>
>>      if (spi_ingenic_request_dma(ctlr, dev))
>> -- 
>> 2.7.4
>>
>