mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: "Michal Piotrowski" <michal.k.k.piotrowski@gmail.com>
To: "Zoltan Boszormenyi" <zboszor@dunaweb.hu>
Cc: linux-kernel <linux-kernel@vger.kernel.org>,
	"IDE/ATA development list" <linux-ide@vger.kernel.org>
Subject: Re: Bad CD disk disables IDE DMA
Date: Thu, 16 Aug 2007 10:17:28 +0200	[thread overview]
Message-ID: <6bffcb0e0708160117m31b6edc6ta277b6ddf2d894f6@mail.gmail.com> (raw)
In-Reply-To: <46C2F526.30005@dunaweb.hu>

Hi Zoltan,

On 15/08/07, Zoltan Boszormenyi <zboszor@dunaweb.hu> wrote:
> Hi,
>
> I noticed that a bad CD of mine makes DMA disabled:
>
> hda: selected mode 0x44
> hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
> hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
> hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
> hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hda: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
> hda: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
> ide: failed opcode was: unknown
> hda: DMA disabled
> hda: ide_intr: huh? expected NULL handler on exit
> hda: ATAPI reset complete
>
> Every time I put the said CD into to drive and DMA is on, I get the
> above messages.

This might be intended.

> Two things are interesting: first, it gets mounted correctly and
> readable and
> second, when DMA was already disabled no such messages occur in the logs.
> Anyhow, I would need DMA to correctly burn CDs/DVDs...
> What can I do besides manually re-enable DMA?
> All other disks I have tried behave perfectly.
> This happened on 2.6.22[-rcX], 2.6.23-rc3-git1 and 2.6.20-1.2962.fc6.
> This is on a Fedora Core 6 system. CD/DVD is using the old IDE drivers:
>
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
> NFORCE-MCP55: chipset revision 161
> NFORCE-MCP55: not 100% native mode: will probe irqs later
> NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
> NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
>     ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
> Probing IDE interface ide0...
> hda: PIONEER DVD-RW DVR-111L, ATAPI CD/DVD-ROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> Probing IDE interface ide1...
> ide-floppy driver 0.99.newide
>
> $ cat /proc/ide/amd74xx
> ----------AMD BusMastering IDE Configuration----------------
> Driver Version:                     2.13
> South Bridge:                       0000:00:04.0
> Revision:                           IDE 0xa1
> Highest DMA rate:                   UDMA133
> BM-DMA base:                        0xf000
> PCI clock:                          33.3MHz
> -----------------------Primary IDE-------Secondary IDE------
> Prefetch Buffer:              yes                 yes
> Post Write Buffer:            yes                 yes
> Enabled:                      yes                  no
> Simplex only:                  no                 yes
> Cable Type:                   80w                 80w
> -------------------drive0----drive1----drive2----drive3-----
> Transfer Mode:        PIO       DMA       DMA       DMA
> Address Setup:       30ns      90ns      90ns      90ns
> Cmd Active:          90ns      90ns     300ns     300ns
> Cmd Recovery:        30ns      30ns     300ns     300ns
> Data Active:         90ns     330ns     330ns     330ns
> Data Recovery:       30ns     270ns     270ns     270ns
> Cycle Time:         120ns     600ns     600ns     600ns
> Transfer Rate:   16.6MB/s   3.3MB/s   3.3MB/s   3.3MB/s
>
> Best regards,
> Zoltán Böszörményi

Regards,
Michal

-- 
LOG
http://www.stardust.webpages.pl/log/

  reply	other threads:[~2007-08-16  8:17 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2007-08-15 12:44 Zoltan Boszormenyi
2007-08-16  8:17 ` Michal Piotrowski [this message]
2007-08-16 10:58   ` Zoltan Boszormenyi
2007-08-16 12:14     ` Zoltan Boszormenyi
     [not found] <8Squ5-2cU-19@gated-at.bofh.it>
     [not found] ` <8SIKl-5IK-13@gated-at.bofh.it>
2007-08-16 12:11   ` Bodo Eggert
2007-08-16 12:39     ` Zoltan Boszormenyi
2007-08-19  8:33       ` Zoltan Boszormenyi

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=6bffcb0e0708160117m31b6edc6ta277b6ddf2d894f6@mail.gmail.com \
    --to=michal.k.k.piotrowski@gmail.com \
    --cc=linux-ide@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=zboszor@dunaweb.hu \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®