Re: [PATCH v6 13/13] dts: hi3660: Add support for usb on Hikey960

[Chen Yu <chenyu56@huawei.com>]

Hi Rob,

On 2019/4/26 6:00, Rob Herring wrote:
> On Sat, Apr 20, 2019 at 02:40:19PM +0800, Yu Chen wrote:
>> This patch adds support for usb on Hikey960.
>>
>> Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
>> Cc: Wei Xu <xuwei5@hisilicon.com>
>> Cc: Rob Herring <robh+dt@kernel.org>
>> Cc: Mark Rutland <mark.rutland@arm.com>
>> Cc: linux-arm-kernel@lists.infradead.org
>> Cc: John Stultz <john.stultz@linaro.org>
>> Cc: Binghui Wang <wangbinghui@hisilicon.com>
>> Signed-off-by: Yu Chen <chenyu56@huawei.com>
>> ---
>> v2:
>> * Remove device_type property.
>> * Add property "usb-role-switch".
>> v3:
>> * Make node "usb_phy" a subnode of usb3_otg_bc register.
>> * Remove property "typec-vbus-enable-val" of hisi_hikey_usb.
>> v4:
>> * Remove property "hisilicon,usb3-otg-bc-syscon" of usb-phy.
>> ---
>> ---
>>  arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts | 53 ++++++++++++++++
>>  arch/arm64/boot/dts/hisilicon/hi3660.dtsi         | 73 +++++++++++++++++++++++
>>  2 files changed, 126 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
>> index e035cf195b19..d4e11c56b250 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
>> @@ -13,6 +13,7 @@
>>  #include <dt-bindings/gpio/gpio.h>
>>  #include <dt-bindings/input/input.h>
>>  #include <dt-bindings/interrupt-controller/irq.h>
>> +#include <dt-bindings/usb/pd.h>
>>  
>>  / {
>>  	model = "HiKey960";
>> @@ -196,6 +197,26 @@
>>  			method = "smc";
>>  		};
>>  	};
>> +
>> +	hisi_hikey_usb: hisi_hikey_usb {
>> +		compatible = "hisilicon,hikey960_usb";
>> +		typec-vbus-gpios = <&gpio25 2 GPIO_ACTIVE_HIGH>;
>> +		otg-switch-gpios = <&gpio25 6 GPIO_ACTIVE_HIGH>;
>> +		hub-vdd33-en-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&usbhub5734_pmx_func>;
>> +
>> +		port {
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			hikey_usb_ep: endpoint@0 {
>> +				reg = <0>;
>> +				remote-endpoint = <&dwc3_role_switch_notify>;
>> +			};
>> +		};
>> +	};
>> +
>>  };
>>  
>>  /*
>> @@ -526,6 +547,38 @@
>>  &i2c1 {
>>  	status = "okay";
>>  
>> +	rt1711h: rt1711h@4e {
>> +		compatible = "richtek,rt1711h";
> 
> The binding doc for this should state it should have a 'connector' node.
> 
Hi shufan,
Is the 'connector' node an essential node of rt1711h?
Currently it is missing in Documentation/devicetree/bindings/usb/richtek,rt1711h.txt.
Do you think the 'connector' node should add as this patch in the binding doc?

>> +		reg = <0x4e>;
>> +		status = "ok";
> 
> Can drop this, it is the default.
> 
OK.

>> +		interrupt-parent = <&gpio27>;
>> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&usb_cfg_func>;
>> +
>> +		usb_con: connector {
>> +			compatible = "usb-c-connector";
>> +			label = "USB-C";
>> +			data-role = "dual";
>> +			power-role = "dual";
>> +			try-power-role = "sink";
>> +			source-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)>;
>> +			sink-pdos = <PDO_FIXED(5000, 500, PDO_FIXED_USB_COMM)
>> +				PDO_VAR(5000, 5000, 1000)>;
>> +			op-sink-microwatt = <10000000>;
>> +		};
>> +
>> +		port {
> 
> The connector node should have a 'ports' child with 'port@0' being the 
> HS connection.
> 
This port and endpoint of the port are used for role_switch matching by
fwnode_graph_devcon_match. I'm not too sure the 'ports' under connector is used in
rt1711h driver？
Hi shufan_lee,
    Can you confirm this?

