From: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
To: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: richard@nod.at, vigneshr@ti.com, linux-mtd@lists.infradead.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] mtd: rawnand: cadence: Add support for NV-DDR interface mode
Date: Fri, 24 Oct 2025 17:47:11 +0800 [thread overview]
Message-ID: <4a6577ff-7417-4d34-a683-2402736fd9d7@altera.com> (raw)
In-Reply-To: <87bjlwrbqd.fsf@bootlin.com>
On 24/10/2025 3:38 pm, Miquel Raynal wrote:
> Hi Niravkumar,
>
> On 24/10/2025 at 15:13:06 +08, niravkumarlaxmidas.rabara@altera.com wrote:
>
>> From: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
>>
>> Add support for NV-DDR mode in the Cadence NAND controller driver.
>>
>> Signed-off-by: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
>> ---
>
> Thanks for the patch, very happy to see people implementing this
> interface!
Thanks for the review comments.
>
> [...]
>
>> + if (dll_phy_gate_open_delay > NVDDR_GATE_CFG_MIN)
>> + ie_start = NVDDR_GATE_CFG_MIN;
>
> Can you double check here? I would expect < instead of > given that you
> compare with something you named "minimum". Maybe it is legitimate, just
> warning.
I have double checked, the logic is correct. May be I shouldn't use _MIN
to avoid confusion.
In v2 I will change NVDDR_GATE_CFG_MIN to NVDDR_GATE_CFG_STD.
>
>> + else
>> + ie_start = dll_phy_gate_open_delay;
>> +
>> + dll_phy_rd_delay = ((nvddr->tDQSCK_max + board_delay) +
>> + (clk_period / 2)) / clk_period;
>> + if (dll_phy_rd_delay <= NVDDR_PHY_RD_DELAY)
>> + rd_del_sel = dll_phy_rd_delay + 2;
>> + else
>> + rd_del_sel = NVDDR_PHY_RD_DELAY_MAX;
>> +
>
> [...]
>
>> +static int
>> +cadence_nand_setup_interface(struct nand_chip *chip, int chipnr,
>> + const struct nand_interface_config *conf)
>> +{
>> + int ret = 0;
>> +
>> + if (nand_interface_is_sdr(conf)) {
>> + const struct nand_sdr_timings *sdr = nand_get_sdr_timings(conf);
>> +
>> + if (IS_ERR(sdr))
>> + return PTR_ERR(sdr);
>> +
>> + ret = cadence_nand_setup_sdr_interface(chip, sdr);
>> + } else if (chipnr >= 0) {
>
> This isn't very clear. Please make it a separate condition if you think
> you must handle this case. Otherwise you're mixing it with the SDR
> vs. NVDDR choice, and that's misleading.
Noted.
I will make a separate condition check as below in v2.
- } else if (chipnr >= 0) {
- const struct nand_nvddr_timings *nvddr =
nand_get_nvddr_timings(conf);
+ } else {
+ if (chipnr < 0)
+ return ret;
+ const struct nand_nvddr_timings *nvddr =
nand_get_nvddr_timings(conf);
>
>> + const struct nand_nvddr_timings *nvddr = nand_get_nvddr_timings(conf);
>> +
>> + if (IS_ERR(nvddr))
>> + return PTR_ERR(nvddr);
>> +
>> + ret = cadence_nand_setup_nvddr_interface(chip, nvddr);
>> + }
>> + return ret;
>> +}
>> +
>> static int cadence_nand_attach_chip(struct nand_chip *chip)
>> {
>> struct cdns_nand_ctrl *cdns_ctrl = to_cdns_nand_ctrl(chip->controller);
>
> Otherwise looks good to me!
> Miquèl
next prev parent reply other threads:[~2025-10-24 9:47 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-10-24 7:13 niravkumarlaxmidas.rabara
2025-10-24 7:38 ` Miquel Raynal
2025-10-24 9:47 ` Niravkumar L Rabara [this message]
2025-10-24 11:11 ` Miquel Raynal
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4a6577ff-7417-4d34-a683-2402736fd9d7@altera.com \
--to=niravkumarlaxmidas.rabara@altera.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mtd@lists.infradead.org \
--cc=miquel.raynal@bootlin.com \
--cc=richard@nod.at \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®