Re: [PATCH v2 7/7] arm64: dts: ti: k3-am68-sk: Enable DSI on DisplayPort-0

[Vignesh Raghavendra <vigneshr@ti.com>]

On 24/06/25 13:56, Jayesh Choudhary wrote:
> Enable DSI support for AM68-SK platform.
> 
> Add DT node for DSI2eDP bridge. The DSI to eDP bridge is sn65dsi86
> on the board.
> 
> Add the endpoint nodes to describe connection from:
> DSS => DSI => SN65DSI86 bridge => DisplayPort-0
> 
> Set status for all required nodes for DisplayPort-0 as 'okay'.
> 
> Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
> ---
>  .../boot/dts/ti/k3-am68-sk-base-board.dts     | 96 +++++++++++++++++++
>  1 file changed, 96 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> index 5fa70a874d7b..aef63ae2994c 100644
> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> @@ -135,6 +135,35 @@ transceiver4: can-phy3 {
>  		max-bitrate = <5000000>;
>  	};
>  
> +	edp0_refclk: clock-edp0-refclk {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <19200000>;
> +	};
> +
> +	dp0_pwr_3v3: fixedregulator-dp0-pwr {

use std node name: regulator-...

> +		compatible = "regulator-fixed";
> +		regulator-name = "dp0-pwr";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;     /*P0 - DP0_3V3 _EN */
> +		enable-active-high;
> +		regulator-always-on;
> +	};
> +
> +	dp0: dp0-connector {
> +		compatible = "dp-connector";
> +		label = "DP0";
> +		type = "full-size";
> +		dp-pwr-supply = <&dp0_pwr_3v3>;
> +
> +		port {
> +			dp0_connector_in: endpoint {
> +				remote-endpoint = <&dp0_out>;
> +			};
> +		};
> +	};
> +
>  	connector-hdmi {
>  		compatible = "hdmi-connector";
>  		label = "hdmi";
> @@ -605,6 +634,39 @@ exp2: gpio@20 {
>  		gpio-line-names = "HDMI_PDn","HDMI_LS_OE",
>  				  "DP0_3V3_EN","eDP_ENABLE";
>  	};
> +
> +	dsi_edp_bridge: dsi-edp-bridge@2c {
> +		compatible = "ti,sn65dsi86";
> +		reg = <0x2c>;
> +		clock-names = "refclk";
> +		clocks = <&edp0_refclk>;
> +		enable-gpios = <&exp2 3 GPIO_ACTIVE_HIGH>;
> +		vpll-supply = <&vsys_io_1v8>;
> +		vccio-supply = <&vsys_io_1v8>;
> +		vcca-supply = <&vsys_io_1v2>;
> +		vcc-supply = <&vsys_io_1v2>;
> +
> +		dsi_edp_bridge_ports: ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				dp0_in: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +
> +				dp0_out: endpoint {
> +					remote-endpoint = <&dp0_connector_in>;
> +				};
> +			};
> +		};
> +	};
>  };
>  
>  &main_sdhci1 {
> @@ -699,6 +761,15 @@ dpi_out0: endpoint {
>  			remote-endpoint = <&tfp410_in>;
>  		};
>  	};
> +
> +	/* DSI */
> +	port@2 {
> +		reg = <2>;
> +
> +		dpi0_out: endpoint {
> +			remote-endpoint = <&dsi0_in>;
> +		};
> +	};
>  };
>  
>  &serdes_ln_ctrl {
> @@ -756,3 +827,28 @@ &usb0 {
>  	phys = <&serdes0_usb_link>;
>  	phy-names = "cdns3,usb3-phy";
>  };
> +
> +&dphy_tx0 {
> +	status = "okay";
> +};
> +
> +&dsi0 {
> +	status = "okay";
> +};
> +
> +&dsi0_ports {
> +
> +	port@0 {
> +		reg = <0>;
> +		dsi0_out: endpoint {
> +			remote-endpoint = <&dp0_in>;
> +		};
> +	};
> +
> +	port@1 {
> +		reg = <1>;
> +		dsi0_in: endpoint {
> +			remote-endpoint = <&dpi0_out>;
> +		};
> +	};
> +};

-- 
Regards
Vignesh
https://ti.com/opensource