From: Mike Galbraith <efault@gmx.de>
To: linux-kernel@vger.kernel.org
Cc: Andrew Morton <akpm@osdl.org>
Subject: 2.6.0-test2+ext3+dbench=Buffer I/O error
Date: Wed, 30 Jul 2003 16:54:46 +0200 [thread overview]
Message-ID: <5.2.1.1.2.20030730163933.00b41b50@wen-online.de> (raw)
[-- Attachment #1: Type: text/plain, Size: 493 bytes --]
Greetings,
While trying to duplicate Randy Hron's "dbench has intermittent hang on
2.6.0-test1-ac2" report, I received quite a few "Buffer I/O error on
/dev/hda8, logical block N" messages. (changing elevators makes no
difference fwiw). I went back to test1, and it spat up a couple of "buffer
layer error" messages and associated traces. Attempting to umount
afterward to run fsck left umount in D state. See attachment.
Rebooting and running fsck turned up nothing wrong.
-Mike
[-- Attachment #2: xx --]
[-- Type: application/octet-stream, Size: 6105 bytes --]
...
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c596b (rev 11) IDE UDMA66 controller on pci0000:00:07.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
hda: IBM-DJNA-352030, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: MATSHITADVD-ROM SR-8583A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: host protected area => 1
hda: 39876480 sectors (20417 MB) w/1966KiB Cache, CHS=39560/16/63
hda: hda1 hda2 hda3 < hda5 hda6 hda7 hda8 >
end_request: I/O error, dev hdc, sector 0
hdc: ATAPI 32X DVD-ROM drive, 512kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
mice: PS/2 mouse device common for all mice
input: PS/2 Generic Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
i2c /dev entries driver module version 2.7.0 (20021208)
Advanced Linux Sound Architecture Driver Version 0.9.4 (Mon Jun 09 12:01:18 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
PCI: Found IRQ 9 for device 0000:00:0c.0
PCI: Sharing IRQ 9 with 0000:00:0f.0
ALSA device list:
#0: Yamaha DS-XG PCI (YMF740C) at 0xec000000, irq 9
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 112k freed
Adding 265064k swap on /dev/hda2. Priority:2 extents:1
blk: queue c048ddbc, I/O limit 4095Mb (mask 0xffffffff)
EXT3 FS on hda6, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SysRq : Changing Loglevel
Loglevel set to 9
buffer layer error at fs/buffer.c:1796
Call Trace:
[<c01415e9>] __buffer_error+0x29/0x30
[<c0142c13>] __block_write_full_page+0x1af/0x318
[<c0144131>] block_write_full_page+0xa1/0xac
[<c0146284>] blkdev_get_block+0x0/0x54
[<c01463ac>] blkdev_writepage+0x14/0x18
[<c0146284>] blkdev_get_block+0x0/0x54
[<c015abb9>] mpage_writepages+0x175/0x24c
[<c0146398>] blkdev_writepage+0x0/0x18
[<c01470c5>] generic_writepages+0x11/0x15
[<c012f204>] do_writepages+0x18/0x2c
[<c0159653>] __sync_single_inode+0x9f/0x1d0
[<c01597f0>] __writeback_single_inode+0x6c/0x74
[<c01599a1>] sync_sb_inodes+0x1a9/0x220
[<c0159a4d>] writeback_inodes+0x35/0x4c
[<c012ee0c>] balance_dirty_pages+0x64/0x12c
[<c012ef0b>] balance_dirty_pages_ratelimited+0x37/0x40
[<c012cc8c>] generic_file_aio_write_nolock+0x858/0x940
[<c01f9ac4>] __ide_dma_read+0x98/0xa0
[<c01f9228>] ide_dma_intr+0x0/0xac
[<c01f9780>] dma_timer_expiry+0x0/0xb0
