Hi! I'm not sure if i'm posting to the right place, so if i'm wrong, please forward it to the "right" people. :-) Now, on the problem. I own laptop, Dell Latitude D630 with 4Gig of ram. Installed is Ubuntu, 9.04 Desktop x86_64, with 2.6.28 kernel. I also own pcmcia network card, Edimax EP-4203DL (1gb), which is having problems. More precisely - it does not work. My first guess was that this is driver related and i did try all of them - with no success. Problem is, that when card is inserted, card is recognized and right driver is loaded, BUT, then driver reports unknown eeprom version and assigns -1 (ff:ff:ff:ff:ff:ff) as mac address. Of course, any attempt to change mac back to right or to initialize card - just fails. As the card is not there!? I get those stupid error "unable to assign address" or something from ifconfig command. After a lot of fiddling around, i did notice following line: pci_bus 0000:03: Raising subordinate bus# of parent bus (#03) from #04 to #07 After investigating a little, i found that this is related to fixup for bios bug, which incorrectly assigns bus id to pcmcia chip? This message is from code which attempts to reassign bus so card can work. But, in my case, it does not. What is very interesting is that, removing yenta_socket module and inserting it again - solves the problem!!! Here is dmesg for first insert: [ 8.036478] yenta_cardbus 0000:03:01.0: CardBus bridge found [1028:01f9] [ 8.036502] yenta_cardbus 0000:03:01.0: O2: res at 0x94/0xD4: 00/ea [ 8.036503] yenta_cardbus 0000:03:01.0: O2: enabling read prefetch/write burst [ 8.165238] yenta_cardbus 0000:03:01.0: ISA IRQ mask 0x04b8, PCI irq 19 [ 8.165241] yenta_cardbus 0000:03:01.0: Socket status: 30000006 [ 8.165244] pci_bus 0000:03: Raising subordinate bus# of parent bus (#03) from #04 to #07 [ 8.165249] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff [ 8.165251] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window: 0xf1d00000 - 0xf1dfffff [ 8.165252] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window: 0x120000000 - 0x123ffffff And this is on second insert: [ 8.680195] yenta_cardbus 0000:03:01.0: CardBus bridge found [1028:01f9] [ 8.680227] yenta_cardbus 0000:03:01.0: Preassigned resource 2 busy or not available, reconfiguring... [ 8.680235] yenta_cardbus 0000:03:01.0: Preassigned resource 3 busy or not available, reconfiguring... [ 8.680237] yenta_cardbus 0000:03:01.0: CardBus bridge, secondary bus 0000:04 [ 8.680239] yenta_cardbus 0000:03:01.0: IO window: 0x002000-0x0020ff [ 8.680244] yenta_cardbus 0000:03:01.0: IO window: 0x002400-0x0024ff [ 8.680249] yenta_cardbus 0000:03:01.0: PREFETCH window: 0xf0000000-0xf03fffff [ 8.680254] yenta_cardbus 0000:03:01.0: MEM window: 0xf0400000-0xf07fffff [ 8.680263] yenta_cardbus 0000:03:01.0: O2: res at 0x94/0xD4: 00/ea [ 8.680264] yenta_cardbus 0000:03:01.0: O2: enabling read prefetch/write burst [ 8.813294] yenta_cardbus 0000:03:01.0: ISA IRQ mask 0x0cb8, PCI irq 19 [ 8.813297] yenta_cardbus 0000:03:01.0: Socket status: 30000006 [ 8.813337] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff [ 8.813339] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window: 0xf1d00000 - 0xf1dfffff [ 8.813341] yenta_cardbus 0000:03:01.0: pcmcia: parent PCI bridge Memory window: 0x120000000 - 0x123ffffff In source, this message about subordinate buses comes from yenta_fixup_parent_bridge, and it is called from devinit method yenta_probe. So, as i see it, yenta_fixup_parent_bridge fixes problem with buses, but it is called way down after driver initialization, and effectively, driver is not aware of changed resources (pci inspecting is done BEFORE call to fixup), so - it does not work! Should not fixup be called way before, or should not initialization be restarted after something changed?? Attached are two dmesg-s: - dmesg.2.6.28-14-generic - clean boot - dmesg.2.6.28-14-generic.2 - at boot, yenta_socked is removed and then reinserted and two /proc/iomem: - proc.iomem - iomem after clean boot - proc.iomem.2 - after second boot, where yenta_socket is reinserted and, finaly two, lspci -vv: - lspci - clean boot - lspci - boot with reinserted yenta_socket Hope this will help ... :-) H.