From: Srihari Vijayaraghavan <sriharivijayaraghavan@yahoo.com.au>
To: lkml <linux-kernel@vger.kernel.org>
Subject: Re: [PROBLEM] 2.6.21-git oops
Date: Sun, 6 May 2007 09:22:03 +1000 (EST) [thread overview]
Message-ID: <4968.12298.qm@web52606.mail.re2.yahoo.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 940 bytes --]
[Sorry to reply to my own email, but I had some good development on this
problem]
--- Srihari Vijayaraghavan <sriharivijayaraghavan@yahoo.com.au> wrote:
> Here's the first one (there a couple following this;
> the complete dmesg is at the bottom of this email):
It turns out the system is no go with 4 GB of RAM (4 * 1 GB modules): system
instability & SATA controller doesn't detect the drives (as I reported to
linux-ide:
http://www.mail-archive.com/linux-ide@vger.kernel.org/msg06174.html).
With only 2 GB of RAM (with either pairs), system is very stable (surviving
many parallel kernel compiles for over 3 times longer than that of 4 GB), and
it detects & works fine with the SATA drives also.
Any advice on getting all of 4 GB to work reliably with SATA also?
Thanks
PS: Here's a dmesg of the all stably working 2 GB system, & the oopsy one with
4 GB.
Send instant messages to your online friends http://au.messenger.yahoo.com
[-- Attachment #2: 569209996-dmesg-2.6.21.1-2gigs --]
[-- Type: application/octet-stream, Size: 14199 bytes --]
Linux version 2.6.21.1 (hari@fedora7) (gcc version 4.1.2 20070424 (Red Hat 4.1.2-11)) #10 SMP Sat May 5 15:22:12 EST 2007
Command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
BIOS-e820: 000000007fee0000 - 000000007fee3000 (ACPI NVS)
BIOS-e820: 000000007fee3000 - 000000007fef0000 (ACPI data)
BIOS-e820: 000000007fef0000 - 000000007ff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F80A0, 0024 (r2 ATI )
ACPI: XSDT 7FEE30C0, 0044 (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: FACP 7FEE83C0, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: DSDT 7FEE3240, 511F (r1 ATI ASUSACPI 1000 MSFT 3000000)
ACPI: FACS 7FEE0000, 0040
ACPI: SSDT 7FEE85C0, 02CC (r1 PTLTD POWERNOW 1 LTP 1)
ACPI: MCFG 7FEE8980, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: APIC 7FEE8500, 0068 (r1 ATI ASUSACPI 42302E31 AWRD 0)
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007fee0000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000007fee0000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 524000
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 80000000 (gap: 7ff00000:60100000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 34112 bytes of per cpu data
Built 1 zonelists. Total pages: 514683
Kernel command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2799.977 MHz processor.
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 30
... MAX_LOCKDEP_KEYS: 2048
... CLASSHASH_SIZE: 1024
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
memory used by lock dependency info: 1648 kB
per task-struct memory footprint: 1680 bytes
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Checking aperture...
CPU 0: aperture @ d3ac000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 2052280k/2096000k available (2291k kernel code, 43332k reserved, 1295k data, 320k init)
Calibrating delay using timer specific routine.. 5602.66 BogoMIPS (lpj=2801334)
Security Framework v1.0.0 initialized
SELinux: Initializing.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
lockdep: not fixing up alternatives.
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12499905
Detected 12.499 MHz APIC timer.
lockdep: not fixing up alternatives.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5598.98 BogoMIPS (lpj=2799494)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03
Brought up 2 CPUs
migration_cost=36
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:01: ioport range 0x4100-0x411f has been reserved
pnp: 00:01: ioport range 0x228-0x22f has been reserved
pnp: 00:01: ioport range 0x40b-0x40b has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: ioport range 0xc00-0xc01 has been reserved
pnp: 00:01: ioport range 0xc14-0xc14 has been reserved
pnp: 00:01: ioport range 0xc50-0xc52 has been reserved
pnp: 00:01: ioport range 0xc6c-0xc6d has been reserved
pnp: 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0a: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:0a: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:0a: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0a: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:02.0
Time: acpi_pm clocksource has been installed.