[<c012ce66>] generic_file_aio_write+0x66/0x7c
[<c016ce1f>] ext3_file_write+0x2b/0xbc
[<c01407bd>] do_sync_write+0x81/0xb0
[<c014818d>] sys_fstat64+0x25/0x30
[<c014088c>] vfs_write+0xa0/0xd0
[<c01409f0>] sys_pwrite64+0x40/0x5c
[<c01089d3>] syscall_call+0x7/0xb
buffer layer error at fs/buffer.c:2642
Call Trace:
[<c01415e9>] __buffer_error+0x29/0x30
[<c014423f>] submit_bh+0x87/0x178
[<c012af76>] unlock_page+0xa/0x3c
[<c0142c78>] __block_write_full_page+0x214/0x318
[<c0144131>] block_write_full_page+0xa1/0xac
[<c0146284>] blkdev_get_block+0x0/0x54
[<c01463ac>] blkdev_writepage+0x14/0x18
[<c0146284>] blkdev_get_block+0x0/0x54
[<c015abb9>] mpage_writepages+0x175/0x24c
[<c0146398>] blkdev_writepage+0x0/0x18
[<c01470c5>] generic_writepages+0x11/0x15
[<c012f204>] do_writepages+0x18/0x2c
[<c0159653>] __sync_single_inode+0x9f/0x1d0
[<c01597f0>] __writeback_single_inode+0x6c/0x74
[<c01599a1>] sync_sb_inodes+0x1a9/0x220
[<c0159a4d>] writeback_inodes+0x35/0x4c
[<c012ee0c>] balance_dirty_pages+0x64/0x12c
[<c012ef0b>] balance_dirty_pages_ratelimited+0x37/0x40
[<c012cc8c>] generic_file_aio_write_nolock+0x858/0x940
[<c01f9ac4>] __ide_dma_read+0x98/0xa0
[<c01f9228>] ide_dma_intr+0x0/0xac
[<c01f9780>] dma_timer_expiry+0x0/0xb0
[<c012ce66>] generic_file_aio_write+0x66/0x7c
[<c016ce1f>] ext3_file_write+0x2b/0xbc
[<c01407bd>] do_sync_write+0x81/0xb0
[<c014818d>] sys_fstat64+0x25/0x30
[<c014088c>] vfs_write+0xa0/0xd0
[<c01409f0>] sys_pwrite64+0x40/0x5c
[<c01089d3>] syscall_call+0x7/0xb
umount D C4355E38 30185872 495 304 (NOTLB)
c4355e00 00000082 c11346b0 c4355e38 c4355e4c c2a51c80 00000001 c7ec2200
c01594f9 c1297770 c1297770 c11346b0 c4355e38 c4355e4c c268a080 c4355e08
c011643e 0000000d c012af55 c11346b0 c7ef8154 c4355ed4 00000000 c1140480
Call Trace:
[<c01594f9>] __mark_inode_dirty+0x29/0xa8
[<c011643e>] io_schedule+0xe/0x18
[<c012af55>] wait_on_page_bit+0x9d/0xb4
[<c0116a34>] autoremove_wake_function+0x0/0x38
[<c0116a34>] autoremove_wake_function+0x0/0x38
[<c015ab89>] mpage_writepages+0x145/0x24c
[<c0146398>] blkdev_writepage+0x0/0x18
[<c01470c5>] generic_writepages+0x11/0x15
[<c012f204>] do_writepages+0x18/0x2c
[<c012ac7b>] __filemap_fdatawrite+0x7f/0x8c
[<c012ac94>] filemap_fdatawrite+0xc/0x10
[<c014180b>] sync_blockdev+0x1b/0x3c
[<c0141894>] fsync_super+0x68/0x84
[<c014557d>] generic_shutdown_super+0x3d/0xf4
[<c0145d96>] kill_block_super+0x12/0x2c
[<c01454af>] deactivate_super+0x33/0x58
[<c01561b2>] __mntput+0x1e/0x24
[<c014acd3>] path_release+0x27/0x2c
[<c0156709>] sys_umount+0x71/0x7c
[<c013774f>] sys_munmap+0x37/0x54
[<c0156720>] sys_oldumount+0xc/0x10
[<c01089d3>] syscall_call+0x7/0xb
next reply other threads:[~2003-07-30 14:50 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-07-30 14:54 Mike Galbraith [this message]
2003-07-30 22:09 ` Andrew Morton
2003-07-30 22:55 ` Lou Langholtz
2003-07-31 12:05 ` Jens Axboe
2003-07-31 4:13 ` Mike Galbraith
2003-07-31 16:54 ` Bill Davidsen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5.2.1.1.2.20030730163933.00b41b50@wen-online.de \
--to=efault@gmx.de \
--cc=akpm@osdl.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®