From: Muhammad Abdul WAHAB <muhammadabdul.wahab@supelec.fr>
To: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Cc: Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Russell King <linux@armlinux.org.uk>,
Michal Simek <michal.simek@xilinx.com>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] Adding Support for Coresight Components on Zynq 7000.
Date: Mon, 3 Oct 2016 14:56:16 +0200 [thread overview]
Message-ID: <5b56a00a-ac69-b15d-1155-bab53ed766f3@supelec.fr> (raw)
In-Reply-To: <20160930165325.GA7630@xsjsorenbubuntu>
Hi Sören,
> I tried to refresh my Zynq knowledge a bit. The clkc provides the
> dbg_trc clock, and that is the clock you need (not fclk). I couldn't
> find it in the binding (I guess I messed that up), but apparently,
> you can provide a 'trace_emio_clk' as input to the clkc node in the
> Zynq DT. Then, with the muxes correctly configured (FSBL should do
> that if you select the EMIO trace clock in Vivado), the dbg_trc
> output of the clkc should be that EMIO clock. And the dbg_trc output
> of the clkc is what should be consumed by the tpiu node. Though, as
> I see it the binding/driver for the TPIU do not support that.
>
> I.e.
> In the clkc description you'd have to add 'trace_emio_clk' to the
> clock-names property together with a matching reference in the 'clocks'
> property. As this change would be specific to local setups, this is not
> really appropriate for upstream.
>
> Then, for the trace clock, ideally the TPIU would consume and enable it
> as needed.
Thank you very much for this. I will have a look into it.
Below is the patch without TPIU, is it possible to submit it ? I will
submit the TPIU part very soon once I manage to get it working.
> Unfortunately, this is not how it works. The DT bindings are not a
> recommendation. The DT description must follow the binding, otherwise
> drivers will not work correctly, or best case, just ignore what you put
> there.
Thanks. The idea of including TPIU part was to get feedback as I am far
from being an expert on DT.
> As I don't see this in the coresight binding, I doubt that it has any
> effect or should be here.
That's what I was thinking also. I will re-look into TPIU part and send
it soon. Besides, if I want to ask you a question regarding TPIU or DT,
can I contact you alone or should I keep sending it to all the CS/DT
maintainers ?
Thanks,
M.Abdul WAHAB
---
--- linux-4.7/arch/arm/boot/dts/zynq-7000.dtsi.orig 2016-07-24
21:23:50.000000000 +0200
+++ linux-4.7/arch/arm/boot/dts/zynq-7000.dtsi 2016-10-03
14:38:00.164515838 +0200
@@ -96,6 +96,57 @@
rx-fifo-depth = <0x40>;
};
+ etb@F8801000 {
+ compatible = "arm,coresight-etb10", "arm,primecell";
+ reg = <0xf8801000 0x1000>;
+
+ coresight-default-sink;
+ clocks = <&clkc 47>;
+ clock-names = "apb_pclk";
+
+ port {
+ etb_in_port: endpoint@0 {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port0>;
+ };
+ };
+ };
+
+ funnel@F8804000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0xf8804000 0x1000>;
+
+ clocks = <&clkc 47>;
+ clock-names = "apb_pclk";
+ ports {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ port@0 {
+ reg = <0x0>;
+ funnel_out_port0: endpoint {
+ remote-endpoint = <&replicator_in_port0>;
+ };
+ };
+
+ port@1 {
+ reg = <0x0>;
+ funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&ptm0_out_port>;
+ };
+ };
+
+ port@2 {
+ reg = <0x1>;
+ funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&ptm1_out_port>;
+ };
+ };
+ };
+ };
+
gpio0: gpio@e000a000 {
compatible = "xlnx,zynq-gpio-1.0";
#gpio-cells = <2>;
@@ -311,6 +362,67 @@
clocks = <&clkc 4>;
};
+ ptm0@F889C000 {
+ compatible = "arm,coresight-etm3x", "arm,primecell";
+ reg = <0xf889c000 0x1000>;
+
+ cpu = <&cpu0>;
+ clocks = <&clkc 47>;
+ clock-names = "apb_pclk";
+
+ port {
+ ptm0_out_port: endpoint {
+ remote-endpoint = <&funnel_in_port0>;
+ };
+ };
+ };
+
+ ptm1@F889D000 {
+ compatible = "arm,coresight-etm3x", "arm,primecell";
+ reg = <0xf889d000 0x1000>;
+
+ cpu = <&cpu1>;
+ clocks = <&clkc 47>;
+ clock-names = "apb_pclk";
+
+ port {
+ ptm1_out_port: endpoint {
+ remote-endpoint = <&funnel_in_port1>;
+ };
+ };
+ };
+
+ replicator {
+ compatible = "arm,coresight-replicator";
+
+ ports {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+
+ port@0 {
+ reg = <0x0>;
+ replicator_out_port0: endpoint {
+ remote-endpoint = <&etb_in_port>;
+ };
+ };
+
+ port@1 {
+ reg = <0x1>;
+ replicator_out_port1: endpoint {
+ remote-endpoint = <&tpiu_in_port>;
+ };
+ };
+
+ port@2 {
+ reg = <0x0>;
+ replicator_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&funnel_out_port0>;
+ };
+ };
+ };
+ };
+
ttc0: timer@f8001000 {
interrupt-parent = <&intc>;
interrupts = <0 10 4>,
next prev parent reply other threads:[~2016-10-03 12:56 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-09-29 10:26 Muhammad Abdul WAHAB
2016-09-29 14:34 ` Sören Brinkmann
2016-09-30 7:39 ` Muhammad Abdul WAHAB
2016-09-30 16:53 ` Sören Brinkmann
2016-10-03 12:56 ` Muhammad Abdul WAHAB [this message]
2016-10-03 13:30 ` Sören Brinkmann
2016-10-03 14:16 ` Muhammad Abdul WAHAB
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5b56a00a-ac69-b15d-1155-bab53ed766f3@supelec.fr \
--to=muhammadabdul.wahab@supelec.fr \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=michal.simek@xilinx.com \
--cc=robh+dt@kernel.org \
--cc=soren.brinkmann@xilinx.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®