From: Mikhail Kshevetskiy <mikhail.kshevetskiy@iopsys.eu>
To: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: Ray Liu <ray.liu@airoha.com>, Mark Brown <broonie@kernel.org>,
Jyothi Kumar Seerapu <quic_jseerapu@quicinc.com>,
linux-arm-kernel@lists.infradead.org, linux-spi@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH v4 03/13] spi: airoha: add support of dual/quad wires spi modes
Date: Sat, 23 Aug 2025 16:54:27 +0300 [thread overview]
Message-ID: <68130d82-edbe-4e23-9538-733f9c52123c@iopsys.eu> (raw)
In-Reply-To: <aKl43hTJJVqRE3Rt@lore-rh-laptop>
On 23.08.2025 11:16, Lorenzo Bianconi wrote:
> [...]
>> -static int airoha_snand_write_data(struct airoha_snand_ctrl *as_ctrl, u8 cmd,
>> - const u8 *data, int len)
>> +static int airoha_snand_write_data(struct airoha_snand_ctrl *as_ctrl,
>> + const u8 *data, int len, int buswidth)
>> {
>> int i, data_len;
>> + u8 cmd;
>> +
>> + switch (buswidth) {
>> + case 0:
>> + case 1:
>> + cmd = SNAND_FIFO_TX_BUSWIDTH_SINGLE;
>> + break;
>> + case 2:
>> + cmd = SNAND_FIFO_TX_BUSWIDTH_DUAL;
>> + break;
>> + case 4:
>> + cmd = SNAND_FIFO_TX_BUSWIDTH_QUAD;
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
> Since this is used in airoha_snand_write_data() and in airoha_snand_read_data()
> I guess you can define a routine for it.
It's not the same. It looks similar, but different constants are used
for rx and tx cases.
>
>>
>> for (i = 0; i < len; i += data_len) {
>> int err;
>> @@ -409,16 +433,32 @@ static int airoha_snand_write_data(struct airoha_snand_ctrl *as_ctrl, u8 cmd,
>> return 0;
>> }
>>
>> -static int airoha_snand_read_data(struct airoha_snand_ctrl *as_ctrl, u8 *data,
>> - int len)
>> +static int airoha_snand_read_data(struct airoha_snand_ctrl *as_ctrl,
>> + u8 *data, int len, int buswidth)
>> {
>> int i, data_len;
>> + u8 cmd;
>> +
>> + switch (buswidth) {
>> + case 0:
>> + case 1:
>> + cmd = SNAND_FIFO_RX_BUSWIDTH_SINGLE;
>> + break;
>> + case 2:
>> + cmd = SNAND_FIFO_RX_BUSWIDTH_DUAL;
>> + break;
>> + case 4:
>> + cmd = SNAND_FIFO_RX_BUSWIDTH_QUAD;
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>>
>> for (i = 0; i < len; i += data_len) {
>> int err;
>>
>> data_len = min(len - i, SPI_MAX_TRANSFER_SIZE);
>> - err = airoha_snand_set_fifo_op(as_ctrl, 0xc, data_len);
>> + err = airoha_snand_set_fifo_op(as_ctrl, cmd, data_len);
>> if (err)
>> return err;
>>
>> @@ -895,12 +935,27 @@ static ssize_t airoha_snand_dirmap_write(struct spi_mem_dirmap_desc *desc,
>> static int airoha_snand_exec_op(struct spi_mem *mem,
>> const struct spi_mem_op *op)
>> {
>> - u8 data[8], cmd, opcode = op->cmd.opcode;
>> struct airoha_snand_ctrl *as_ctrl;
>> - int i, err;
>> + char buf[20], *data;
>> + int i, err, op_len, addr_len, dummy_len;
> nit: can you please respect the 'reverse christmas tree' here?
