mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Laurence Oberman <loberman@redhat.com>
To: John Garry <john.garry@linux.dev>,
	"Martin K . Petersen" <mkp@kernel.org>,
		linux-scsi@vger.kernel.org
Cc: "James E . J . Bottomley" <James.Bottomley@HansenPartnership.com>,
	 Bart Van Assche <bvanassche@acm.org>,
	Martin Wilck <mwilck@suse.com>, Hannes Reinecke <hare@kernel.org>,
		linux-kernel@vger.kernel.org, stable@vger.kernel.org
Subject: Re: [PATCH] scsi: scsi_dh_alua: set handler_data before alua_initialize()
Date: Sun, 15 Nov 2026 14:37:54 -0500	[thread overview]
Message-ID: <57f9665fb8c3571cff55b2fafceec7437634fd5d.camel@redhat.com> (raw)
In-Reply-To: <37cb0b01-0c6a-4b3d-b3d8-c4e5a45977a8@linux.dev>

On Sun, 2026-11-15 at 18:04 +0000, John Garry wrote:
> On 11/9/26 20:11, Laurence Oberman wrote:
> > Since commit 50759b881e1d ("scsi: device_handler: alua: Call
> > scsi_device_put() from non-atomic context"), alua_rtpg_queue() only
> > queues an RTPG when sdev->handler_data points at an alua_dh_data
> > whose
> > port group matches:
> > 
> > 	struct alua_dh_data *h = sdev->handler_data;
> > 	...
> > 	if (h && rcu_dereference(h->pg) == pg) {
> 
> Do we still require this check (for h being non-NULL) after the
> change 
> in this patch? I assume that we flush any calls to this function
> prior 
> to unsetting sdev->handler_data.
> 
> > 
> > However alua_bus_attach() only assigns sdev->handler_data after
> > alua_initialize() returns, and alua_initialize() ->
> > alua_check_vpd()
> > is where the initial RTPG is queued. At that point handler_data is
> > still NULL, so the initial RTPG is silently dropped: no RTPG is
> > sent,
> > nothing is logged, and sdev->access_state keeps its zeroed default
> > of
> > active/optimized for every path.
> > 
> > With dm-multipath this goes unnoticed, as pg_init calls
> > scsi_dh_activate() once the map is loaded, which queues an RTPG
> > after
> > handler_data is set, and multipathd's alua prioritizer issues its
> > own
> > RTPG from userspace. Anything relying on sdev->access_state without
> > a
> > subsequent activate (sysfs access_state/preferred_path, native SCSI
> > multipath path selection) sees every path as active/optimized until
> > a
> > Unit Attention or rescan triggers an RTPG.
> > 
> > Seen on an HP P2000 G3 FC array (implicit ALUA, two port groups,
> > four
> > paths per LUN) with dm-multipath not in use: sg_rtpg reports port
> > group
> > 0 active/non-optimized and port group 1 active/optimized, but
> > /sys/class/scsi_device/H:C:T:L/device/access_state reads
> > active/optimized on all four paths after boot, and no
> > "alua: port group XX state ..." message is logged. Writing
> > "activate"
> > to dh_state sends the RTPG and corrects access_state.
> > 
> > Kernels without commit 50759b881e1d queue the attach-time RTPG
> > unconditionally and are not affected.
> > 
> > Fix by assigning sdev->handler_data before calling
> > alua_initialize(),
> > and clearing it again on failure. sdev->handler is only set once
> > scsi_dh_handler_attach() sees ->attach() succeed, so no handler
> > callback can observe the partially initialised alua_dh_data. On the
> > failure paths of alua_initialize(), h has not been added to a port
> > group and no RTPG has been queued, so freeing it is unchanged.
> > 
> > Fixes: 50759b881e1d ("scsi: device_handler: alua: Call
> > scsi_device_put() from non-atomic context")
> > Cc: stable@vger.kernel.org
> > Signed-off-by: Laurence Oberman <loberman@redhat.com>
> > ---
> > 
> > Notes:
> >      Tested on an HP P2000 G3 FC array (30 LUNs, 4 paths each):
> > with this
> >      patch the "alua: port group 00 state N ..." messages are
> > logged during
> >      boot and access_state shows two active/optimized and two
> >      active/non-optimized paths per LUN without any manual
> > activate.
> >      Without it, all paths read active/optimized until an RTPG is
> > triggered.
> >      
> >      I found this while testing John Garry's native SCSI multipath
> > series
> >      (v9) on an HP P2000 G3 FC array (30 LUNs, 4 paths each, dm-
> > multipath
> >      not in use). Native multipath uses sdev->access_state for path
> >      selection, and every path showed active/optimized, although
> > sg_rtpg
> >      and dm-multipath (alua prio 50/10) both report port group 0 as
> >      active/non-optimized. No "alua: port group XX state ..."
> > message was
> >      logged at boot. Writing "activate" to dh_state corrected
> > access_state,
> >      which pointed at the attach-time RTPG never being queued.
> >      
> >      With this patch, the port group state messages are logged
> > during boot
> >      and access_state shows two active/optimized and two
> >      active/non-optimized paths per LUN without any manual
> > activate.
> >      
> >      This fix is independent of the native multipath series. It
> > affects any
> >      user of access_state/preferred_path, and ALUA prep_fn fast-
> > fail, on
> >      kernels with 50759b881e1d where nothing calls
> > scsi_dh_activate()
> >      after attach.
> >      
> >      v9 series:
> > https://lore.kernel.org/linux-scsi/20261108204733.557995-1-
> >      john.garry@linux.dev/
> > 
> >   drivers/scsi/device_handler/scsi_dh_alua.c | 9 ++++++++-
> >   1 file changed, 8 insertions(+), 1 deletion(-)
> > 
> > diff --git a/drivers/scsi/device_handler/scsi_dh_alua.c
> > b/drivers/scsi/device_handler/scsi_dh_alua.c
> > index 87ac0a6d63e5..84ff3aed2c46 100644
> > --- a/drivers/scsi/device_handler/scsi_dh_alua.c
> > +++ b/drivers/scsi/device_handler/scsi_dh_alua.c
> > @@ -1233,13 +1233,20 @@ static int alua_bus_attach(struct
> > scsi_device *sdev)
> >   	INIT_LIST_HEAD(&h->node);
> >   
> >   	mutex_init(&h->init_mutex);
> > +	/*
> > +	 * alua_rtpg_queue() only queues an RTPG when sdev-
> > >handler_data
> > +	 * points at this alua_dh_data, so set it before
> > alua_initialize()
> > +	 * otherwise the initial RTPG issued from alua_check_vpd()
> > is
> > +	 * silently dropped and sdev->access_state is never
> > populated.
> > +	 */
> > +	sdev->handler_data = h;
> 
> Note: I was checking which members of alua_dh_data are not
> initialized 
> prior to publishing sdev->handler_data, and alua_dh_data.group_id is 
> never accessed at all AFAICS.
> 
> Thanks,
> John
On 11/15/26, John Garry wrote:
> Do we still require this check (for h being non-NULL) after the
change
> in this patch? I assume that we flush any calls to this function
prior
> to unsetting sdev->handler_data.

