From: Roger Quadros <rogerq@kernel.org>
To: "Théo Lebrun" <theo.lebrun@bootlin.com>,
"Greg Kroah-Hartman" <gregkh@linuxfoundation.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Krzysztof Kozlowski" <krzysztof.kozlowski+dt@linaro.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Peter Chen" <peter.chen@kernel.org>,
"Pawel Laszczak" <pawell@cadence.com>,
"Nishanth Menon" <nm@ti.com>,
"Vignesh Raghavendra" <vigneshr@ti.com>,
"Tero Kristo" <kristo@kernel.org>
Cc: linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 3/6] usb: cdns3-ti: add suspend/resume procedures for J7200
Date: Wed, 15 Nov 2023 13:37:51 +0200 [thread overview]
Message-ID: <5080372b-1f48-4cbc-a6c4-8689c28983cb@kernel.org> (raw)
In-Reply-To: <20231113-j7200-usb-suspend-v1-3-ad1ee714835c@bootlin.com>
On 13/11/2023 16:26, Théo Lebrun wrote:
> Hardware initialisation is only done at probe. The J7200 USB controller
> is reset at resume because of power-domains toggling off & on. We
> therefore (1) toggle PM runtime at suspend/resume & (2) reconfigure the
> hardware at resume.
at probe we are doing a pm_runtime_get() and never doing a put thus
preventing any runtime PM.
>
> Reuse the newly extracted cdns_ti_init_hw() function that contains the
> register write sequence.
>
> We guard this behavior based on compatible to avoid modifying the
> current behavior on other platforms. If the controller does not reset
> we do not want to touch PM runtime & do not want to redo reg writes.
>
> Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
> ---
> drivers/usb/cdns3/cdns3-ti.c | 48 +++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 47 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/cdns3/cdns3-ti.c b/drivers/usb/cdns3/cdns3-ti.c
> index c331bcd2faeb..50b38c4b9c87 100644
> --- a/drivers/usb/cdns3/cdns3-ti.c
> +++ b/drivers/usb/cdns3/cdns3-ti.c
> @@ -197,6 +197,50 @@ static int cdns_ti_probe(struct platform_device *pdev)
> return error;
> }
>
> +#ifdef CONFIG_PM
> +
> +static int cdns_ti_suspend(struct device *dev)
> +{
> + struct cdns_ti *data = dev_get_drvdata(dev);
> +
> + if (!of_device_is_compatible(dev_of_node(dev), "ti,j7200-usb"))
> + return 0;
> +
> + pm_runtime_put_sync(data->dev);
> +
> + return 0;
You might want to check suspend/resume ops in cdns3-plat and
do something similar here.
> +}
> +
> +static int cdns_ti_resume(struct device *dev)
> +{
> + struct cdns_ti *data = dev_get_drvdata(dev);
> + int ret;
> +
> + if (!of_device_is_compatible(dev_of_node(dev), "ti,j7200-usb"))
> + return 0;
> +
> + ret = pm_runtime_get_sync(dev);
> + if (ret < 0) {
> + dev_err(dev, "pm_runtime_get_sync failed: %d\n", ret);
> + goto err;
> + }
> +
> + cdns_ti_init_hw(data);
> +
> + return 0;
> +
> +err:
> + pm_runtime_put_sync(data->dev);
> + pm_runtime_disable(data->dev);
> + return ret;
> +}
> +
> +static const struct dev_pm_ops cdns_ti_pm_ops = {
> + SET_SYSTEM_SLEEP_PM_OPS(cdns_ti_suspend, cdns_ti_resume)
> +};
> +
> +#endif /* CONFIG_PM */
> +
> static int cdns_ti_remove_core(struct device *dev, void *c)
> {
> struct platform_device *pdev = to_platform_device(dev);
> @@ -218,6 +262,7 @@ static void cdns_ti_remove(struct platform_device *pdev)
> }
>
> static const struct of_device_id cdns_ti_of_match[] = {
> + { .compatible = "ti,j7200-usb", },
> { .compatible = "ti,j721e-usb", },
> { .compatible = "ti,am64-usb", },
> {},
> @@ -228,8 +273,9 @@ static struct platform_driver cdns_ti_driver = {
> .probe = cdns_ti_probe,
> .remove_new = cdns_ti_remove,
> .driver = {
> - .name = "cdns3-ti",
> + .name = "cdns3-ti",
> .of_match_table = cdns_ti_of_match,
> + .pm = pm_ptr(&cdns_ti_pm_ops),
> },
> };
>
>
--
cheers,
-roger
next prev parent reply other threads:[~2023-11-15 11:38 UTC|newest]
Thread overview: 35+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-13 14:26 [PATCH 0/6] usb: cdns: fix suspend on J7200 by assuming reset on resume Théo Lebrun
2023-11-13 14:26 ` [PATCH 1/6] dt-bindings: usb: ti,j721e-usb: add ti,j7200-usb compatible Théo Lebrun
2023-11-13 19:58 ` Conor Dooley
2023-11-13 14:26 ` [PATCH 2/6] usb: cdns3-ti: move reg writes from probe into an init_hw helper Théo Lebrun
2023-11-15 11:33 ` Roger Quadros
2023-11-15 14:23 ` Théo Lebrun
2023-11-16 12:00 ` Roger Quadros
2023-11-13 14:26 ` [PATCH 3/6] usb: cdns3-ti: add suspend/resume procedures for J7200 Théo Lebrun
2023-11-13 15:39 ` Gregory CLEMENT
2023-11-14 11:13 ` Théo Lebrun
2023-11-15 11:37 ` Roger Quadros [this message]
2023-11-15 15:02 ` Théo Lebrun
2023-11-16 12:40 ` Roger Quadros
2023-11-16 18:56 ` Théo Lebrun
2023-11-16 21:44 ` Roger Quadros
2023-11-17 10:17 ` Théo Lebrun
2023-11-17 11:51 ` Roger Quadros
2023-11-17 14:20 ` Théo Lebrun
2023-11-18 10:41 ` Roger Quadros
2023-11-22 22:23 ` Kevin Hilman
2023-11-23 9:51 ` Théo Lebrun
2023-11-26 22:36 ` Kevin Hilman
2023-11-27 13:25 ` Théo Lebrun
2023-12-12 18:26 ` Kevin Hilman
2023-12-12 19:31 ` Alan Stern
2023-11-13 14:26 ` [PATCH 4/6] usb: cdns3: support power-off of controller when in host role Théo Lebrun
2023-11-14 8:38 ` Peter Chen
2023-11-14 11:10 ` Théo Lebrun
2023-11-17 3:38 ` Peter Chen
2023-11-17 9:58 ` Théo Lebrun
2023-11-20 5:44 ` Peter Chen
2023-11-13 14:27 ` [PATCH 5/6] usb: cdns3-ti: notify cdns core that hardware resets across suspend on J7200 Théo Lebrun
2023-11-13 14:27 ` [PATCH 6/6] arm64: dts: ti: k3-j7200: use J7200-specific USB compatible Théo Lebrun
2023-11-14 10:01 ` Gregory CLEMENT
2023-11-14 11:14 ` Théo Lebrun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5080372b-1f48-4cbc-a6c4-8689c28983cb@kernel.org \
--to=rogerq@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=nm@ti.com \
--cc=pawell@cadence.com \
--cc=peter.chen@kernel.org \
--cc=robh+dt@kernel.org \
--cc=theo.lebrun@bootlin.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®