From: Joshua Crofts <crofts@kernel.org>
To: Zheng Shuhao <viennaoffh@gmail.com>, Jiri Kosina <jikos@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>,
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>,
Benjamin Tissoires <bentiss@kernel.org>,
linux-input@vger.kernel.org, linux-iio@vger.kernel.org,
linux-kernel@vger.kernel.org,
syzbot+fb951970a334aaff00ba@syzkaller.appspotmail.com
Subject: Re: [PATCH] HID: sensor-hub: Avoid holding spinlock across child iteration
Date: Fri, 20 Nov 2026 12:09:11 +0100 [thread overview]
Message-ID: <4f254948-29d5-4011-8865-c60a699d9bac@kernel.org> (raw)
In-Reply-To: <0428126d-684f-4b4c-a805-7dc3e2d56897@kernel.org>
On 20/11/2026 11:50, Joshua Crofts wrote:
> On 20/11/2026 08:56, Zheng Shuhao wrote:
>> syzbot reports a SOFTIRQ-safe -> SOFTIRQ-unsafe lock order warning during
>> sensor hub removal.
>>
>> sensor_hub_remove() currently holds sensor_data->lock while calling
>> device_for_each_child(). The child iteration enters the device core and may
>> acquire the klist lock. Since sensor_data->lock is also acquired with
>> interrupts disabled by sensor_hub_raw_event(), lockdep reports a possible
>> lock-order inversion.
>>
>> The callback only needs sensor_data->lock while checking pending.status and
>> completing pending.ready. Pass sensor_data to the callback and take the lock
>> only around that short critical section instead of holding it across
>> device_for_each_child().
>>
>> This preserves synchronization of pending.status while avoiding the lock-order
>> dependency between sensor_data->lock and the device core's klist lock.
>>
>> The syzbot report is available at:
>> https://syzkaller.appspot.com/bug?id=c7c429f6851638ece81338f90c5b29ac9c0dea1f
>>
>> Testing:
>> - Reproduced the target lockdep warning with the unmodified kernel in 3/3
>> two-CPU QEMU runs.
>> - The warning was absent with this patch in 3/3 equivalent runs.
>> - Ran the HID selftests against both baseline and patched kernels:
>> hid_bpf: 45 passed, 1 skipped, 0 failed
>> hidraw: 27 passed, 0 failed
>> hid-core, hid-apple, hid-gamepad, hid-ite, hid-keyboard, hid-mouse,
>> hid-multitouch, hid-sony, and hid-tablet all passed in both runs.
>> - hid-usb_crash.sh and hid-wacom.sh produced TAP 1..0 / rc=2 in both
>> kernels because no executable test cases were collected in this minimal
>> QEMU environment.
>> - No KASAN report, use-after-free, Oops, BUG, panic, or general protection
>> fault was observed.
>> - checkpatch.pl --strict --no-signoff reports 0 errors and 0 warnings.
>>
>> Reported-by: syzbot+c7c429f6851638ece81338f90c5b29ac9c0dea1f@syzkaller.appspotmail.com
>> Closes: https://syzkaller.appspot.com/bug?id=c7c429f6851638ece81338f90c5b29ac9c0dea1f
>> Signed-off-by: Zheng Shuhao <viennaoffh@gmail.com>
>> Tested-by: Zheng Shuhao <viennaoffh@gmail.com>
> You cannot add a Tested-by tag with your name. This is reserved for when
> someone independent of you tests your patch. Looking at the syzbot report
> there is a reproducer, so syzbot should test it. You can make syzbot test
> a patch by sending the following (note, this will trigger a test):
Ah, did some digging and the syzbot email is incorrect, it should be:
syzbot+fb951970a334aaff00ba@syzkaller.appspotmail.com
Cc'd the right syzbot and triggering the test.
#syz test
--
Kind regards,
Joshua Crofts
next prev parent reply other threads:[~2026-11-20 11:09 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-20 7:56 Zheng Shuhao
2026-11-20 10:50 ` Joshua Crofts
2026-11-20 10:50 ` syzbot
2026-11-20 11:09 ` Joshua Crofts [this message]
2026-11-20 11:09 ` syzbot
2026-11-20 12:14 ` Srinivas Pandruvada
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4f254948-29d5-4011-8865-c60a699d9bac@kernel.org \
--to=crofts@kernel.org \
--cc=bentiss@kernel.org \
--cc=jic23@kernel.org \
--cc=jikos@kernel.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-input@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=srinivas.pandruvada@linux.intel.com \
--cc=syzbot+fb951970a334aaff00ba@syzkaller.appspotmail.com \
--cc=viennaoffh@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®