From: Tero Kristo <t-kristo@ti.com>
To: Vignesh Raghavendra <vigneshr@ti.com>, Nishanth Menon <nm@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v2 1/3] arm64: dts: ti: k3-j721e: Add DT nodes for few peripherials
Date: Fri, 17 Jan 2020 14:56:55 +0200 [thread overview]
Message-ID: <5532c7dc-f8b0-497b-5a66-2bcf52b99195@ti.com> (raw)
In-Reply-To: <20191211170414.7026-1-vigneshr@ti.com>
On 11/12/2019 19:04, Vignesh Raghavendra wrote:
> Enable I2Cs, ADCs, OSPIs and UFS peripherals present on J721e.
>
> Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
> ---
> v2:
>
> Add GPIO expander IRQ lines
Queued up whole series towards 5.6, thanks!
-Tero
>
> .../dts/ti/k3-j721e-common-proc-board.dts | 150 ++++++++++++++++++
> arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 99 ++++++++++++
> .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 104 ++++++++++++
> arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi | 45 ++++++
> 4 files changed, 398 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> index 2a3cd6174504..7a5c3d4adadd 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> @@ -67,6 +67,46 @@ main_usbss1_pins_default: main_usbss1_pins_default {
> J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
> >;
> };
> +
> + main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
> + >;
> + };
> +
> + main_i2c0_pins_default: main-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
> + J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
> + >;
> + };
> +
> + main_i2c1_pins_default: main-i2c1-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
> + J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
> + >;
> + };
> +
> + main_i2c3_pins_default: main-i2c3-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
> + J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
> + >;
> + };
> +
> + main_i2c6_pins_default: main-i2c6-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
> + J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
> + >;
> + };
> +
> + main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
> + pinctrl-single,pins = <
> + J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
> + >;
> + };
> };
>
> &wkup_pmx0 {
> @@ -75,6 +115,19 @@ sw11_button_pins_default: sw11_button_pins_default {
> J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
> >;
> };
> +
> + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
> + J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
> + J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
> + J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
> + J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
> + J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
> + J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
> + J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
> + >;
> + };
> };
>
> &wkup_uart0 {
> @@ -279,3 +332,100 @@ &usb1 {
> dr_mode = "host";
> maximum-speed = "high-speed";
> };
> +
> +&ospi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
> +
> + flash@0{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <4>;
> + spi-max-frequency = <40000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <2>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&tscadc0 {
> + adc {
> + ti,adc-channels = <0 1 2 3 4 5 6 7>;
> + };
> +};
> +
> +&tscadc1 {
> + adc {
> + ti,adc-channels = <0 1 2 3 4 5 6 7>;
> + };
> +};
> +
> +&main_i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +
> + exp1: gpio@20 {
> + compatible = "ti,tca6416";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + exp2: gpio@22 {
> + compatible = "ti,tca6424";
> + reg = <0x22>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> +
> +&main_i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c1_pins_default>;
> + clock-frequency = <400000>;
> +
> + exp4: gpio@20 {
> + compatible = "ti,tca6408";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c1_exp4_pins_default>;
> + interrupt-parent = <&main_gpio1>;
> + interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&main_i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c3_pins_default>;
> + clock-frequency = <400000>;
> +
> + exp3: gpio@20 {
> + compatible = "ti,tca6408";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> +
> +&main_i2c6 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c6_pins_default>;
> + clock-frequency = <400000>;
> +
> + exp5: gpio@20 {
> + compatible = "ti,tca6408";
> + reg = <0x20>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 1e4c2b78d66d..4f14b9a645c5 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -596,4 +596,103 @@ usb1: usb@6400000 {
> dr_mode = "otg";
> };
> };
> +
> + main_i2c0: i2c@2000000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2000000 0x0 0x100>;
> + interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 187 0>;
> + power-domains = <&k3_pds 187 TI_SCI_PD_SHARED>;
> + };
> +
> + main_i2c1: i2c@2010000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2010000 0x0 0x100>;
> + interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 188 0>;
> + power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + main_i2c2: i2c@2020000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2020000 0x0 0x100>;
> + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 189 0>;
> + power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + main_i2c3: i2c@2030000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2030000 0x0 0x100>;
> + interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 190 0>;
> + power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + main_i2c4: i2c@2040000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2040000 0x0 0x100>;
> + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 191 0>;
> + power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + main_i2c5: i2c@2050000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2050000 0x0 0x100>;
> + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 192 0>;
> + power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + main_i2c6: i2c@2060000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x2060000 0x0 0x100>;
> + interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 193 0>;
