From: Lijuan Gao <quic_lijuang@quicinc.com>
To: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Thomas Gleixner <tglx@linutronix.de>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will@kernel.org>, <kernel@quicinc.com>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
Tingguo Cheng <quic_tingguoc@quicinc.com>
Subject: Re: [PATCH v4 6/7] arm64: dts: qcom: add base QCS615 RIDE dts
Date: Fri, 25 Oct 2024 20:14:15 +0800 [thread overview]
Message-ID: <6b70789a-a63b-42e6-beb0-9500cbe99ce7@quicinc.com> (raw)
In-Reply-To: <4bhsuysjm2uwkk52g4pkspiadsf5y4m2afotj7ggo2lnj24ip2@yqkijcdkiloj>
在 10/23/2024 10:09 AM, Bjorn Andersson 写道:
> On Tue, Oct 22, 2024 at 04:54:34PM GMT, Lijuan Gao wrote:
>
> "arm64: dts: qcom: add base QCS615 RIDE dts"
> ^ You already have dts here ^ no need to put it here again
>
>
> I'd suggest that we make the subject "arm64: dts: qcom: Add QCS615 RIDE board"
>
Got it, I will update the title in the next version.
>> Add initial support for Qualcomm QCS615 RIDE board and enable
>> the QCS615 RIDE board to shell with uart console.
>>
>> [Tingguo: added regulator nodes]
>
> Are you saying:
> - Lijuan wrote the patch
> - Lijuan signed the certificate of origin (i.e. he's allowed to
> contribute its content)
> - Tingguo added regulator nodes
> - Tingguo signed the certificate of origin (i.e. patch was based on work
> that was certified)
>
> Or are you saying:
> "Tingguo and I developed this patch in pair programming fashion"
>
> If so, I'd suggest dropping the "[Tingguo:...]" line.
>
Yes, I wrote the base patch and Tingguo added the regulator nodes. I
will update the commit message with "Written with help from Tingguo
Cheng (added regulator nodes)" as suggested in the initial dtsi comments
>> Co-developed-by: Tingguo Cheng <quic_tingguoc@quicinc.com>
>> Signed-off-by: Tingguo Cheng <quic_tingguoc@quicinc.com>
>> Signed-off-by: Lijuan Gao <quic_lijuang@quicinc.com>
>> ---
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> arch/arm64/boot/dts/qcom/qcs615-ride.dts | 219 +++++++++++++++++++++++++++++++
>> 2 files changed, 220 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 065bb19481c1..f14643187cac 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -110,6 +110,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
>> +dtb-$(CONFIG_ARCH_QCOM) += qcs615-ride.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
>> new file mode 100644
>> index 000000000000..ee6cab3924a6
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts
>> @@ -0,0 +1,219 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2024, Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>> +#include "qcs615.dtsi"
>> +/ {
>> + model = "Qualcomm Technologies, Inc. QCS615 Ride";
>> + compatible = "qcom,qcs615-ride", "qcom,qcs615";
>> + chassis-type = "embedded";
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>> +
>> + clocks {
>> + sleep_clk: sleep-clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <32000>;
>> + #clock-cells = <0>;
>> + };
>> +
>> + xo_board_clk: xo-board-clk {
>> + compatible = "fixed-clock";
>> + clock-frequency = <38400000>;
>> + #clock-cells = <0>;
>> + };
>> + };
>> +};
>> +
>> +&apps_rsc {
>> + regulators-0 {
>> + compatible = "qcom,pm8150-rpmh-regulators";
>> + qcom,pmic-id = "a";
>> +
>> + vreg_s3a: smps3 {
>
> You don't reference any of these regulators.
>
> Can you please confirm that when you boot the qcs615 ride device with
> this dtb it actually boots with a debug uart and does not crash when the
> regulator framework disable all these "unused" regulators?
>
> Regards,
> Bjorn
>
Yes, the device booted successfully. The regulator is part of Tingguo’s
PMIC-related modifications. The RPMhpd, which UART depends on, is also
part of this series of changes. The regulator will be used later, so
both of them were added.
