Re: [PATCH 03/10] arm64: dts: qcom: Add pm8010 pmic dtsi

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 16/11/2022 11:31, Abel Vesa wrote:
> From: Neil Armstrong <neil.armstrong@linaro.org>
> 
> Add nodes for pm8010 in separate dtsi file.
> 
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>   arch/arm64/boot/dts/qcom/pm8010.dtsi | 84 ++++++++++++++++++++++++++++
>   1 file changed, 84 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/pm8010.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/pm8010.dtsi b/arch/arm64/boot/dts/qcom/pm8010.dtsi
> new file mode 100644
> index 000000000000..0ea641e12209
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm8010.dtsi
> @@ -0,0 +1,84 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> +	thermal-zones {
> +		pm8010-m-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pm8010_m_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +
> +		pm8010-n-thermal {
> +			polling-delay-passive = <100>;
> +			polling-delay = <0>;
> +
> +			thermal-sensors = <&pm8010_n_temp_alarm>;
> +
> +			trips {
> +				trip0 {
> +					temperature = <95000>;
> +					hysteresis = <0>;
> +					type = "passive";
> +				};
> +
> +				trip1 {
> +					temperature = <115000>;
> +					hysteresis = <0>;
> +					type = "hot";
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +
> +&spmi_bus {
> +	pm8010_m: pmic@c {
> +		compatible = "qcom,pm8010", "qcom,spmi-pmic";
> +		reg = <0xc SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8010_m_temp_alarm: temp-alarm@2400 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0x2400>;
> +			interrupts = <0xc 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +	};
> +
> +	pm8010_n: pmic@d {
> +		compatible = "qcom,pm8010", "qcom,spmi-pmic";
> +		reg = <0xd SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8010_n_temp_alarm: temp-alarm@2400 {
> +			compatible = "qcom,spmi-temp-alarm";
> +			reg = <0x2400>;
> +			interrupts = <0xd 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
> +			#thermal-sensor-cells = <0>;
> +		};
> +	};
> +};