[PATCH v2 7/8] platform/x86: Add driver for ACPI INT0002 Virtual GPIO device

["Rafael J. Wysocki" <rjw@rjwysocki.net>]

From: Hans de Goede <hdegoede@redhat.com>

Some peripherals on Bay Trail and Cherry Trail platforms signal a
Power Management Event (PME) to the Power Management Controller (PMC)
to wakeup the system. When this happens software needs to explicitly
clear the PME bus 0 status bit in the GPE0a_STS register to avoid an
IRQ storm on IRQ 9.

This is modelled in ACPI through the INT0002 ACPI device, which is
called a "Virtual GPIO controller" in ACPI because it defines the
event handler to call when the PME triggers through _AEI and _L02
methods as would be done for a real GPIO interrupt in ACPI.

This commit adds a driver which registers the Virtual GPIOs expected
by the DSDT on these devices, letting gpiolib-acpi claim the
virtual GPIO and install a GPIO-interrupt handler which call the _L02
handler as it would for a real GPIO controller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
---
 drivers/platform/x86/Kconfig               |  19 +++
 drivers/platform/x86/Makefile              |   1 +
 drivers/platform/x86/intel_int0002_vgpio.c | 219 +++++++++++++++++++++++++++++
 3 files changed, 239 insertions(+)
 create mode 100644 drivers/platform/x86/intel_int0002_vgpio.c

diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
index 8489020ecf44..a3ccc3c795a5 100644
--- a/drivers/platform/x86/Kconfig
+++ b/drivers/platform/x86/Kconfig
@@ -794,6 +794,25 @@ config INTEL_CHT_INT33FE
 	  This driver instantiates i2c-clients for these, so that standard
 	  i2c drivers for these chips can bind to the them.
 
