147c147,148
< Kernel command line: root=/dev/sda2
---
> Kernel command line: root=/dev/sda2 acpi_osi="!Windows 2006"
> ACPI: Deleted _OSI(Windows 2006)
174,175c175,176
< Detected 2094.823 MHz processor.
< Calibrating delay loop (skipped), value calculated using timer frequency.. 4191.21 BogoMIPS (lpj=6982743)
---
> Detected 2094.484 MHz processor.
> Calibrating delay loop (skipped), value calculated using timer frequency.. 4190.50 BogoMIPS (lpj=6981613)
199c200
< Calibrating delay using timer specific routine.. 4191.04 BogoMIPS (lpj=6982470)
---
> Calibrating delay using timer specific routine.. 4101.19 BogoMIPS (lpj=6832307)
208c209
< Total of 2 processors activated (8382.25 BogoMIPS).
---
> Total of 2 processors activated (8291.70 BogoMIPS).
389c390
< type=2000 audit(1263063441.759:1): initialized
---
> type=2000 audit(1263063607.762:1): initialized
455a457,466
> pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
> pata_acpi 0000:00:1f.1: setting latency timer to 64
> pata_acpi 0000:00:1f.1: PCI INT A disabled
> ata_piix 0000:00:1f.1: version 2.13
> ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
> ata_piix 0000:00:1f.1: setting latency timer to 64
> scsi0 : ata_piix
> scsi1 : ata_piix
> ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
> ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
462,463d472
< scsi0 : ahci
< scsi1 : ahci
465,468c474,482
< ata1: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 28
< ata2: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 28
< ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 28
< ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
---
> scsi3 : ahci
> ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WW01, max UDMA/33
> scsi4 : ahci
> ata3: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404100 irq 28
> ata4: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404180 irq 28
> ata5: SATA max UDMA/133 abar m2048@0xfc404000 port 0xfc404200 irq 28
> ata1.00: configured for UDMA/33
> scsi 0:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WW01 PQ: 0 ANSI: 5
> ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
470,491c484,495
< ata1.00: _GTF unexpected object type 0x1
< ata2: SATA link down (SStatus 0 SControl 300)
< ata3: SATA link down (SStatus 0 SControl 300)
< ata1.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133
< ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
< ata1.00: _GTF unexpected object type 0x1
< ata1.00: configured for UDMA/133
< scsi 0:0:0:0: Direct-Access     ATA      WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5
< pata_acpi 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
< pata_acpi 0000:00:1f.1: setting latency timer to 64
< pata_acpi 0000:00:1f.1: PCI INT A disabled
< ata_piix 0000:00:1f.1: version 2.13
< ata_piix 0000:00:1f.1: PCI INT A -> GSI 19 (level, low) -> IRQ 19
< ata_piix 0000:00:1f.1: setting latency timer to 64
< scsi3 : ata_piix
< scsi4 : ata_piix
< ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
< ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
< sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
< sd 0:0:0:0: [sda] Write Protect is off
< sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
< sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
---
> ata3.00: _GTF unexpected object type 0x1
> ata4: SATA link down (SStatus 0 SControl 300)
> ata5: SATA link down (SStatus 0 SControl 300)
> ata3.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133
> ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
> ata3.00: _GTF unexpected object type 0x1
> ata3.00: configured for UDMA/133
> scsi 2:0:0:0: Direct-Access     ATA      WDC WD2500BEVS-2 01.0 PQ: 0 ANSI: 5
> sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
> sd 2:0:0:0: [sda] Write Protect is off
> sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
> sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
493,496c497
< sd 0:0:0:0: [sda] Attached SCSI disk
< ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WW01, max UDMA/33
< ata4.00: configured for UDMA/33
< scsi 3:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T20N  WW01 PQ: 0 ANSI: 5
---
> sd 2:0:0:0: [sda] Attached SCSI disk
499c500
< sr 3:0:0:0: Attached scsi CD-ROM sr0
---
> sr 0:0:0:0: Attached scsi CD-ROM sr0
510d510
< Switching to clocksource hpet
513a514
> Switching to clocksource hpet
514a516,526
> sr 0:0:0:0: Attached scsi generic sg0 type 5
> sd 2:0:0:0: Attached scsi generic sg1 type 0
> ACPI: AC Adapter [AC0] (on-line)
> thermal LNXTHERM:01: registered as thermal_zone0
> ACPI: Thermal Zone [THRM] (59 C)
> iTCO_vendor_support: vendor-support=0
> ACPI: Battery Slot [BAT0] (battery present)
> input: PC Speaker as /devices/platform/pcspkr/input/input7
> iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
> iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
> iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
518,521c530,537
< sd 0:0:0:0: Attached scsi generic sg0 type 0
< sr 3:0:0:0: Attached scsi generic sg1 type 5
< ACPI: AC Adapter [AC0] (on-line)
< ACPI: Battery Slot [BAT0] (battery present)
---
> i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
> ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f]
> ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
> r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
> r8169 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
> r8169 0000:06:00.0: setting latency timer to 64
> r8169 0000:06:00.0: irq 29 for MSI/MSI-X
> eth0: RTL8101e at 0xf9088000, 00:03:0d:7c:54:60, XID 14000000 IRQ 29
541d556
< uhci_hcd: USB Universal Host Controller Interface driver
545a561
> uhci_hcd: USB Universal Host Controller Interface driver
586,595d601
< thermal LNXTHERM:01: registered as thermal_zone0
< ACPI: Thermal Zone [THRM] (59 C)
< i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19
< ACPI: I/O resource 0000:00:1f.3 [0x1c20-0x1c3f] conflicts with ACPI region SMBI [0x1c20-0x1c2f]
< ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
< r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
< r8169 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
< r8169 0000:06:00.0: setting latency timer to 64
< r8169 0000:06:00.0: irq 29 for MSI/MSI-X
< eth0: RTL8101e at 0xf9070000, 00:03:0d:7c:54:60, XID 14000000 IRQ 29
598,602c604,608
< iTCO_vendor_support: vendor-support=0
< input: PC Speaker as /devices/platform/pcspkr/input/input7
< iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
< iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x1060)
< iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
---
> HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
> HDA Intel 0000:00:1b.0: setting latency timer to 64
> Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
> input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
> input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
611,615d616
< Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
< input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
< HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
< HDA Intel 0000:00:1b.0: setting latency timer to 64
< input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input9
629,640d629
< fuse init (API version 7.13)
< wlan0: deauthenticating from 00:04:0e:60:53:78 by local choice (reason=3)
< wlan0: direct probe to AP 00:04:0e:60:53:78 (try 1)
< wlan0: direct probe responded
< wlan0: authenticate with AP 00:04:0e:60:53:78 (try 1)
< wlan0: authenticated
< wlan0: associate with AP 00:04:0e:60:53:78 (try 1)
< wlan0: RX AssocResp from 00:04:0e:60:53:78 (capab=0x411 status=0 aid=1)
< wlan0: associated
< ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
< padlock: VIA PadLock not detected.
< wlan0: no IPv6 routers present
