From: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
To: "Ryan Brue" <ryanbrue.dev@gmail.com>,
"Jonathan Cameron" <jic23@kernel.org>,
"David Lechner" <dlechner@baylibre.com>,
"Nuno Sá" <nuno.sa@analog.com>,
"Andy Shevchenko" <andy@kernel.org>,
"Rob Herring" <robh@kernel.org>,
"Krzysztof Kozlowski" <krzk+dt@kernel.org>,
"Conor Dooley" <conor+dt@kernel.org>,
"Matthias Brugger" <matthias.bgg@gmail.com>
Cc: Roman Vivchar <rva333@protonmail.com>,
Luca Leonardo Scorcia <l.scorcia@gmail.com>,
linux-iio@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org,
Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>,
Andy Shevchenko <andriy.shevchenko@intel.com>
Subject: Re: [PATCH v5 0/2] iio: adc: add mt6397 PMIC AUXADC support
Date: Tue, 17 Nov 2026 12:02:47 +0100 [thread overview]
Message-ID: <60eeaaf9-57db-4ca7-b4f5-bdec111dcdbb@collabora.com> (raw)
In-Reply-To: <89c8cadb-0ccb-4aac-9b95-89f355beb24a@collabora.com>
On 11/17/26 11:56, AngeloGioacchino Del Regno wrote:
> On 10/25/26 06:18, Ryan Brue wrote:
>> The MediaTek mt6397 PMIC has a 10-bit AUXADC that nothing in-tree can
>> reach. On boards built around it that ADC is the only path to the battery:
>> the SoC's AUXADC is wired to board thermistors, and the charger ICs these
>> boards use have no ADC at all, so without it there is no pack voltage and
>> no state of charge.
>>
>
> I picked the Amazon Fire HD 10 series, confident that this series will also
> be picked for this cycle by the IIO maintainers, as this was fully reviewed.
>
> So please-please-please pick this one ASAP so that we don't get dt warnings.
>
I reiterate - I couldn't pick the series because, of course, that one depends
on the binding being merged, otherwise the header won't be there and the build
fails.
So I can't pick the DTS until the next cycle (granted that this series lands).
Cheers,
Angelo
> Cheers,
> Angelo
>
>> Patch 1 adds the compatible to the existing MediaTek PMIC AUXADC schema and
>> the header naming the channels, patch 2 the driver. The MFD cell that
>> instantiates it was patch 3 of v4, which Lee has applied [1].
>>
>> The mt6397 is not given mediatek,mt6359-auxadc as a fallback because the
>> two are not register compatible; patch 1 has the detail.
>>
>> Only the two channels a board needs for its pack are described, so patch 1
>> ships a header naming them: a channel ID is an index into the driver's
>> array and not the PMIC's channel number, as in mt6323-auxadc. The register
>> sequences are the ones the vendor kernel's pmic_auxadc.c programs.
>>
>> Tested on an Amazon Fire HD 10 (2017), an mt8173 with an mt6397. Both
>> channels are exercised: the battery channel by a fuel gauge, which reads
>> 817 counts, 3830 mV with the pack at rest, and the thermistor channel by an
>> ntc-thermistor consuming it. The error paths are driven by injecting a
>> regmap failure into each helper in turn. The read returns the injected
>> error, and every bit is cleared again. The teardown writes were also made
>> to fail, one at a time. When one write fails, the others still run, and
>> only the failed write's bits are left set. The next read clears them
>> anyway. Run the same way, v3 stopped at the first failed write and left the
>> later bits set. v5 gives the same results as v4 in all of these. Loading
>> the two modules alternately on the board, their readings differ by 0.3 LSB
>> on the battery channel and 0.1 LSB on the thermistor, both inside the
>> comparison's own noise.
>>
>> A new driver was created here, instead of modifying an existing driver such
>> as mt6323-auxadc or mt6359-auxadc, for the following reasons:
>>
>> - Both mt6323-auxadc and mt6359-auxadc select channels through a request
>> register (1 bit per channel), while mt6397 uses a 4-bit numeric field
>> CHSEL in CON1 (10:7), and then pulses a START bit (CON1 bit 0).
>>
>> - For mt6323-auxadc, which is the closest I could find to the mt6397
>> (CON0..CON27), it has 13 more registers than the mt6397 (CON0..CON14).
>> It uses CON22 for its request register, and reads the result value
>> from the same register as the ready bit. We don't do that - the mt6397
>> has a factory-calibrated value for each channel at 0x16 higher than the
>> raw value. mt6323 also has a 1800 mV / 15 bit scale / resolution while
>> we have 1200 mV / 10 bits. We also have some per-channel preparation
>> that we have to do before the burst, that the mt6323 doesn't have to
>> do.