>> + regulator-name = "vreg_s3a";
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <650000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_s4a: smps4 {
>> + regulator-name = "vreg_s4a";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1829000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_s5a: smps5 {
>> + regulator-name = "vreg_s5a";
>> + regulator-min-microvolt = <1896000>;
>> + regulator-max-microvolt = <2040000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_s6a: smps6 {
>> + regulator-name = "vreg_s6a";
>> + regulator-min-microvolt = <1304000>;
>> + regulator-max-microvolt = <1404000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l1a: ldo1 {
>> + regulator-name = "vreg_l1a";
>> + regulator-min-microvolt = <488000>;
>> + regulator-max-microvolt = <852000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l2a: ldo2 {
>> + regulator-name = "vreg_l2a";
>> + regulator-min-microvolt = <1650000>;
>> + regulator-max-microvolt = <3100000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l3a: ldo3 {
>> + regulator-name = "vreg_l3a";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1248000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l5a: ldo5 {
>> + regulator-name = "vreg_l5a";
>> + regulator-min-microvolt = <875000>;
>> + regulator-max-microvolt = <975000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l7a: ldo7 {
>> + regulator-name = "vreg_l7a";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1900000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l8a: ldo8 {
>> + regulator-name = "vreg_l8a";
>> + regulator-min-microvolt = <1150000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l10a: ldo10 {
>> + regulator-name = "vreg_l10a";
>> + regulator-min-microvolt = <2950000>;
>> + regulator-max-microvolt = <3312000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l11a: ldo11 {
>> + regulator-name = "vreg_l11a";
>> + regulator-min-microvolt = <1232000>;
>> + regulator-max-microvolt = <1260000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l12a: ldo12 {
>> + regulator-name = "vreg_l12a";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1890000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l13a: ldo13 {
>> + regulator-name = "vreg_l13a";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3230000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l15a: ldo15 {
>> + regulator-name = "vreg_l15a";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1904000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l16a: ldo16 {
>> + regulator-name = "vreg_l16a";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3312000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l17a: ldo17 {
>> + regulator-name = "vreg_l17a";
>> + regulator-min-microvolt = <2950000>;
>> + regulator-max-microvolt = <3312000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> + };
>> +};
>> +
>> +&gcc {
>> + clocks = <&rpmhcc RPMH_CXO_CLK>,
>> + <&rpmhcc RPMH_CXO_CLK_A>,
>> + <&sleep_clk>;
>> +};
>> +
>> +&qupv3_id_0 {
>> + status = "okay";
>> +};
>> +
>> +&rpmhcc {
>> + clocks = <&xo_board_clk>;
>> +};
>> +
>> +&uart0 {
>> + status = "okay";
>> +};
>> +
>> +&watchdog {
>> + clocks = <&sleep_clk>;
>> +};
>>
>> --
>> 2.46.0
>>
--
Thx and BRs
Lijuan Gao
next prev parent reply other threads:[~2024-10-25 12:14 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-10-22 8:54 [PATCH v4 0/7] Add initial support for QCS615 SoC and QCS615 RIDE board Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 1/7] dt-bindings: arm: qcom: document QCS615 and the reference board Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 2/7] dt-bindings: arm: qcom,ids: add SoC ID for QCS615 Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 3/7] dt-bindings: qcom,pdc: document QCS615 Power Domain Controller Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 4/7] soc: qcom: socinfo: Add QCS615 SoC ID table entry Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 5/7] arm64: dts: qcom: add initial support for QCS615 DTSI Lijuan Gao
2024-10-23 2:30 ` Bjorn Andersson
2024-10-25 11:36 ` Lijuan Gao
2024-10-22 8:54 ` [PATCH v4 6/7] arm64: dts: qcom: add base QCS615 RIDE dts Lijuan Gao
2024-10-23 2:09 ` Bjorn Andersson
2024-10-25 12:14 ` Lijuan Gao [this message]
2024-10-22 8:54 ` [PATCH v4 7/7] arm64: defconfig: enable clock controller, interconnect and pinctrl for QCS615 Lijuan Gao
2024-10-23 2:42 ` Bjorn Andersson
2024-10-23 4:16 ` (subset) [PATCH v4 0/7] Add initial support for QCS615 SoC and QCS615 RIDE board Bjorn Andersson
2024-10-24 16:33 ` Rob Herring (Arm)
2024-10-25 8:10 ` Lijuan Gao
2024-10-25 11:16 ` Dmitry Baryshkov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6b70789a-a63b-42e6-beb0-9500cbe99ce7@quicinc.com \
--to=quic_lijuang@quicinc.com \
--cc=andersson@kernel.org \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kernel@quicinc.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_tingguoc@quicinc.com \
--cc=robh@kernel.org \
--cc=tglx@linutronix.de \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®