From: Greg Ungerer <gerg@linux-m68k.org>
To: afzal mohammed <afzal.mohd.ma@gmail.com>,
linux-m68k@lists.linux-m68k.org, linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>,
Geert Uytterhoeven <geert@linux-m68k.org>,
Finn Thain <fthain@telegraphics.com.au>
Subject: Re: [PATCH v2 06/18] m68k: Replace setup_irq() by request_irq()
Date: Wed, 26 Feb 2020 10:42:00 +1000 [thread overview]
Message-ID: <73c3ad08-963d-fea2-91d7-b06e4ef8d3ef@linux-m68k.org> (raw)
In-Reply-To: <00b0bf964278dd0bb3e093283994399ff796cca5.1582471508.git.afzal.mohd.ma@gmail.com>
Hi Afzal,
On 24/2/20 10:50 am, afzal mohammed wrote:
> request_irq() is preferred over setup_irq(). The early boot setup_irq()
> invocations happen either via 'init_IRQ()' or 'time_init()', while
> memory allocators are ready by 'mm_init()'.
>
> Per tglx[1], setup_irq() existed in olden days when allocators were not
> ready by the time early interrupts were initialized.
>
> Hence replace setup_irq() by request_irq().
>
> Seldom remove_irq() usage has been observed coupled with setup_irq(),
> wherever that has been found, it too has been replaced by free_irq().
>
> [1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
>
> Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
> Tested-by: Greg Ungerer <gerg@linux-m68k.org> # ColdFire
> ---
>
> v2:
> * Replace pr_err("request_irq() on %s failed" by
> pr_err("%s: request_irq() failed"
> * Commit message massage
> * remove now irrelevant comment lines at 3 places
>
> arch/m68k/68000/timers.c | 11 ++---------
> arch/m68k/coldfire/pit.c | 11 ++---------
> arch/m68k/coldfire/sltimers.c | 19 +++++--------------
> arch/m68k/coldfire/timers.c | 21 +++++----------------
> 4 files changed, 14 insertions(+), 48 deletions(-)
>
> diff --git a/arch/m68k/68000/timers.c b/arch/m68k/68000/timers.c
> index 71ddb4c98726..55a76a2d3d58 100644
> --- a/arch/m68k/68000/timers.c
> +++ b/arch/m68k/68000/timers.c
> @@ -68,14 +68,6 @@ static irqreturn_t hw_tick(int irq, void *dummy)
>
> /***************************************************************************/
>
> -static struct irqaction m68328_timer_irq = {
> - .name = "timer",
> - .flags = IRQF_TIMER,
> - .handler = hw_tick,
> -};
> -
> -/***************************************************************************/
> -
> static u64 m68328_read_clk(struct clocksource *cs)
> {
> unsigned long flags;
> @@ -106,7 +98,8 @@ void hw_timer_init(irq_handler_t handler)
> TCTL = 0;
>
> /* set ISR */
> - setup_irq(TMR_IRQ_NUM, &m68328_timer_irq);
> + if (request_irq(TMR_IRQ_NUM, hw_tick, IRQF_TIMER, "timer", NULL))
> + pr_err("%s: request_irq() failed\n", "timer");
Why not just:
pr_err("timer: request_irq() failed\n");
And maybe would it be useful to print out the error return code from a
failed request_irq()? What about displaying the requested IRQ number as well?
Just a thought.