>>
>> - For mt6359-auxadc, it has a more generic framework for describing the
>> AUXADC, but it assumes requests are channel-per-bit, and so we would
>> have to basically ignore req_idx, req_mask, rdy_idx, and rdy_mask.
>>
>> - We also have our own software sampling, which the vendor does too
>> (Amazon Fire OS based on Linux 3.18). We'd have to have our own
>> sampling callback to do it.
>>
>> I have two things in the driver different from the vendor (Amazon
>> Fire OS based on a 3.18 kernel). Verified with over 150 interleaved reads
>> per setting:
>>
>> - Leaving the ISENSE input enabled between reads, as the vendor does,
>> makes no difference to the value, so the driver switches it off again.
>> Both ADC input enables are clear when idle, unless a teardown write
>> itself fails: the rest of the teardown still runs, and the next read of
>> the channel clears whatever was left set.
>>
>> - The chip's sample accumulator makes no difference at 4, 8, 16 or 31
>> samples and costs no measurable time, so it is left at one. Software
>> averaging helps, but only by about a quarter: in one interleaved run,
>> 0.92 LSB standard deviation for one conversion against 0.67 for sixteen,
>> where independent samples would have given 0.23. Conversions in a burst
>> are correlated.
>>
>> The reading was checked against the charger, which regulates the pack to
>> a programmed voltage in constant-voltage mode. Over twelve such voltages
>> from 3904 to 4080 mV, and charge currents from 111 to 778 mA, the driver's
>> reading is a mean of 0.9 mV from the regulated value, well inside
>> the charger's regulation tolerance. That also settles reading the chip's
>> trimmed result register rather than the raw one - the raw register is
>> 20.7 mV low at every one of the twelve points.
>>
>> This series was developed with the help of an LLM coding assistant.
>>
>> [1] https://lore.kernel.org/all/179206667779.1910726.5341177428334836457.b4-ty@b4/
>>
>> Signed-off-by: Ryan Brue <ryanbrue.dev@gmail.com>
>> ---
>> Changes in v5:
>> - Split the read into one helper per channel, each doing its own setup,
>> burst and teardown, and a caller that takes the lock and dispatches on
>> the channel. mt6397_auxadc_release() is gone. The register sequence is
>> unchanged on every path, including every failure path, and retested on
>> hardware. (Jonathan)
>> - Keep Andy's Reviewed-by on patch 2, since the change is a restructure
>> that does not change behavior. If that's incorrect let me know.
>> - Drop the MFD cell patch, applied by Lee from v4.
>> - Rebase onto iio/testing. The MAINTAINERS entry now follows the MT6323
>> PMIC NVMEM one.
>> - Drop the Assisted-by trailers per the new kernel guidance, and put the
>> disclosure in the cover letter.
>> - Link to v4: https://patch.msgid.link/20260928-rbrue-suez-upstreaming-mt6397-
>> auxadc-v4-0-23533a0d30e3@gmail.com
>>
>> Changes in v4:
>> - Attempt every teardown write even if a previous one fails, so a failed
>> write doesn't leave the buffer, bias, or input powered. Reverses the v3
>> change. The teardown neither checks nor logs errors for failed writes,
>> similar to mt6358_stop_imp_conv(). The next read will rewrite those bits
>> anyway. (Angelo, sashiko-bot, Andy)
>> - Move teardown into mt6397_auxadc_release(), keep error paths out of line
>> with goto, and use mutex_lock() / mutex_unlock() rather than guard().
>> (Jonathan)
>> - Reword the comment above the BATSNS disable prior to ISENSE enable.
>> (Jonathan)
>> - Collect tags.
>> - Link to v3: https://patch.msgid.link/20260920-rbrue-suez-upstreaming-mt6397-
>> auxadc-v3-0-c00edacbee64@gmail.com
>>
>> Changes in v3:
>> - Move the sample loop into its own function, so read_channel() is setup,
>> then a conditional burst, then an unconditional teardown, with no goto
>> mixed with guard(). (Andy, sashiko-bot)
>> - battemp_bias_off() and isense_disable() now return on the first failed
>> write, as mt6323_auxadc_release() does, and twelve other teardowns in
>> drivers/iio that I could find. A failed write can leave the later bits
>> set; the teardown runs at the end of every read, so the next read of that
>> channel clears them. (Andy)
>> - Drop the "if (!ret) ret = err;" accumulators with it. A teardown failure
>> now goes to dev_err() rather than being returned, since the caller cannot
>> act on it, and read_channel() takes the iio_dev so no struct device * is
>> stored. (Andy)
>> - Split battemp_bias(adc, bool on) into battemp_bias_on() and
>> battemp_bias_off(), and drop the bool. (Andy)
>> - Make the SCALE case an if-else. (Andy)
>> - Move the "why a new driver" rationale below the --- marker in patch 2,
>> out of the commit message. (Andy)
>> - Reduce the CHSEL regmap_update_bits() call from four lines to two. (Andy)
>> - Drop the comment above guard(mutex). (Andy)
>> - Say in a comment why lowering START needs no settling delay. The ready
>> bit survives the fall and is cleared by the rise before the next
>> transaction on the PMIC wrapper can observe it. I measured this, and the
>> details are in the reply on 2/3. (Andy)
>> - Cc Luca Leonardo Scorcia with a trailer rather than in prose. (Andy)
>> - Link to v2: https://patch.msgid.link/20260917-rbrue-suez-upstreaming-mt6397-
>> auxadc-v2-0-db35882a6080@gmail.com
>>
>> Changes in v2:
>> - Add justification for this being a new driver rather than folded into
>> mt6323-auxadc.c or mt6359-auxadc.c, in the cover letter and patch 2.
