Re: [PATCH/RFC v10 09/19] DT: Add documentation for the mfd Maxim max77693

[Jacek Anaszewski <j.anaszewski@samsung.com>]

On 01/20/2015 12:21 PM, Lee Jones wrote:
> On Fri, 09 Jan 2015, Jacek Anaszewski wrote:
>
>> This patch adds device tree binding documentation for
>> the flash cell of the Maxim max77693 multifunctional device.
>>
>> Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
>> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
>> Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
>> Cc: Lee Jones <lee.jones@linaro.org>
>> Cc: Chanwoo Choi <cw00.choi@samsung.com>
>> Cc: Bryan Wu <cooloney@gmail.com>
>> Cc: Richard Purdie <rpurdie@rpsys.net>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Pawel Moll <pawel.moll@arm.com>
>> Cc: Mark Rutland <mark.rutland@arm.com>
>> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
>> Cc: Kumar Gala <galak@codeaurora.org>
>> ---
>>   Documentation/devicetree/bindings/mfd/max77693.txt |   69 ++++++++++++++++++++
>>   1 file changed, 69 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
>> index 01e9f30..ef184f0 100644
>> --- a/Documentation/devicetree/bindings/mfd/max77693.txt
>> +++ b/Documentation/devicetree/bindings/mfd/max77693.txt
>> @@ -41,7 +41,52 @@ Optional properties:
>>   	 To get more informations, please refer to documentaion.
>>   	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
>>
>> +- led : the LED submodule device node
>> +
>> +There are two led outputs available - fled1 and fled2. Each of them can
>> +control a separate led or they can be connected together to double
>> +the maximum current for a single connected led. One led is represented
>> +by one child node.
>> +
>> +Required properties:
>> +- compatible : Must be "maxim,max77693-led".
>> +
>> +Optional properties:
>> +- maxim,trigger-type : Flash trigger type.
>> +	Possible trigger types:
>> +		MAX77693_LED_TRIG_TYPE_EDGE - Rising edge of the signal triggers
>> +			the flash,
>> +		MAX77693_LED_TRIG_TYPE_LEVEL - Strobe pulse length controls
>> +			duration of the flash.
>
> I think you should represent the proper values here instead of the
> defines.

I see both versions in the existing bindings and also a combination of
them, e.g.: MAX77693_LED_TRIG_TYPE_EDGE (0). I think that it is
reasonable to mention the macros, especially if they are to appear
in the DT binding example at the end of the documentation file.

>> +- maxim,boost-mode :
>> +	In boost mode the device can produce up to 1.2A of total current
>> +	on both outputs. The maximum current on each output is reduced
>> +	to 625mA then. If not enabled explicitly, boost setting defaults to
>> +	MAX77693_LED_BOOST_FIXED in case both current sources are used.
>> +	Possible values:
>> +		MAX77693_LED_BOOST_OFF - no boost,
>> +		MAX77693_LED_BOOST_ADAPTIVE - adaptive mode,
>> +		MAX77693_LED_BOOST_FIXED - fixed mode.
>
> Same here.

MAX77693_LED_BOOST_OFF (0) - no boost,
MAX77693_LED_BOOST_ADAPTIVE (1) - adaptive mode,
MAX77693_LED_BOOST_FIXED (2) - fixed mode.

?

>
>> +- maxim,boost-vout : Output voltage of the boost module in millivolts.
>
> -mvout?
> -microvout?

maxim,boost-mvout ?

>> +- maxim,vsys-min : Low input voltage level in millivolts. Flash is not fired
>> +	if chip estimates that system voltage could drop below this level due
>> +	to flash power consumption.
>
> mvsys?
> microvsys?

maxim,mvsys-min ?

-- 
Best Regards,
Jacek Anaszewski