> + power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + ufs_wrapper: ufs-wrapper@4e80000 {
> + compatible = "ti,j721e-ufs";
> + reg = <0x0 0x4e80000 0x0 0x100>;
> + power-domains = <&k3_pds 277 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 277 1>;
> + assigned-clocks = <&k3_clks 277 1>;
> + assigned-clock-parents = <&k3_clks 277 4>;
> + ranges;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + ufs@4e84000 {
> + compatible = "cdns,ufshc-m31-16nm", "jedec,ufs-2.0";
> + reg = <0x0 0x4e84000 0x0 0x10000>;
> + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
> + freq-table-hz = <250000000 250000000>, <19200000 19200000>, <19200000 19200000>;
> + clocks = <&k3_clks 277 0>, <&k3_clks 277 1>, <&k3_clks 277 1>;
> + clock-names = "core_clk", "phy_clk", "ref_clk";
> + dma-coherent;
> + };
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 555dc7b7aedc..7cf1490f3928 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -121,4 +121,108 @@ wkup_gpio1: gpio@42100000 {
> clocks = <&k3_clks 114 0>;
> clock-names = "gpio";
> };
> +
> + mcu_i2c0: i2c@40b00000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x40b00000 0x0 0x100>;
> + interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 194 0>;
> + power-domains = <&k3_pds 194 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + mcu_i2c1: i2c@40b10000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x40b10000 0x0 0x100>;
> + interrupts = <GIC_SPI 853 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 195 0>;
> + power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>;
> + };
> +
> + wkup_i2c0: i2c@42120000 {
> + compatible = "ti,j721e-i2c", "ti,omap4-i2c";
> + reg = <0x0 0x42120000 0x0 0x100>;
> + interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clock-names = "fck";
> + clocks = <&k3_clks 197 0>;
> + power-domains = <&k3_pds 197 TI_SCI_PD_SHARED>;
> + };
> +
> + fss: fss@47000000 {
> + compatible = "simple-bus";
> + reg = <0x0 0x47000000 0x0 0x100>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ospi0: spi@47040000 {
> + compatible = "ti,am654-ospi";
> + reg = <0x0 0x47040000 0x0 0x100>,
> + <0x5 0x00000000 0x1 0x0000000>;
> + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
> + cdns,fifo-depth = <256>;
> + cdns,fifo-width = <4>;
> + cdns,trigger-address = <0x0>;
> + clocks = <&k3_clks 103 0>;
> + assigned-clocks = <&k3_clks 103 0>;
> + assigned-clock-parents = <&k3_clks 103 2>;
> + assigned-clock-rates = <166666666>;
> + power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + ospi1: spi@47050000 {
> + compatible = "ti,am654-ospi";
> + reg = <0x0 0x47050000 0x0 0x100>,
> + <0x7 0x00000000 0x1 0x00000000>;
> + interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>;
> + cdns,fifo-depth = <256>;
> + cdns,fifo-width = <4>;
> + cdns,trigger-address = <0x0>;
> + clocks = <&k3_clks 104 0>;
> + power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +
> + tscadc0: tscadc@40200000 {
> + compatible = "ti,am3359-tscadc";
> + reg = <0x0 0x40200000 0x0 0x1000>;
> + interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 0 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 0 1>;
> + assigned-clocks = <&k3_clks 0 3>;
> + assigned-clock-rates = <60000000>;
> + clock-names = "adc_tsc_fck";
> +
> + adc {
> + #io-channel-cells = <1>;
> + compatible = "ti,am3359-adc";
> + };
> + };
> +
> + tscadc1: tscadc@40210000 {
> + compatible = "ti,am3359-tscadc";
> + reg = <0x0 0x40210000 0x0 0x1000>;
> + interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
> + power-domains = <&k3_pds 1 TI_SCI_PD_EXCLUSIVE>;
> + clocks = <&k3_clks 1 1>;
> + assigned-clocks = <&k3_clks 1 3>;
> + assigned-clock-rates = <60000000>;
> + clock-names = "adc_tsc_fck";
> +
> + adc {
> + #io-channel-cells = <1>;
> + compatible = "ti,am3359-adc";
> + };
> + };
> };
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> index 1884fc70148f..7680109ca60a 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> @@ -27,3 +27,48 @@ secure_ddr: optee@9e800000 {
> };
> };
> };
> +
> +&wkup_pmx0 {
> + wkup_i2c0_pins_default: wkup_i2c0_pins_default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
> + J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> + >;
> + };
> +
> + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
> + pinctrl-single,pins = <
> + J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
> + J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* MCU_OSPI0_DQS */
> + J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0) /* MCU_OSPI0_D0 */
> + J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0) /* MCU_OSPI0_D1 */
> + J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0) /* MCU_OSPI0_D2 */
> + J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0) /* MCU_OSPI0_D3 */
> + J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_OSPI0_D4 */
> + J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_OSPI0_D5 */
> + J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_OSPI0_D6 */
> + J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_OSPI0_D7 */
> + J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
> + >;
> + };
> +};
> +
> +&ospi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
> +
> + flash@0{
> + compatible = "jedec,spi-nor";
> + reg = <0x0>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <8>;
> + spi-max-frequency = <40000000>;
> + cdns,tshsl-ns = <60>;
> + cdns,tsd2d-ns = <60>;
> + cdns,tchsh-ns = <60>;
> + cdns,tslch-ns = <60>;
> + cdns,read-delay = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
>
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
prev parent reply other threads:[~2020-01-17 12:57 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-11 17:04 Vignesh Raghavendra
2019-12-11 17:04 ` [PATCH v2 2/3] arm64: dts: ti: k3-am65: Add OSPI DT node Vignesh Raghavendra
2019-12-11 17:04 ` [PATCH v2 3/3] arm64: dts: k3-am654-base-board: Add IRQ line for GPIO expander Vignesh Raghavendra
2020-01-17 12:56 ` Tero Kristo [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5532c7dc-f8b0-497b-5a66-2bcf52b99195@ti.com \
--to=t-kristo@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®