Hi John,

Thanks for looking at this.

You're right, with this patch the NULL check is redundant. All three
callers already have a valid h:

- alua_check_vpd() is called from attach/rescan with h passed in, and
  sdev->handler_data now points at it before the initial RTPG is
  queued
- alua_activate() and alua_check() both dereference
  sdev->handler_data (h->init_mutex, h->pg) before calling
  alua_rtpg_queue()

There is no explicit flush, but there doesn't need to be:
handler_data is only cleared in alua_bus_detach(), which runs from
scsi_dh_release_device() in scsi_device_dev_release(), i.e. after the
last sdev reference is dropped. Every caller holds a reference,
alua_rtpg_queue() takes its own scsi_device_get() before reading
handler_data, and queued RTPG work holds one through pg->rtpg_sdev.

The rcu_dereference(h->pg) == pg part is still needed, as a rescan can
move h to a different port group.

> Note: I was checking which members of alua_dh_data are not
initialized
> prior to publishing sdev->handler_data, and alua_dh_data.group_id is
> never accessed at all AFAICS.

Agreed, group_id is never read or written. All other members are
initialized before handler_data is set (h is kzalloc'd, and disabled
is set under init_mutex in alua_initialize()).

I would prefer to keep this patch minimal since it is tagged for
stable, and send a follow-up cleanup that drops the now-redundant
h check in alua_rtpg_queue() and removes the unused group_id member.
Does that work for you, or would you rather I fold both into a v2?

Thanks,
Laurence


      reply	other threads:[~2026-11-15 19:37 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-11-09 20:11 Laurence Oberman
2026-11-11 11:14 ` Martin Wilck
2026-11-15 18:04 ` John Garry
2026-11-15 19:37   ` Laurence Oberman [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=57f9665fb8c3571cff55b2fafceec7437634fd5d.camel@redhat.com \
    --to=loberman@redhat.com \
    --cc=James.Bottomley@HansenPartnership.com \
    --cc=bvanassche@acm.org \
    --cc=hare@kernel.org \
    --cc=john.garry@linux.dev \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-scsi@vger.kernel.org \
    --cc=mkp@kernel.org \
    --cc=mwilck@suse.com \
    --cc=stable@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®