will fix
>
>>
>> as_ctrl = spi_controller_get_devdata(mem->spi->controller);
>>
>> + op_len = op->cmd.nbytes;
>> + addr_len = op->addr.nbytes;
>> + dummy_len = op->dummy.nbytes;
>> +
>> + if (op_len + dummy_len + addr_len > sizeof(buf))
>> + return -EIO;
>> +
>> + data = buf;
>> + for (i = 0; i < op_len; i++)
>> + *data++ = op->cmd.opcode >> (8 * (op_len - i - 1));
>> + for (i = 0; i < addr_len; i++)
>> + *data++ = op->addr.val >> (8 * (addr_len - i - 1));
>> + for (i = 0; i < dummy_len; i++)
>> + *data++ = 0xff;
>> +
>> /* switch to manual mode */
>> err = airoha_snand_set_mode(as_ctrl, SPI_MODE_MANUAL);
>> if (err < 0)
>> @@ -911,40 +966,40 @@ static int airoha_snand_exec_op(struct spi_mem *mem,
>> return err;
>>
>> /* opcode */
>> - err = airoha_snand_write_data(as_ctrl, 0x8, &opcode, sizeof(opcode));
>> + data = buf;
>> + err = airoha_snand_write_data(as_ctrl, data, op_len,
>> + op->cmd.buswidth);
>> if (err)
>> return err;
>>
>> /* addr part */
>> - cmd = opcode == SPI_NAND_OP_GET_FEATURE ? 0x11 : 0x8;
>> - put_unaligned_be64(op->addr.val, data);
>> -
>> - for (i = ARRAY_SIZE(data) - op->addr.nbytes;
>> - i < ARRAY_SIZE(data); i++) {
>> - err = airoha_snand_write_data(as_ctrl, cmd, &data[i],
>> - sizeof(data[0]));
>> + data += op_len;
>> + if (addr_len) {
>> + err = airoha_snand_write_data(as_ctrl, data, addr_len,
>> + op->addr.buswidth);
>> if (err)
>> return err;
>> }
>>
>> /* dummy */
>> - data[0] = 0xff;
>> - for (i = 0; i < op->dummy.nbytes; i++) {
>> - err = airoha_snand_write_data(as_ctrl, 0x8, &data[0],
>> - sizeof(data[0]));
>> + data += addr_len;
>> + if (dummy_len) {
>> + err = airoha_snand_write_data(as_ctrl, data, dummy_len,
>> + op->dummy.buswidth);
>> if (err)
>> return err;
>> }
>>
>> /* data */
>> - if (op->data.dir == SPI_MEM_DATA_IN) {
>> - err = airoha_snand_read_data(as_ctrl, op->data.buf.in,
>> - op->data.nbytes);
>> - if (err)
>> - return err;
>> - } else {
>> - err = airoha_snand_write_data(as_ctrl, 0x8, op->data.buf.out,
>> - op->data.nbytes);
>> + if (op->data.nbytes) {
>> + if (op->data.dir == SPI_MEM_DATA_IN)
>> + err = airoha_snand_read_data(as_ctrl, op->data.buf.in,
>> + op->data.nbytes,
>> + op->data.buswidth);
>> + else
>> + err = airoha_snand_write_data(as_ctrl, op->data.buf.out,
>> + op->data.nbytes,
>> + op->data.buswidth);
>> if (err)
>> return err;
>> }
>> --
>> 2.50.1
>>
next prev parent reply other threads:[~2025-08-23 13:54 UTC|newest]
Thread overview: 65+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-08-20 12:33 [PATCH v3 00/14] spi: airoha: driver fixes & improvements Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 01/14] spi: airoha: return an error for continuous mode dirmap creation cases Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 02/14] spi: airoha: remove unnecessary restriction length Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 03/14] spi: airoha: add support of dual/quad wires spi modes Mikhail Kshevetskiy
2025-08-20 12:48 ` Jyothi Kumar Seerapu
2025-08-20 12:33 ` [PATCH v3 04/14] spi: airoha: remove unnecessary switch to non-dma mode Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 05/14] spi: airoha: unify dirmap read/write code Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 06/14] spi: airoha: switch back to non-dma mode in the case of error Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 07/14] spi: airoha: fix reading/writing of flashes with more than one plane per lun Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 08/14] spi: airoha: support of dualio/quadio flash reading commands Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 09/14] spi: airoha: allow reading/writing of oob area Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 10/14] spi: airoha: buffer must be 0xff-ed before writing Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 11/14] spi: airoha: avoid setting of page/oob sizes in REG_SPI_NFI_PAGEFMT Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 12/14] spi: airoha: reduce the number of modification of REG_SPI_NFI_CNFG and REG_SPI_NFI_SECCUS_SIZE registers Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 13/14] spi: airoha: set custom sector size equal to flash page size Mikhail Kshevetskiy
2025-08-20 12:33 ` [PATCH v3 14/14] spi: airoha: avoid reading flash page settings from SNFI registers during driver startup Mikhail Kshevetskiy
2025-08-21 6:58 ` [PATCH v3 00/14] spi: airoha: driver fixes & improvements Lorenzo Bianconi
2025-08-21 11:13 ` Mikhail Kshevetskiy