Regards
Greg
> /* Restart mode, Enable int, Set clock source */
> TCTL = TCTL_OM | TCTL_IRQEN | CLOCK_SOURCE;
> diff --git a/arch/m68k/coldfire/pit.c b/arch/m68k/coldfire/pit.c
> index eb6f16b0e2e6..604acd658dec 100644
> --- a/arch/m68k/coldfire/pit.c
> +++ b/arch/m68k/coldfire/pit.c
> @@ -111,14 +111,6 @@ static irqreturn_t pit_tick(int irq, void *dummy)
>
> /***************************************************************************/
>
> -static struct irqaction pit_irq = {
> - .name = "timer",
> - .flags = IRQF_TIMER,
> - .handler = pit_tick,
> -};
> -
> -/***************************************************************************/
> -
> static u64 pit_read_clk(struct clocksource *cs)
> {
> unsigned long flags;
> @@ -156,7 +148,8 @@ void hw_timer_init(irq_handler_t handler)
> cf_pit_clockevent.min_delta_ticks = 0x3f;
> clockevents_register_device(&cf_pit_clockevent);
>
> - setup_irq(MCF_IRQ_PIT1, &pit_irq);
> + if (request_irq(MCF_IRQ_PIT1, pit_tick, IRQF_TIMER, "timer", NULL))
> + pr_err("%s: request_irq() failed\n", "timer");
>
> clocksource_register_hz(&pit_clk, FREQ);
> }
> diff --git a/arch/m68k/coldfire/sltimers.c b/arch/m68k/coldfire/sltimers.c
> index 1b11e7bacab3..c5d5862e1d2b 100644
> --- a/arch/m68k/coldfire/sltimers.c
> +++ b/arch/m68k/coldfire/sltimers.c
> @@ -50,18 +50,14 @@ irqreturn_t mcfslt_profile_tick(int irq, void *dummy)
> return IRQ_HANDLED;
> }
>
> -static struct irqaction mcfslt_profile_irq = {
> - .name = "profile timer",
> - .flags = IRQF_TIMER,
> - .handler = mcfslt_profile_tick,
> -};
> -
> void mcfslt_profile_init(void)
> {
> printk(KERN_INFO "PROFILE: lodging TIMER 1 @ %dHz as profile timer\n",
> PROFILEHZ);
>
> - setup_irq(MCF_IRQ_PROFILER, &mcfslt_profile_irq);
> + if (request_irq(MCF_IRQ_PROFILER, mcfslt_profile_tick, IRQF_TIMER,
> + "profile timer", NULL))
> + pr_err("%s: request_irq() failed\n", "profile timer");
>
> /* Set up TIMER 2 as high speed profile clock */
> __raw_writel(MCF_BUSCLK / PROFILEHZ - 1, PA(MCFSLT_STCNT));
> @@ -92,12 +88,6 @@ static irqreturn_t mcfslt_tick(int irq, void *dummy)
> return timer_interrupt(irq, dummy);
> }
>
> -static struct irqaction mcfslt_timer_irq = {
> - .name = "timer",
> - .flags = IRQF_TIMER,
> - .handler = mcfslt_tick,
> -};
> -
> static u64 mcfslt_read_clk(struct clocksource *cs)
> {
> unsigned long flags;
> @@ -140,7 +130,8 @@ void hw_timer_init(irq_handler_t handler)
> mcfslt_cnt = mcfslt_cycles_per_jiffy;
>
> timer_interrupt = handler;
> - setup_irq(MCF_IRQ_TIMER, &mcfslt_timer_irq);
> + if (request_irq(MCF_IRQ_TIMER, mcfslt_tick, IRQF_TIMER, "timer", NULL))
> + pr_err("%s: request_irq() failed\n", "timer");
>
> clocksource_register_hz(&mcfslt_clk, MCF_BUSCLK);
>
> diff --git a/arch/m68k/coldfire/timers.c b/arch/m68k/coldfire/timers.c
> index 227aa5d13709..52294c1f01f8 100644
> --- a/arch/m68k/coldfire/timers.c
> +++ b/arch/m68k/coldfire/timers.c
> @@ -82,14 +82,6 @@ static irqreturn_t mcftmr_tick(int irq, void *dummy)
>
> /***************************************************************************/
>
> -static struct irqaction mcftmr_timer_irq = {
> - .name = "timer",
> - .flags = IRQF_TIMER,
> - .handler = mcftmr_tick,
> -};
> -
> -/***************************************************************************/
> -
> static u64 mcftmr_read_clk(struct clocksource *cs)
> {
> unsigned long flags;
> @@ -134,7 +126,8 @@ void hw_timer_init(irq_handler_t handler)
>
> timer_interrupt = handler;
> init_timer_irq();
> - setup_irq(MCF_IRQ_TIMER, &mcftmr_timer_irq);
> + if (request_irq(MCF_IRQ_TIMER, mcftmr_tick, IRQF_TIMER, "timer", NULL))
> + pr_err("%s: request_irq() failed\n", "timer");
>
> #ifdef CONFIG_HIGHPROFILE
> coldfire_profile_init();
> @@ -170,12 +163,6 @@ irqreturn_t coldfire_profile_tick(int irq, void *dummy)
>