IO window: d000-dfff
MEM window: fdc00000-fdcfffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: fdb00000-fdbfffff
PREFETCH window: fdf00000-fdffffff
PCI: Bridge: 0000:00:14.4
IO window: c000-cfff
MEM window: fde00000-fdefffff
PREFETCH window: fdd00000-fddfffff
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 65536 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3033k freed
audit: initializing netlink socket (disabled)
audit(1178377840.600:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler cfq registered (default)
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x14 (2800 MHz), vid 0x8
powernow-k8: 1 : fid 0x12 (2600 MHz), vid 0xa
powernow-k8: 2 : fid 0x10 (2400 MHz), vid 0xc
powernow-k8: 3 : fid 0xe (2200 MHz), vid 0xe
powernow-k8: 4 : fid 0xc (2000 MHz), vid 0x10
powernow-k8: 5 : fid 0xa (1800 MHz), vid 0x10
powernow-k8: 6 : fid 0x2 (1000 MHz), vid 0x12
Freeing unused kernel memory: 320k freed
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1
drivers/usb/input/hid-core.c: Fixing up Logitech S510 report descriptor
input: Logitech USB Receiver as /class/input/input1
input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb 2-1: USB disconnect, address 2
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 10 ports detected
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
ata1: PATA max UDMA/100 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x000000000001f900 irq 14
ata2: PATA max UDMA/100 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x000000000001f908 irq 15
scsi0 : pata_atiixp
usb 2-1: new low speed USB device using ohci_hcd and address 3
ata1.00: ATA-6: ST3120026A, 3.06, max UDMA/100
ata1.00: 234435439 sectors, multi 1: LBA48
ata1.01: ATAPI, max UDMA/33
ata1.00: configured for UDMA/100
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1
drivers/usb/input/hid-core.c: Fixing up Logitech S510 report descriptor
input: Logitech USB Receiver as /class/input/input3
input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1
ata1.01: configured for UDMA/33
scsi1 : pata_atiixp
scsi 0:0:0:0: Direct-Access ATA ST3120026A 3.06 PQ: 0 ANSI: 5
SCSI device sda: 234435439 512-byte hdwr sectors (120031 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 234435439 512-byte hdwr sectors (120031 MB)
sda: Write Protect is off
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 >
sd 0:0:0:0: Attached scsi disk sda
scsi 0:0:1:0: CD-ROM HL-DT-ST DVDRAM GSA-4163B A102 PQ: 0 ANSI: 5
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1178377847.207:2): enforcing=1 old_enforcing=0 auid=4294967295
audit(1178377847.508:3): policy loaded auid=4294967295
raid0: looking at sdb
raid0: comparing sdb(244198464) with sdb(244198464)
raid0: END
raid0: ==> UNIQUE
raid0: 1 zones
raid0: looking at sdc
raid0: comparing sdc(244198464) with sdb(244198464)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: done.
raid0 : md_size is 488396928 blocks.
raid0 : conf->hash_spacing is 488396928 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
[-- Attachment #3: 2887524220-oops2-mm-2.6.21.1-libata-4gigs --]
[-- Type: application/octet-stream, Size: 20256 bytes --]
Linux version 2.6.21.1 (hari@fedora7) (gcc version 4.1.2 20070424 (Red Hat 4.1.2-11)) #8 SMP Sat May 5 12:27:53 EST 2007
Command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0 pci=nomsi
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000dfee0000 (usable)
BIOS-e820: 00000000dfee0000 - 00000000dfee3000 (ACPI NVS)
BIOS-e820: 00000000dfee3000 - 00000000dfef0000 (ACPI data)
BIOS-e820: 00000000dfef0000 - 00000000dff00000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
end_pfn_map = 1179648
DMI 2.4 present.
ACPI: RSDP 000F80A0, 0024 (r2 ATI )
ACPI: XSDT DFEE30C0, 0044 (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: FACP DFEE83C0, 00F4 (r3 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: DSDT DFEE3240, 511F (r1 ATI ASUSACPI 1000 MSFT 3000000)
ACPI: FACS DFEE0000, 0040
ACPI: SSDT DFEE85C0, 02CC (r1 PTLTD POWERNOW 1 LTP 1)
ACPI: MCFG DFEE8980, 003C (r1 ATI ASUSACPI 42302E31 AWRD 0)
ACPI: APIC DFEE8500, 0068 (r1 ATI ASUSACPI 42302E31 AWRD 0)
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 0000000120000000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-0000000120000000
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1179648
early_node_map[3] active PFN ranges
0: 0 -> 159
0: 256 -> 917216
0: 1048576 -> 1179648
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x4008
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to physical flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Nosave address range: 00000000dfee0000 - 00000000dfee3000
Nosave address range: 00000000dfee3000 - 00000000dfef0000
Nosave address range: 00000000dfef0000 - 00000000dff00000
Nosave address range: 00000000dff00000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at f1000000 (gap: f0000000:ec00000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 42048 bytes of per cpu data
Built 1 zonelists. Total pages: 1020593
Kernel command line: ro root=LABEL=/1234 console=ttyS0,115200 console=tty0 pci=nomsi
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2800.013 MHz processor.