2025-08-21 11:34 ` Lorenzo Bianconi
2025-08-21 12:24 ` Mikhail Kshevetskiy
2025-08-22 3:31 ` Mikhail Kshevetskiy
2025-08-22 6:46 ` Lorenzo Bianconi
2025-08-22 11:22 ` Mikhail Kshevetskiy
2025-08-22 13:14 ` Lorenzo Bianconi
2025-08-22 14:36 ` Mikhail Kshevetskiy
2025-08-22 20:00 ` Mikhail Kshevetskiy
2025-08-22 11:27 ` Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 00/13] " Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 01/13] spi: airoha: return an error for continuous mode dirmap creation cases Mikhail Kshevetskiy
2025-08-23 8:04 ` Lorenzo Bianconi
2025-08-23 13:52 ` Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 02/13] spi: airoha: remove unnecessary restriction length Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 03/13] spi: airoha: add support of dual/quad wires spi modes Mikhail Kshevetskiy
2025-08-23 8:16 ` Lorenzo Bianconi
2025-08-23 13:54 ` Mikhail Kshevetskiy [this message]
2025-08-23 14:42 ` Lorenzo Bianconi
2025-08-23 0:16 ` [PATCH v4 04/13] spi: airoha: remove unnecessary switch to non-dma mode Mikhail Kshevetskiy
2025-08-23 8:29 ` Lorenzo Bianconi
2025-08-23 0:16 ` [PATCH v4 05/13] spi: airoha: unify dirmap read/write code Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 06/13] spi: airoha: switch back to non-dma mode in the case of error Mikhail Kshevetskiy
2025-08-23 8:34 ` Lorenzo Bianconi
2025-08-23 0:16 ` [PATCH v4 07/13] spi: airoha: fix reading/writing of flashes with more than one plane per lun Mikhail Kshevetskiy
2025-08-23 8:36 ` Lorenzo Bianconi
2025-08-23 0:16 ` [PATCH v4 08/13] spi: airoha: support of dualio/quadio flash reading commands Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 09/13] spi: airoha: avoid setting of page/oob sizes in REG_SPI_NFI_PAGEFMT Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 10/13] spi: airoha: reduce the number of modification of REG_SPI_NFI_CNFG and REG_SPI_NFI_SECCUS_SIZE registers Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 11/13] spi: airoha: set custom sector size equal to flash page size Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 12/13] spi: airoha: avoid reading flash page settings from SNFI registers during driver startup Mikhail Kshevetskiy
2025-08-23 0:16 ` [PATCH v4 13/13] spi: airoha: buffer must be 0xff-ed before writing Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 00/13] spi: airoha: driver fixes & improvements Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 01/13] spi: airoha: return an error for continuous mode dirmap creation cases Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 02/13] spi: airoha: remove unnecessary restriction length Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 03/13] spi: airoha: add support of dual/quad wires spi modes to exec_op() handler Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 04/13] spi: airoha: remove unnecessary switch to non-dma mode Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 05/13] spi: airoha: switch back to non-dma mode in the case of error Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 06/13] spi: airoha: fix reading/writing of flashes with more than one plane per lun Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 07/13] spi: airoha: unify dirmap read/write code Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 08/13] spi: airoha: support of dualio/quadio flash reading commands Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 09/13] spi: airoha: avoid setting of page/oob sizes in REG_SPI_NFI_PAGEFMT Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 10/13] spi: airoha: reduce the number of modification of REG_SPI_NFI_CNFG and REG_SPI_NFI_SECCUS_SIZE registers Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 11/13] spi: airoha: set custom sector size equal to flash page size Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 12/13] spi: airoha: avoid reading flash page settings from SNFI registers during driver startup Mikhail Kshevetskiy
2025-08-23 16:01 ` [PATCH v5 13/13] spi: airoha: buffer must be 0xff-ed before writing Mikhail Kshevetskiy
2025-08-29 7:14 ` [PATCH v5 00/13] spi: airoha: driver fixes & improvements Mikhail Kshevetskiy
2025-08-29 8:45 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=68130d82-edbe-4e23-9538-733f9c52123c@iopsys.eu \
--to=mikhail.kshevetskiy@iopsys.eu \
--cc=broonie@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=lorenzo@kernel.org \
--cc=quic_jseerapu@quicinc.com \
--cc=ray.liu@airoha.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®