mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Rafael J. Wysocki" <rafael@kernel.org>
To: Linux PM <linux-pm@vger.kernel.org>
Cc: LKML <linux-kernel@vger.kernel.org>,
	Christian Loehle <christian.loehle@arm.com>,
	Doug Smythies <dsmythies@telus.net>
Subject: [PATCH v1] cpuidle: governors: menu: Always check timers with tick stopped
Date: Tue, 20 Jan 2026 16:26:14 +0100	[thread overview]
Message-ID: <5959091.DvuYhMxLoT@rafael.j.wysocki> (raw)

From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

After commit 5484e31bbbff ("cpuidle: menu: Skip tick_nohz_get_sleep_length()
call in some cases"), if the return value of get_typical_interval()
multiplied by NSEC_PER_USEC is not greater than RESIDENCY_THRESHOLD_NS,
the menu governor will skip computing the time till the closest timer.
If that happens when the tick has been stopped already, the selected
idle state may be too deep due to the subsequent check comparing
predicted_ns with TICK_NSEC and causing its value to be replaced with
the expected time till the closest timer, which is KTIME_MAX in that
case.  That will cause the deepest enabled idle state to be selected,
but the time till the closest timer very well may be shorter than the
target residency of that state, in which case a shallower state should
be used.

Address this by making menu_select() always compute the time till the
closest timer when the tick has been stopped.

Also move the predicted_ns check mentioned above into the branch in
which the time till the closest timer is determined because it only
needs to be done in that case.

Fixes: 5484e31bbbff ("cpuidle: menu: Skip tick_nohz_get_sleep_length() call in some cases")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
---
 drivers/cpuidle/governors/menu.c |   22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

--- a/drivers/cpuidle/governors/menu.c
+++ b/drivers/cpuidle/governors/menu.c
@@ -239,7 +239,7 @@ static int menu_select(struct cpuidle_dr
 
 	/* Find the shortest expected idle interval. */
 	predicted_ns = get_typical_interval(data) * NSEC_PER_USEC;
-	if (predicted_ns > RESIDENCY_THRESHOLD_NS) {
+	if (predicted_ns > RESIDENCY_THRESHOLD_NS || tick_nohz_tick_stopped()) {
 		unsigned int timer_us;
 
 		/* Determine the time till the closest timer. */
@@ -259,6 +259,16 @@ static int menu_select(struct cpuidle_dr
 				   RESOLUTION * DECAY * NSEC_PER_USEC);
 		/* Use the lowest expected idle interval to pick the idle state. */
 		predicted_ns = min((u64)timer_us * NSEC_PER_USEC, predicted_ns);
+		/*
+		 * If the tick is already stopped, the cost of possible short
+		 * idle duration misprediction is much higher, because the CPU
+		 * may be stuck in a shallow idle state for a long time as a
+		 * result of it.  In that case, say we might mispredict and use
+		 * the known time till the closest timer event for the idle
+		 * state selection.
+		 */
+		if (tick_nohz_tick_stopped() && predicted_ns < TICK_NSEC)
+			predicted_ns = data->next_timer_ns;
 	} else {
 		/*
 		 * Because the next timer event is not going to be determined
@@ -285,16 +295,6 @@ static int menu_select(struct cpuidle_dr
 	}
 
 	/*
-	 * If the tick is already stopped, the cost of possible short idle
-	 * duration misprediction is much higher, because the CPU may be stuck
-	 * in a shallow idle state for a long time as a result of it.  In that
-	 * case, say we might mispredict and use the known time till the closest
-	 * timer event for the idle state selection.
-	 */
-	if (tick_nohz_tick_stopped() && predicted_ns < TICK_NSEC)
-		predicted_ns = data->next_timer_ns;
-
-	/*
 	 * Find the idle state with the lowest power while satisfying
 	 * our constraints.
 	 */




             reply	other threads:[~2026-01-20 15:26 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-01-20 15:26 Rafael J. Wysocki [this message]
2026-01-21 13:39 ` Christian Loehle
2026-01-28  5:19 ` Doug Smythies
2026-01-28 18:05   ` Rafael J. Wysocki

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=5959091.DvuYhMxLoT@rafael.j.wysocki \
    --to=rafael@kernel.org \
    --cc=christian.loehle@arm.com \
    --cc=dsmythies@telus.net \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®