Re: [PATCH v2 0/4] devfreq: check the get_cur_freq() return value and use it in ufshcd

[Bean Huo <beanhuo@iokpp.de>]

Chanwoo, MyungJoo Ham, Kyungmin Park, who else maintains this, 

Patches 3/4 and 4/4 of this series have been picked up by the SCSI tree.

Patches 1/4 and 2/4 are the devfreq ones and do not depend on them.

Would you like to take them, or should I resend the two on their own against
your devfreq-next branch?

Kind regards,
Bean


On Mon, 2026-09-14 at 15:12 +0200, Bean Huo wrote:
> Hi Chanwoo,
> 
> A quick check. the patch 1/4, and patch 2/4 in this series would be queueing
> up
> for your pull requst?
> 
> Regards,
> Bean
> 
> 
> On Mon, 2026-09-07 at 21:21 +0200, Bean Huo wrote:
> > The devfreq core has three users of the optional ->get_cur_freq()
> > callback. Two of them check the return value, the third one does not and
> > passes an uninitialized frequency to the transition notifiers when the
> > callback fails. Patch 1 fixes that.
> > 
> > Patch 2 writes down what a driver is expected to return from the
> > callback. Today this has to be found by reading the devfreq core.
> > 
> > Patch 3 records the frequency the controller starts at.
> > ufshcd_init_clocks() puts the controller at its highest frequency, but
> > nothing writes that down, so clk_scaling.target_freq stays 0 and devfreq
> > starts with previous_freq at 0 as well. With use_pm_opp this makes
> > ufshcd_devfreq_get_dev_status() report 0 Hz, the ondemand governor then
> > asks for the maximum frequency, and ufshcd_devfreq_target() runs a full
> > ufshcd_devfreq_scale() that holds up the queue for up to a second only to
> > set the same OPP and the same gear again.
> > 
> > Patch 4 adds the ->get_cur_freq() callback to ufshcd. Without it the
> > cur_freq attribute shows the last frequency the governor selected, which
> > is wrong whenever the controller is scaled outside the governor, for
> > example after writing 0 to clkscale_enable.
> > 
> > The patches touch two subsystems. Patches 1 and 2 are for the devfreq
> > tree, patches 3 and 4 are for the SCSI tree. The two halves are
> > independent, at build time and at run time, and can be applied in either
> > order.
> > 
> > Patch was tested on a Radxa Dragon Q6A (1d84000.ufshc):
> > 
> >   before "echo 0 > clkscale_enable":  cur_freq 75000000, target_freq
> > 75000000
> >   after  "echo 0 > clkscale_enable":  cur_freq 300000000, target_freq
> > 75000000
> > 
> > Without it both files report 75000000 and keep doing so for as long as
> > clock scaling stays disabled. A 4 GiB direct read after enabling clock
> > scaling again counted the transitions in trans_stat and attributed time
> > to the 300000000 state, so the frequency the callback returns is one that
> > devfreq recognises.
> > 
> > One thing to be aware of: devfreq_monitor_resume() copies previous_freq
> > from the callback, but it does not call devfreq_update_status(). A
> > frequency change made while the governor was suspended therefore does not
> > show up as a transition. That is how devfreq behaves today and this
> > series does not change it.
> > 
> > Changes since v1:
> > - New patch 3, so that target_freq and devfreq's previous_freq are not 0
> >   at boot (suggested by Stanley Jhu).
> > - Patch 4: drop the !cur_freq check, it cannot happen any more.
> > - Drop the now stale comment in ufshcd_devfreq_get_dev_status().
> > - Patches 1 and 2 are unchanged.
> > - The devfreq and the ufshcd patches no longer depend on each other.
> > - Avri's Reviewed-by is on patches 1, 2 and 4. Patch 3 is new, so it does
> >   not carry it. Avri, please note that patch 4 changed since you reviewed
> >   it, the !cur_freq check is gone. Tell me if you want the tag dropped.
> > 
> > 
> > Bean Huo (4):
> >   PM / devfreq: Fall back to previous_freq when get_cur_freq() fails
> >   PM / devfreq: Add more details to the get_cur_freq() comment
> >   scsi: ufs: core: Record the frequency the controller starts at
> >   scsi: ufs: core: Report the current clock frequency to devfreq
> > 
> >  drivers/devfreq/devfreq.c |  5 ++---
> >  drivers/ufs/core/ufshcd.c | 37 +++++++++++++++++++++++++++++++------
> >  include/linux/devfreq.h   |  7 +++++--
> >  3 files changed, 38 insertions(+), 11 deletions(-)
> > 
> > 
> > base-commit: e30626823a406725ce29bc75cb8ec467d3e1e326
>