Console: colour VGA+ 80x25
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 30
... MAX_LOCKDEP_KEYS: 2048
... CLASSHASH_SIZE: 1024
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
memory used by lock dependency info: 1648 kB
per task-struct memory footprint: 1680 bytes
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 8000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Memory: 4018416k/4718592k available (2349k kernel code, 174348k reserved, 1356k data, 328k init)
Calibrating delay using timer specific routine.. 5602.58 BogoMIPS (lpj=2801292)
Security Framework v1.0.0 initialized
SELinux: Initializing.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
lockdep: not fixing up alternatives.
ACPI: Core revision 20070126
Using local APIC timer interrupts.
result 12500065
Detected 12.500 MHz APIC timer.
lockdep: not fixing up alternatives.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5598.98 BogoMIPS (lpj=2799494)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping 03
Brought up 2 CPUs
migration_cost=297
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000 - efffffff
PCI: No mmconfig possible on device 00:18
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 *11)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: 00:01: ioport range 0x4100-0x411f has been reserved
pnp: 00:01: ioport range 0x228-0x22f has been reserved
pnp: 00:01: ioport range 0x40b-0x40b has been reserved
pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
pnp: 00:01: ioport range 0xc00-0xc01 has been reserved
pnp: 00:01: ioport range 0xc14-0xc14 has been reserved
pnp: 00:01: ioport range 0xc50-0xc52 has been reserved
pnp: 00:01: ioport range 0xc6c-0xc6d has been reserved
pnp: 00:09: iomem range 0xe0000000-0xefffffff could not be reserved
pnp: 00:0a: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:0a: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:0a: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0a: iomem range 0xfc000-0xfffff could not be reserved
PCI: Bridge: 0000:00:02.0
Time: acpi_pm clocksource has been installed.
IO window: d000-dfff
MEM window: fdc00000-fdcfffff
PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:07.0
IO window: e000-efff
MEM window: fdb00000-fdbfffff
PREFETCH window: fdf00000-fdffffff
PCI: Bridge: 0000:00:14.4
IO window: c000-cfff
MEM window: fde00000-fdefffff
PREFETCH window: fdd00000-fddfffff
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 65536 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 3033k freed
audit: initializing netlink socket (disabled)
audit(1178335090.223:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler cfq registered (default)
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (40 C)
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SB600_PATA: IDE controller at PCI slot 0000:00:14.1
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 16
SB600_PATA: chipset revision 0
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf900-0xf907, BIOS settings: hda:pio, hdb:pio
hda: ST3120026A, ATA DISK drive
hdb: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 512KiB
hda: Host Protected Area detected.
current capacity is 234435439 sectors (120030 MB)
native capacity is 234441648 sectors (120034 MB)
hda: Host Protected Area disabled.
hda: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 >
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x14 (2800 MHz), vid 0x8
powernow-k8: 1 : fid 0x12 (2600 MHz), vid 0xa
powernow-k8: 2 : fid 0x10 (2400 MHz), vid 0xc
powernow-k8: 3 : fid 0xe (2200 MHz), vid 0xe
powernow-k8: 4 : fid 0xc (2000 MHz), vid 0x10
powernow-k8: 5 : fid 0xa (1800 MHz), vid 0x10
powernow-k8: 6 : fid 0x2 (1000 MHz), vid 0x12
Freeing unused kernel memory: 328k freed
