From: "Tandra, Vasantha Likitha" <VasanthaLikitha.Tandra@amd.com>
To: linux-i2c@vger.kernel.org
Cc: michal.simek@amd.com, andi.shyti@kernel.org,
linux-kernel@vger.kernel.org, git@amd.com,
Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Subject: Re: [PATCH v2] i2c: xiic: Rework dynamic-mode RX FIFO drain in xiic_read_rx
Date: Mon, 16 Nov 2026 11:14:34 +0530 [thread overview]
Message-ID: <60062cf9-438e-4e03-8ebb-46cf0d327421@amd.com> (raw)
In-Reply-To: <20260928073425.2597782-1-vasanthalikitha.tandra@amd.com>
Hi Andi,
Could you please review the patch?
Thanks,
Vasantha Likitha
On 9/28/2026 1:04 PM, Vasantha Likitha T wrote:
> From: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
>
> Programming the RFD (RX FIFO depth) threshold at runtime causes a
> spurious SCL clock pulse which results in the STOP condition being
> missed.
>
> Fix this by programming RFD once, when the receive transfer starts, and
> handling the final-byte sequencing in software: select how many bytes to
> drain from the RX FIFO on each RX_FULL interrupt instead of
> reprogramming RFD after every read.
>
> RX_FULL is then always raised at the same threshold. When fewer bytes
> remain to be received after the current FIFO contents are accounted for,
> drain only that remaining count and retain the other bytes in the FIFO.
> The retained bytes together with the bytes still arriving restore the
> FIFO occupancy to the fixed threshold. Otherwise, drain the FIFO
> completely.
>
> Fixes: e1d5b6598cdc ("i2c: Add support for Xilinx XPS IIC Bus Interface")
> Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
> Co-developed-by: Vasantha Likitha T <vasanthalikitha.tandra@amd.com>
> Signed-off-by: Vasantha Likitha T <vasanthalikitha.tandra@amd.com>
> ---
> Changes in v2:
> - Updated commit message and Fixes tag
> - Removed dead code
> - Reused cached rx_space
> - Improved comment wording
> ---
> drivers/i2c/busses/i2c-xiic.c | 39 ++++++++++++++++++++++-------------
> 1 file changed, 25 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
> index 3e7735e1dae0..474540d4d611 100644
> --- a/drivers/i2c/busses/i2c-xiic.c
> +++ b/drivers/i2c/busses/i2c-xiic.c
> @@ -578,7 +578,8 @@ static void xiic_smbus_block_read_setup(struct xiic_i2c *i2c)
> static void xiic_read_rx(struct xiic_i2c *i2c)
> {
> u8 bytes_in_fifo, cr = 0, bytes_to_read = 0;
> - u32 bytes_rem = 0;
> + u32 bytes_rem;
> + u32 rx_space;
> int i;
>
> bytes_in_fifo = xiic_getreg8(i2c, XIIC_RFO_REG_OFFSET) + 1;
> @@ -590,13 +591,32 @@ static void xiic_read_rx(struct xiic_i2c *i2c)
> xiic_getreg8(i2c, XIIC_SR_REG_OFFSET),
> xiic_getreg8(i2c, XIIC_CR_REG_OFFSET));
>
> - if (bytes_in_fifo > xiic_rx_space(i2c))
> - bytes_in_fifo = xiic_rx_space(i2c);
> + rx_space = xiic_rx_space(i2c);
> +
> + /* Do not read more bytes than are still expected for this message */
> + if (bytes_in_fifo > rx_space)
> + bytes_in_fifo = rx_space;
>
> bytes_to_read = bytes_in_fifo;
>
> - if (!i2c->dynamic) {
> - bytes_rem = xiic_rx_space(i2c) - bytes_in_fifo;
> + if (i2c->dynamic) {
> + /*
> + * RFD is set by xiic_start_recv() and must not be changed during
> + * a transfer, because reprogramming it may generate a spurious
> + * SCL pulse and cause the STOP condition to be missed.
> + */
> + bytes_rem = rx_space - bytes_in_fifo;
> +
> + /*
> + * If fewer bytes remain to arrive than are currently in the FIFO,
> + * drain only that remaining count. The retained FIFO bytes together
> + * with the bytes still arriving restore the FIFO occupancy to the
> + * fixed threshold. Otherwise, drain the FIFO completely.
> + */
> + if (bytes_rem && bytes_rem < bytes_in_fifo)
> + bytes_to_read = bytes_rem;
> + } else {
> + bytes_rem = rx_space - bytes_in_fifo;
>
> /* Set msg length if smbus_block_read */
> if (i2c->rx_msg->flags & I2C_M_RECV_LEN) {
> @@ -636,15 +656,6 @@ static void xiic_read_rx(struct xiic_i2c *i2c)
> i2c->rx_msg->buf[i2c->rx_pos++] =
> xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
> }
> -
> - if (i2c->dynamic) {
> - u8 bytes;
> -
> - /* Receive remaining bytes if less than fifo depth */
> - bytes = min_t(u8, xiic_rx_space(i2c), IIC_RX_FIFO_DEPTH);
> - bytes--;
> - xiic_setreg8(i2c, XIIC_RFD_REG_OFFSET, bytes);
> - }
> }
>
> static bool xiic_error_check(struct xiic_i2c *i2c)
prev parent reply other threads:[~2026-11-16 5:47 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-28 7:34 Vasantha Likitha T
2026-11-16 5:44 ` Tandra, Vasantha Likitha [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=60062cf9-438e-4e03-8ebb-46cf0d327421@amd.com \
--to=vasanthalikitha.tandra@amd.com \
--cc=andi.shyti@kernel.org \
--cc=git@amd.com \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=michal.simek@amd.com \
--cc=shubhrajyoti.datta@amd.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®