+config INTEL_INT0002_VGPIO
+	tristate "Intel ACPI INT0002 Virtual GPIO driver"
+	depends on GPIOLIB && ACPI
+	select GPIOLIB_IRQCHIP
+	---help---
+	  Some peripherals on Bay Trail and Cherry Trail platforms signal a
+	  Power Management Event (PME) to the Power Management Controller (PMC)
+	  to wakeup the system. When this happens software needs to explicitly
+	  clear the PME bus 0 status bit in the GPE0a_STS register to avoid an
+	  IRQ storm on IRQ 9.
+
+	  This is modelled in ACPI through the INT0002 ACPI device, which is
+	  called a "Virtual GPIO controller" in ACPI because it defines the
+	  event handler to call when the PME triggers through _AEI and _L02
+	  methods as would be done for a real GPIO interrupt in ACPI.
+
+	  To compile this driver as a module, choose M here: the module will
+	  be called intel_int0002_vgpio.
+
 config INTEL_HID_EVENT
 	tristate "INTEL HID Event"
 	depends on ACPI
diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
index 182a3ed6605a..ab22ce77fb66 100644
--- a/drivers/platform/x86/Makefile
+++ b/drivers/platform/x86/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_TOSHIBA_BT_RFKILL)	+= toshiba_bluetooth.o
 obj-$(CONFIG_TOSHIBA_HAPS)	+= toshiba_haps.o
 obj-$(CONFIG_TOSHIBA_WMI)	+= toshiba-wmi.o
 obj-$(CONFIG_INTEL_CHT_INT33FE)	+= intel_cht_int33fe.o
+obj-$(CONFIG_INTEL_INT0002_VGPIO) += intel_int0002_vgpio.o
 obj-$(CONFIG_INTEL_HID_EVENT)	+= intel-hid.o
 obj-$(CONFIG_INTEL_VBTN)	+= intel-vbtn.o
 obj-$(CONFIG_INTEL_SCU_IPC)	+= intel_scu_ipc.o
diff --git a/drivers/platform/x86/intel_int0002_vgpio.c b/drivers/platform/x86/intel_int0002_vgpio.c
new file mode 100644
index 000000000000..92dc230ef5b2
--- /dev/null
+++ b/drivers/platform/x86/intel_int0002_vgpio.c
@@ -0,0 +1,219 @@
+/*
+ * Intel INT0002 "Virtual GPIO" driver
+ *
+ * Copyright (C) 2017 Hans de Goede <hdegoede@redhat.com>
+ *
+ * Loosely based on android x86 kernel code which is:
+ *
+ * Copyright (c) 2014, Intel Corporation.
+ *
+ * Author: Dyut Kumar Sil <dyut.k.sil@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Some peripherals on Bay Trail and Cherry Trail platforms signal a Power
+ * Management Event (PME) to the Power Management Controller (PMC) to wakeup
+ * the system. When this happens software needs to clear the PME bus 0 status
+ * bit in the GPE0a_STS register to avoid an IRQ storm on IRQ 9.
+ *
+ * This is modelled in ACPI through the INT0002 ACPI device, which is
+ * called a "Virtual GPIO controller" in ACPI because it defines the event
+ * handler to call when the PME triggers through _AEI and _L02 / _E02
+ * methods as would be done for a real GPIO interrupt in ACPI. Note this
+ * is a hack to define an AML event handler for the PME while using existing
+ * ACPI mechanisms, this is not a real GPIO at all.
+ *
+ * This driver will bind to the INT0002 device, and register as a GPIO
+ * controller, letting gpiolib-acpi.c call the _L02 handler as it would
+ * for a real GPIO controller.
+ */
+
+#include <linux/acpi.h>
+#include <linux/bitmap.h>
+#include <linux/gpio/driver.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/suspend.h>
+
+#include <asm/cpu_device_id.h>
+#include <asm/intel-family.h>
+
+#define DRV_NAME			"INT0002 Virtual GPIO"
+
+/* For some reason the virtual GPIO pin tied to the GPE is numbered pin 2 */
+#define GPE0A_PME_B0_VIRT_GPIO_PIN	2
+
+#define GPE0A_PME_B0_STS_BIT		BIT(13)
+#define GPE0A_PME_B0_EN_BIT		BIT(13)
+#define GPE0A_STS_PORT			0x420
+#define GPE0A_EN_PORT			0x428
+
+#define ICPU(model)	{ X86_VENDOR_INTEL, 6, model, X86_FEATURE_ANY, }
+
+static const struct x86_cpu_id int0002_cpu_ids[] = {
+/*
+ * Limit ourselves to Cherry Trail for now, until testing shows we
+ * need to handle the INT0002 device on Baytrail too.
+ *	ICPU(INTEL_FAM6_ATOM_SILVERMONT1),	 * Valleyview, Bay Trail *
+ */
+	ICPU(INTEL_FAM6_ATOM_AIRMONT),		/* Braswell, Cherry Trail */
+	{}
+};
+
+/*
+ * As this is not a real GPIO at all, but just a hack to model an event in
+ * ACPI the get / set functions are dummy functions.
+ */
+
+static int int0002_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	return 0;
+}
+
+static void int0002_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			     int value)
+{
+}
+
+static int int0002_gpio_direction_output(struct gpio_chip *chip,
+					 unsigned int offset, int value)
+{
+	return 0;
+}
+
+static void int0002_irq_ack(struct irq_data *data)
+{
+	outl(GPE0A_PME_B0_STS_BIT, GPE0A_STS_PORT);
+}
+
+static void int0002_irq_unmask(struct irq_data *data)
+{
+	u32 gpe_en_reg;
+
+	gpe_en_reg = inl(GPE0A_EN_PORT);
+	gpe_en_reg |= GPE0A_PME_B0_EN_BIT;
+	outl(gpe_en_reg, GPE0A_EN_PORT);
+}
+
+static void int0002_irq_mask(struct irq_data *data)
+{
+	u32 gpe_en_reg;
+
+	gpe_en_reg = inl(GPE0A_EN_PORT);
+	gpe_en_reg &= ~GPE0A_PME_B0_EN_BIT;
+	outl(gpe_en_reg, GPE0A_EN_PORT);
+}
+
+static irqreturn_t int0002_irq(int irq, void *data)
+{
+	struct gpio_chip *chip = data;
+	u32 gpe_sts_reg;
+
+	gpe_sts_reg = inl(GPE0A_STS_PORT);
+	if (!(gpe_sts_reg & GPE0A_PME_B0_STS_BIT))
+		return IRQ_NONE;
+
+	generic_handle_irq(irq_find_mapping(chip->irqdomain,
+					    GPE0A_PME_B0_VIRT_GPIO_PIN));
+
+	pm_system_wakeup();
+
+	return IRQ_HANDLED;
+}
+
+static struct irq_chip int0002_irqchip = {
+	.name			= DRV_NAME,
+	.irq_ack		= int0002_irq_ack,
+	.irq_mask		= int0002_irq_mask,
+	.irq_unmask		= int0002_irq_unmask,
+};
+
+static int int0002_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	const struct x86_cpu_id *cpu_id;
+	struct gpio_chip *chip;
+	int irq, ret;
+
+	/* Menlow has a different INT0002 device? <sigh> */
+	cpu_id = x86_match_cpu(int0002_cpu_ids);
+	if (!cpu_id)
+		return -ENODEV;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(dev, "Error getting IRQ: %d\n", irq);
+		return irq;
+	}
+
+	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->label = DRV_NAME;
+	chip->parent = dev;
+	chip->owner = THIS_MODULE;
+	chip->get = int0002_gpio_get;
+	chip->set = int0002_gpio_set;
+	chip->direction_input = int0002_gpio_get;
+	chip->direction_output = int0002_gpio_direction_output;
+	chip->base = -1;
+	chip->ngpio = GPE0A_PME_B0_VIRT_GPIO_PIN + 1;
+	chip->irq_need_valid_mask = true;
+
+	ret = devm_gpiochip_add_data(&pdev->dev, chip, NULL);
+	if (ret) {
+		dev_err(dev, "Error adding gpio chip: %d\n", ret);
+		return ret;
+	}
+
+	bitmap_clear(chip->irq_valid_mask, 0, GPE0A_PME_B0_VIRT_GPIO_PIN);
+
+	/*
+	 * We manually request the irq here instead of passing a flow-handler
+	 * to gpiochip_set_chained_irqchip, because the irq is shared.
+	 */
+	ret = devm_request_irq(dev, irq, int0002_irq,
+			       IRQF_SHARED | IRQF_NO_THREAD, "INT0002", chip);
+	if (ret) {
+		dev_err(dev, "Error requesting IRQ %d: %d\n", irq, ret);
+		return ret;
+	}
+
+	ret = gpiochip_irqchip_add(chip, &int0002_irqchip, 0, handle_edge_irq,
+				   IRQ_TYPE_NONE);
+	if (ret) {
+		dev_err(dev, "Error adding irqchip: %d\n", ret);
+		return ret;
+	}
+
+	gpiochip_set_chained_irqchip(chip, &int0002_irqchip, irq, NULL);
+
+	return 0;
+}
+
+static const struct acpi_device_id int0002_acpi_ids[] = {
+	{ "INT0002", 0 },
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, int0002_acpi_ids);
+
+static struct platform_driver int0002_driver = {
+	.driver = {
+		.name			= DRV_NAME,
+		.acpi_match_table	= int0002_acpi_ids,
+	},
+	.probe	= int0002_probe,
+};
+
+module_platform_driver(int0002_driver);
+
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_DESCRIPTION("Intel INT0002 Virtual GPIO driver");
+MODULE_LICENSE("GPL");