>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			rt1711h_ep: endpoint@0 {
>> +				reg = <0>;
>> +				remote-endpoint = <&dwc3_role_switch>;
>> +			};
>> +		};
>> +	};
>> +
>>  	adv7533: adv7533@39 {
>>  		status = "ok";
>>  		compatible = "adi,adv7533";
>> diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> index 2f19e0e5b7cf..173467505ada 100644
>> --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
>> @@ -355,6 +355,12 @@
>>  			#clock-cells = <1>;
>>  		};
>>  
>> +		pmctrl: pmctrl@fff31000 {
>> +			compatible = "hisilicon,hi3660-pmctrl", "syscon";
>> +			reg = <0x0 0xfff31000 0x0 0x1000>;
>> +			#clock-cells = <1>;
>> +		};
>> +
>>  		pmuctrl: crg_ctrl@fff34000 {
>>  			compatible = "hisilicon,hi3660-pmuctrl", "syscon";
>>  			reg = <0x0 0xfff34000 0x0 0x1000>;
>> @@ -1134,5 +1140,72 @@
>>  				};
>>  			};
>>  		};
>> +
>> +		usb3_otg_bc: usb3_otg_bc@ff200000 {
>> +			compatible = "syscon", "simple-mfd";
>> +			reg = <0x0 0xff200000 0x0 0x1000>;
>> +
>> +			usb_phy: usb-phy {
>> +				compatible = "hisilicon,hi3660-usb-phy";
>> +				#phy-cells = <0>;
>> +				hisilicon,pericrg-syscon = <&crg_ctrl>;
>> +				hisilicon,pctrl-syscon = <&pctrl>;
>> +				hisilicon,eye-diagram-param = <0x22466e4>;
>> +			};
>> +		};
>> +
>> +		usb3: hisi_dwc3 {
>> +			compatible = "hisilicon,hi3660-dwc3";
>> +			#address-cells = <2>;
>> +			#size-cells = <2>;
>> +			ranges;
> 
> If there are not any wrapper registers, then get rid of the hisi_dwc3 
> node. For just clocks and resets we just put everything in one node.
> 
I will try to fix this.
>> +
>> +			clocks = <&crg_ctrl HI3660_CLK_ABB_USB>,
>> +				 <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
>> +			clock-names = "clk_usb3phy_ref", "aclk_usb3otg";
>> +
>> +			assigned-clocks = <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
>> +			assigned-clock-rates = <229000000>;
>> +			resets = <&crg_rst 0x90 8>,
>> +				 <&crg_rst 0x90 7>,
>> +				 <&crg_rst 0x90 6>,
>> +				 <&crg_rst 0x90 5>;
>> +
>> +			dwc3: dwc3@ff100000 {
>> +				compatible = "snps,dwc3";
>> +				reg = <0x0 0xff100000 0x0 0x100000>;
>> +				interrupts = <0 159 4>, <0 161 4>;
>> +				phys = <&usb_phy>;
>> +				phy-names = "usb3-phy";
>> +				dr_mode = "otg";
>> +				maximum-speed = "super-speed";
>> +				phy_type = "utmi";
>> +				snps,dis-del-phy-power-chg-quirk;
> 
>> +				snps,lfps_filter_quirk;
>> +				snps,dis_u2_susphy_quirk;
>> +				snps,dis_u3_susphy_quirk;
>> +				snps,tx_de_emphasis_quirk;
>> +				snps,tx_de_emphasis = <1>;
>> +				snps,dis_enblslpm_quirk;
> 
> Pretty sure these aren't documented because we don't use '_' in property 
> names.
> 
Do you mean property as "snps,dis_enblslpm_quirk"? These properties are
documented in Documentation/devicetree/bindings/usb/dwc3.txt.

>> +				snps,gctl-reset-quirk;
>> +				usb-role-switch;
>> +				role-switch-default-host;
>> +
>> +				port {
>> +					#address-cells = <1>;
>> +					#size-cells = <0>;
>> +
>> +					dwc3_role_switch: endpoint@0 {
>> +						reg = <0>;
>> +						remote-endpoint = <&rt1711h_ep>;
>> +					};
>> +
>> +					dwc3_role_switch_notify: endpoint@1 {
>> +						reg = <1>;
>> +						remote-endpoint = <&hikey_usb_ep>;
>> +					};
>> +				};
>> +			};
>> +		};
>>  	};
>>  };
>> -- 
>> 2.15.0-rc2
>>
> 
> .
> 

Thanks
- Yu Chen