> /***************************************************************************/
>
> -static struct irqaction coldfire_profile_irq = {
> - .name = "profile timer",
> - .flags = IRQF_TIMER,
> - .handler = coldfire_profile_tick,
> -};
> -
> void coldfire_profile_init(void)
> {
> printk(KERN_INFO "PROFILE: lodging TIMER2 @ %dHz as profile timer\n",
> @@ -188,7 +175,9 @@ void coldfire_profile_init(void)
> __raw_writew(MCFTIMER_TMR_ENORI | MCFTIMER_TMR_CLK16 |
> MCFTIMER_TMR_RESTART | MCFTIMER_TMR_ENABLE, PA(MCFTIMER_TMR));
>
> - setup_irq(MCF_IRQ_PROFILER, &coldfire_profile_irq);
> + if (request_irq(MCF_IRQ_PROFILER, coldfire_profile_tick, IRQF_TIMER,
> + "profile timer", NULL))
> + pr_err("%s: request_irq() failed\n", "profile timer");
> }
>
> /***************************************************************************/
>
next prev parent reply other threads:[~2020-02-26 0:42 UTC|newest]
Thread overview: 51+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-24 0:47 [PATCH v2 00/18] genirq: Remove setup_irq() afzal mohammed
2020-02-24 0:48 ` [PATCH v2 01/18] alpha: replace setup_irq() by request_irq() afzal mohammed
2020-02-24 0:49 ` [PATCH v2 02/18] ARM: " afzal mohammed
2020-02-24 10:13 ` Lubomir Rintel
2020-02-26 16:31 ` Tony Lindgren
2020-02-24 0:49 ` [PATCH v2 03/18] c6x: " afzal mohammed
2020-02-24 0:49 ` [PATCH v2 04/18] hexagon: " afzal mohammed
2020-02-24 0:49 ` [PATCH v2 05/18] ia64: " afzal mohammed
2020-02-24 0:50 ` [PATCH v2 06/18] m68k: Replace " afzal mohammed
2020-02-26 0:42 ` Greg Ungerer [this message]
2020-02-26 1:11 ` Finn Thain
2020-02-26 2:11 ` Greg Ungerer
2020-02-26 6:39 ` Finn Thain
2020-02-26 12:26 ` Greg Ungerer
2020-02-26 22:31 ` Finn Thain
2020-02-27 6:37 ` Greg Ungerer
2020-02-27 22:19 ` Finn Thain
2020-02-27 8:18 ` afzal mohammed
2020-02-27 8:32 ` Geert Uytterhoeven
2020-02-27 12:06 ` afzal mohammed
2020-02-27 22:38 ` Finn Thain
2020-02-29 12:41 ` afzal mohammed
2020-02-28 7:05 ` Greg Ungerer
2020-02-29 12:47 ` afzal mohammed
2020-02-29 13:15 ` afzal mohammed
2020-02-29 23:11 ` Finn Thain
2020-03-01 1:05 ` afzal mohammed
2020-03-01 3:26 ` Finn Thain
2020-03-01 6:13 ` afzal mohammed
2020-03-02 6:26 ` Finn Thain
2020-03-04 1:24 ` afzal mohammed
2020-02-24 0:50 ` [PATCH v2 07/18] microblaze: " afzal mohammed
2020-02-24 0:50 ` [PATCH v2 08/18] MIPS: " afzal mohammed
2020-02-24 0:51 ` [PATCH v2 09/18] parisc: " afzal mohammed
2020-02-24 0:51 ` [PATCH v2 10/18] powerpc: " afzal mohammed
2020-02-24 0:51 ` [PATCH v2 11/18] s390: replace " afzal mohammed
2020-02-24 0:51 ` [PATCH v2 12/18] sh: " afzal mohammed
2020-02-24 0:52 ` [PATCH v2 13/18] unicore32: " afzal mohammed
2020-02-24 0:52 ` [PATCH v2 14/18] x86: Replace " afzal mohammed
2020-02-24 0:52 ` [PATCH v2 15/18] xtensa: replace " afzal mohammed
2020-02-24 0:52 ` [PATCH v2 16/18] clocksource: Replace " afzal mohammed
2020-02-25 2:52 ` kbuild test robot
2020-02-25 7:51 ` afzal mohammed
2020-02-27 10:59 ` [PATCH v3 " afzal mohammed
2020-02-27 11:18 ` Daniel Lezcano
2020-03-12 6:48 ` [PATCH v4] clocksource/drivers/timer-cs5535: request irq with non-NULL dev_id afzal mohammed
2020-03-12 7:10 ` afzal mohammed
2020-03-12 18:23 ` Daniel Lezcano
2020-03-19 8:47 ` [tip: timers/core] clocksource/drivers/timer-cs5535: Request " tip-bot2 for afzal mohammed
2020-02-24 0:53 ` [PATCH v2 17/18] irqchip: Replace setup_irq() by request_irq() afzal mohammed
2020-02-24 0:53 ` [PATCH v2 18/18] genirq: Remove setup_irq() and remove_irq() afzal mohammed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=73c3ad08-963d-fea2-91d7-b06e4ef8d3ef@linux-m68k.org \
--to=gerg@linux-m68k.org \
--cc=afzal.mohd.ma@gmail.com \
--cc=fthain@telegraphics.com.au \
--cc=geert@linux-m68k.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-m68k@lists.linux-m68k.org \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®