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe02e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 17, io mem 0xfe02d000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.2: irq 18, io mem 0xfe02c000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.3: irq 17, io mem 0xfe02b000
usb 2-1: new low speed USB device using ohci_hcd and address 2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.4: irq 18, io mem 0xfe02a000
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input0
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1
drivers/usb/input/hid-core.c: Fixing up Logitech S510 report descriptor
input: Logitech USB Receiver as /class/input/input1
input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 6
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 19, io mem 0xfe029000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb 2-1: USB disconnect, address 2
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 10 ports detected
SCSI subsystem initialized
usb 2-1: new low speed USB device using ohci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
input: Logitech USB Receiver as /class/input/input2
input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:13.1-1
drivers/usb/input/hid-core.c: Fixing up Logitech S510 report descriptor
input: Logitech USB Receiver as /class/input/input3
input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:13.1-1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
audit(1178335097.512:2): enforcing=1 old_enforcing=0 auid=4294967295
audit(1178335097.813:3): policy loaded auid=4294967295
ata3.00: qc timeout (cmd 0xec)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x104)
general protection fault: 0000 [1] SMP
CPU 1
Modules linked in: radeon drm autofs4 it87 hwmon_vid i2c_isa sunrpc cpufreq_ondemand dm_mod video sbs i2c_ec button dock battery ac loop kvm_amd kvm snd_hda_intel snd_hda_codec snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device ide_cd cdrom snd_pcm_oss snd_mixer_oss snd_pcm r8169 i2c_piix4 i2c_core serio_raw ahci snd_timer pcspkr k8temp hwmon rtc_cmos rtc_core rtc_lib snd soundcore snd_page_alloc shpchp joydev ata_generic pata_atiixp libata sd_mod scsi_mod ext3 jbd mbcache ehci_hcd ohci_hcd
Pid: 9070, comm: cc1 Not tainted 2.6.21.1 #8
RIP: 0010:[<ffffffff802c26fe>] [<ffffffff802c26fe>] __rmqueue+0x41/0xee
RSP: 0000:ffff810092b8dc58 EFLAGS: 00010002
RAX: ffff81000000e778 RBX: ffff81000000e778 RCX: ffff810000239f48
RDX: 4d8d4cc84d8d4850 RSI: 0000000000000000 RDI: ffff81000000e500
RBP: ffff810092b8dc78 R08: 0000000000000001 R09: 0000000000000001
R10: ffffffff8020a426 R11: 0000000000000002 R12: 0000000000000000
R13: ffff810000239f00 R14: 0000000000000000 R15: 0000000000000019
FS: 00002ae828913250(0000) GS:ffff81011fc106c0(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00002ae82cc77000 CR3: 000000009ba79000 CR4: 00000000000006e0
Process cc1 (pid: 9070, threadinfo ffff810092b8c000, task ffff8100915f70c0)
Stack: ffff81011fc107c0 0000000000000286 ffff81000000e500 000000000000001a
ffff810092b8dd08 ffffffff8020a435 00000044915f7838 ffff81000000fe60
00000000915f70c0 00000040000280d2 ffff81000000fe70 0000000280748370
Call Trace:
[<ffffffff8020a435>] get_page_from_freelist+0x1c8/0x54b
[<ffffffff8020f803>] __alloc_pages+0x74/0x2dd
[<ffffffff802229f3>] alloc_page_vma+0x85/0x8e
[<ffffffff80208c10>] __handle_mm_fault+0x580/0xcd1
[<ffffffff80268047>] do_page_fault+0x38b/0x7ed
[<ffffffff80268103>] do_page_fault+0x447/0x7ed
[<ffffffff802659db>] _spin_unlock+0x26/0x2a
[<ffffffff802bb738>] audit_syscall_exit+0x2f7/0x318
[<ffffffff802654d2>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff802662bd>] error_exit+0x0/0x96
Code: 48 89 42 08 48 89 10 48 c7 41 08 00 02 20 00 48 c7 01 00 01
RIP [<ffffffff802c26fe>] __rmqueue+0x41/0xee
RSP <ffff810092b8dc58>
BUG: sleeping function called from invalid context at kernel/rwsem.c:20
in_atomic():0, irqs_disabled():1
INFO: lockdep is turned off.