>> - Drop the "ret = ret ?: ..." chains, and let teardown fall through on
>> errors, allowing the chance for all bits to be properly torn down. The
>> errors are now held rather than discarded. (Andy and sashiko-bot)
>> - Run teardown even when per-channel setup fails part-way through, so we
>> don't leave bits enabled that would have been cleared. (sashiko-bot)
>> - Set ISENSE settle time to (1 * USEC_PER_MSEC). (Andy)
>> - Write the two channel descriptors out instead of using a macro. Also
>> gets rid of the padded column. (Andy, Jonathan)
>> - Move the MAINTAINERS entry for the dt-bindings header into patch 1, as
>> the mt6323 series does.
>> - Declare the sample loop counter in the loop, instead of with sum, and
>> split the declaration of sample and ret. (Andy)
>> - Keep the two CHR_CON16 ADCIN bits as BIT()s rather than turning them
>> into values of a GENMASK field. Fix OR operator on the bits, treat them
>> as mutually exclusive. (Jonathan)
>> - The rest of Jonathan's v1 review: two-space indent separating a register's
>> fields from the register, a blank line before the settle times, a lock
>> comment that says why the lock is held, the two CON1 START writes on one
>> line each, the single-call init helper inlined into probe, and { } for the
>> of_device_id sentinel.
>> - Add the additional three CHR_CON16 ADCIN defines that make up the 5
>> single-bit enables. These are currently unused.
>> - Link to v1: https://patch.msgid.link/20260915-rbrue-suez-upstreaming-mt6397-
>> auxadc-v1-0-d35d2ac3d6f0@gmail.com
>>
>> ---
>> Ryan Brue (2):
>> dt-bindings: iio: adc: mediatek,mt6359-auxadc: add mt6397 PMIC AUXADC
>> iio: adc: mt6397-auxadc: add mt6397 PMIC AUXADC driver
>>
>> .../bindings/iio/adc/mediatek,mt6359-auxadc.yaml | 1 +
>> MAINTAINERS | 7 +
>> drivers/iio/adc/Kconfig | 11 +
>> drivers/iio/adc/Makefile | 1 +
>> drivers/iio/adc/mt6397-auxadc.c | 394 +++++++++++++++++++++
>> .../dt-bindings/iio/adc/mediatek,mt6397-auxadc.h | 9 +
>> 6 files changed, 423 insertions(+)
>> ---
>> base-commit: c9dbe2a47f635465c9985b7af74d2ae310e98125
>> change-id: 20260914-rbrue-suez-upstreaming-mt6397-auxadc-5e1228025c50
>>
>> Best regards,
prev parent reply other threads:[~2026-11-17 11:02 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-25 5:18 Ryan Brue
2026-10-25 5:18 ` [PATCH v5 1/2] dt-bindings: iio: adc: mediatek,mt6359-auxadc: add mt6397 PMIC AUXADC Ryan Brue
2026-10-25 5:18 ` [PATCH v5 2/2] iio: adc: mt6397-auxadc: add mt6397 PMIC AUXADC driver Ryan Brue
2026-11-17 10:50 ` AngeloGioacchino Del Regno
2026-10-25 22:44 ` [PATCH v5 0/2] iio: adc: add mt6397 PMIC AUXADC support Jonathan Cameron
2026-11-17 10:56 ` AngeloGioacchino Del Regno
2026-11-17 11:02 ` AngeloGioacchino Del Regno [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=60eeaaf9-57db-4ca7-b4f5-bdec111dcdbb@collabora.com \
--to=angelogioacchino.delregno@collabora.com \
--cc=andriy.shevchenko@intel.com \
--cc=andy@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dlechner@baylibre.com \
--cc=jic23@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=krzysztof.kozlowski@oss.qualcomm.com \
--cc=l.scorcia@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=nuno.sa@analog.com \
--cc=robh@kernel.org \
--cc=rva333@protonmail.com \
--cc=ryanbrue.dev@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®