From: system_lists@nullzone.org
To: linux-kernel@vger.kernel.org
Subject: Highpoint HPT370 not working in 2.4.18+ versions
Date: Thu, 26 Dec 2002 01:36:28 +0100 [thread overview]
Message-ID: <5.1.1.6.2.20021226012834.037b9558@192.168.2.131> (raw)
Hi there,
i have a Highpoint 370 which doesnt work in new kernel releases.
I'm just using 2.4.18 becouse other version upper doesnt detect the
Raid HW card.
Actualy i get this message with 2.4.18 (getting the most important about
this one):
--------
VP_IDE: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:pio, hdd:pio
HPT370A: IDE controller on PCI bus 00 dev 50
PCI: Found IRQ 11 for device 00:0a.0
HPT370A: chipset revision 4
HPT370A: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xc000-0xc007, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xc008-0xc00f, BIOS settings: hdg:pio, hdh:pio
hda: FUJITSU MPA3026ATU, ATA DISK drive
hde: ST380020A, ATA DISK drive
hdf: ST360020A, ATA DISK drive
hdg: ST380020A, ATA DISK drive
hdh: ST360020A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xb000-0xb007,0xb402 on irq 11
ide3 at 0xb800-0xb807,0xbc02 on irq 11
hda: 5126964 sectors (2625 MB), CHS=635/128/63
hde: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(33)
hdf: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33)
hdg: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=155061/16/63, UDMA(33)
hdh: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33)
Partition check:
hda: hda1 hda2 hda3 hda4
hde: unknown partition table
hdf: unknown partition table
hdg: [PTBL] [9729/255/63] hdg1
hdh: unknown partition table
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 96M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
ataraid/d0: ataraid/d0p1
Highpoint HPT370 Softwareraid driver for linux version 0.01
Drive 0 is 76319 Mb
Drive 1 is 57241 Mb
Raid array consists of 2 drives.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
--------
With new version o get only the:
...
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 96M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
Highpoint HPT370 Softwareraid driver for linux version ...
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
...
and its all....
May any tell me what is going bad with my card? is just a problem of drivers?
Seeya
Note: add to this .. if i set the IDE driver over UDMA33 i get DME timeout
and the system halt. Seeting UDMA to 33 the systems works withput problems
or needing any intervention for months.
next reply other threads:[~2002-12-26 0:27 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-12-26 0:36 system_lists [this message]
2002-12-28 0:12 ` Scott McDermott
2002-12-30 9:10 ` system_lists
2002-12-30 13:10 ` Alan Cox
2002-12-30 23:54 ` system_lists
2002-12-31 0:43 system_lists
2003-01-01 23:09 Kari Hameenaho
2003-01-02 21:51 ` system_lists
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5.1.1.6.2.20021226012834.037b9558@192.168.2.131 \
--to=system_lists@nullzone.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®