irq event stamp: 25706
hardirqs last enabled at (25705): [<ffffffff80265d9e>] _spin_unlock_irqrestore+0x3f/0x47
hardirqs last disabled at (25706): [<ffffffff8020a40a>] get_page_from_freelist+0x19d/0x54b
softirqs last enabled at (25380): [<ffffffff80212885>] __do_softirq+0xda/0xe3
softirqs last disabled at (25371): [<ffffffff8025f31c>] call_softirq+0x1c/0x28
Call Trace:
[<ffffffff8020b966>] __might_sleep+0xda/0xdc
[<ffffffff802a002b>] down_read+0x1d/0x4a
[<ffffffff802b0cc4>] acct_collect+0x4c/0x19c
[<ffffffff80215c2e>] do_exit+0x1f8/0x85e
[<ffffffff8026cf7d>] kernel_math_error+0x0/0x96
[<ffffffff80266c09>] do_general_protection+0x10a/0x115
[<ffffffff802662bd>] error_exit+0x0/0x96
[<ffffffff8020a426>] get_page_from_freelist+0x1b9/0x54b
[<ffffffff802c26fe>] __rmqueue+0x41/0xee
[<ffffffff802c2739>] __rmqueue+0x7c/0xee
[<ffffffff8020a435>] get_page_from_freelist+0x1c8/0x54b
[<ffffffff8020f803>] __alloc_pages+0x74/0x2dd
[<ffffffff802229f3>] alloc_page_vma+0x85/0x8e
[<ffffffff80208c10>] __handle_mm_fault+0x580/0xcd1
[<ffffffff80268047>] do_page_fault+0x38b/0x7ed
[<ffffffff80268103>] do_page_fault+0x447/0x7ed
[<ffffffff802659db>] _spin_unlock+0x26/0x2a
[<ffffffff802bb738>] audit_syscall_exit+0x2f7/0x318
[<ffffffff802654d2>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff802662bd>] error_exit+0x0/0x96
BUG: spinlock lockup on CPU#0, cc1/9065, ffff81000000e748
Call Trace:
[<ffffffff802077f4>] _raw_spin_lock+0xd1/0xf9
[<ffffffff80265a85>] _spin_lock+0x2d/0x31
[<ffffffff8020a426>] get_page_from_freelist+0x1b9/0x54b
[<ffffffff8020f803>] __alloc_pages+0x74/0x2dd
[<ffffffff802229f3>] alloc_page_vma+0x85/0x8e
[<ffffffff80208c10>] __handle_mm_fault+0x580/0xcd1
[<ffffffff80268047>] do_page_fault+0x38b/0x7ed
[<ffffffff80268103>] do_page_fault+0x447/0x7ed
[<ffffffff802659db>] _spin_unlock+0x26/0x2a
[<ffffffff802bb738>] audit_syscall_exit+0x2f7/0x318
[<ffffffff802654d2>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff802662bd>] error_exit+0x0/0x96
BUG: spinlock lockup on CPU#1, cc1/9070, ffff81000000e748
Call Trace:
[<ffffffff802077f4>] _raw_spin_lock+0xd1/0xf9
[<ffffffff80265a85>] _spin_lock+0x2d/0x31
[<ffffffff802c28c7>] free_pages_bulk+0x2a/0x20e
[<ffffffff8020b6c0>] free_hot_cold_page+0x178/0x1a3
[<ffffffff80224b68>] __pagevec_free+0x29/0x39
[<ffffffff8020ae25>] release_pages+0x142/0x197
[<ffffffff8020e5a6>] free_pages_and_swap_cache+0x7b/0x96
[<ffffffff80207cec>] unmap_vmas+0x4c2/0x75f
[<ffffffff8023affb>] exit_mmap+0x77/0xee
[<ffffffff8023d28d>] mmput+0x46/0xb7
[<ffffffff8024201d>] exit_mm+0xe1/0xea
[<ffffffff80215c77>] do_exit+0x241/0x85e
[<ffffffff8026cf7d>] kernel_math_error+0x0/0x96
[<ffffffff80266c09>] do_general_protection+0x10a/0x115
[<ffffffff802662bd>] error_exit+0x0/0x96
[<ffffffff8020a426>] get_page_from_freelist+0x1b9/0x54b
[<ffffffff802c26fe>] __rmqueue+0x41/0xee
[<ffffffff802c2739>] __rmqueue+0x7c/0xee
[<ffffffff8020a435>] get_page_from_freelist+0x1c8/0x54b
[<ffffffff8020f803>] __alloc_pages+0x74/0x2dd
[<ffffffff802229f3>] alloc_page_vma+0x85/0x8e
[<ffffffff80208c10>] __handle_mm_fault+0x580/0xcd1
[<ffffffff80268047>] do_page_fault+0x38b/0x7ed
[<ffffffff80268103>] do_page_fault+0x447/0x7ed
[<ffffffff802659db>] _spin_unlock+0x26/0x2a
[<ffffffff802bb738>] audit_syscall_exit+0x2f7/0x318
[<ffffffff802654d2>] trace_hardirqs_on_thunk+0x35/0x37
[<ffffffff802662bd>] error_exit+0x0/0x96
next reply other threads:[~2007-05-05 23:22 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2007-05-05 23:22 Srihari Vijayaraghavan [this message]
2007-05-05 23:37 ` Michal Piotrowski
2007-05-06 1:27 ` Srihari Vijayaraghavan
-- strict thread matches above, loose matches on Subject: below --
2007-05-02 20:42 Srihari Vijayaraghavan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4968.12298.qm@web52606.mail.re2.yahoo.com \
--to=sriharivijayaraghavan@yahoo.com.au \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®