From: "NG, TZE YEE" <tze.yee.ng@altera.com>
To: "Kathpalia, Tanmay" <tanmay.kathpalia@altera.com>,
Adrian Hunter <adrian.hunter@intel.com>,
linux-mmc@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
devicetree@vger.kernel.org, Ulf Hansson <ulfh@kernel.org>
Subject: Re: [PATCH v3 2/4] mmc: sdhci-cadence6: program PHONY_DQS_TIMING for extended-read DDR
Date: Tue, 17 Nov 2026 15:57:49 +0800 [thread overview]
Message-ID: <7879888a-b4cd-4c45-bb92-8db776f10d8d@altera.com> (raw)
In-Reply-To: <da0da5ca-164e-45cf-8921-598d67d6a42b@altera.com>
Hi Tanmay,
Thanks for the careful review, and sorry for the mixed signals between
the two threads.
On 15/11/2026 10:51 pm, Kathpalia, Tanmay wrote:
>
> On 06-11-2026 11:46, tze.yee.ng@altera.com wrote:
>> From: Tze Yee Ng <tze.yee.ng@altera.com>
>>
>> The SD6HC PHY left PHONY_DQS_TIMING (phy_ctrl_reg[9:4]) at 0 in all
>> modes. Per the Cadence DLL PHY documentation it must be the rebar (RE#)
>> pulse width in clk_phy cycles minus 1 in extended read mode, and 0
>> otherwise. Leaving it 0 in extended-read DDR duplicates one DDR edge
>> (the silent odd/even edge-capture defect).
>>
>> On this integration the rebar pulse is 2 clk_phy cycles, so extended-
>
> In the U-Boot thread you said this width is documented in the Cadence
> SD/eMMC DFI spec; in v1 here
> you said there is no IP-level document. Which is it? If documented,
> please cite it here and in the
> macro comment. If it is Agilex5-specific, please take it from the
> altr,agilex5-sd6hc match data
> instead of a constant for every cdns,sd6hc user.
>
You're right the threads were inconsistent. At v1 I had no IP-level
reference and used the characterised rebar width. While debugging the
U-Boot side I found the Cadence documents that actually describe this,
and I'll cite them from v4 on:
- COMBO DLL PHY User Guide (cdn_ip6182), phy_ctrl_reg (0x2080)
bits[9:4] phony_dqs_timing: 0 when extended_read_mode is disabled,
otherwise the rebar pulse width in clk_phy cycles minus 1 (its own
example: width 4 -> 3).
- SD/eMMC DFI Interface spec (cdn_ip6185) section 1.2.6.2, "DAT input
in extended clock mode" (Fig 1.23 DDR, Fig 1.26 SDR): the rebar
pulse spans half an SDCLK period.
So the rule is IP-documented; what I didn't have at v1 was the
reference, not a different rule.
>> read DDR needs 1; confirmed on DDR50 hardware (1 captures both beats, 2
>
> In v1 you confirmed DDR52 was validated too and said you would name both
> modes.
>
Yes, DDR52 is validated too. I'll name both DDR50 and DDR52 in the
commit message.
>> corrupts reads). Derive it from the extended-read-mode state and apply
>> it only in DDR modes, since SDR extended-read samples a single edge and
>> is unaffected.
>
> In v1 you agreed this is not proof ("Agreed the single-edge argument
> alone is not proof") and kept
> these modes at 0 because they pass there. On 5 Nov, in the U-Boot
> thread, you wrote the opposite
> rule: by the PHY guide the value "is 1 in extended-read mode and 0
> otherwise", and U-Boot v2 does
> set 1 for the divided SDR modes. This patch still leaves them at 0, so
> the two trees disagree. The
> PHY guide is not limited to DDR: 0 when extended read is off, and the
> rebar width minus 1 when it
> is on. With the rebar width of 2, that is 1 in every extended-read mode.
> Please program 1 in these
> modes here as well.
>
Combining the two docs: rebar width (in clk_phy cycles) = (SDCLK/2) /
clk_phy = divider/2, hence phony_dqs_timing = divider/2 - 1. The "2" in
v3 was just that evaluated at our clk_phy (~200 MHz -> divider 4 for
DDR50/DDR52).
Rather than hard-code a number that silently assumes Agilex5's clock, or
push it into the altr,agilex5-sd6hc match data, I'll derive it from the
clock ratio the driver already has (t_sdclk / t_sdmclk). That is correct
for any cdns,sd6hc instance and drops the magic constant, which also
removes the "this integration" vs "this controller" wording mismatch,
since there's no macro left to reconcile.
>>
>> Acked-by: Adrian Hunter <adrian.hunter@intel.com>
>> Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
>> ---
>> Changes in v3:
>> - No change; retains Adrian's Acked-by.
>>
>> Changes in v2:
>> - Added Adrian's Acked-by.
>> - Reworded the commit message to drop the "generic to any SD6HC-PHY SoC"
>> framing. (Adrian Hunter)
>> ---
>> drivers/mmc/host/sdhci-cadence-phy-v6.c | 15 +++++++++++++++
>> 1 file changed, 15 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci-cadence-phy-v6.c b/drivers/mmc/
>> host/sdhci-cadence-phy-v6.c
>> index 22d56bb46d75..8d6a9c26c139 100644
>> --- a/drivers/mmc/host/sdhci-cadence-phy-v6.c
>> +++ b/drivers/mmc/host/sdhci-cadence-phy-v6.c
>> @@ -90,6 +90,9 @@
>> #define SDHCI_CDNS6_PHY_CTRL_REG 0x2080
>> #define SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING
>> GENMASK(9, 4)
>> +/* Width of this controller's rebar (RE#) pulse in clk_phy cycles. */
>> +#define SDHCI_CDNS6_PHY_REBAR_PULSE_CYCLES 2
>> +
>
> The commit says "this integration", the comment says "this controller".
> Please make them match,
> with a source (see above).
>
See my reply above. This macro and comment will be removed.
>> /* Default PHY settings */
>> #define SDHCI_CDNS6_PHY_DEFAULT_IOCELL_DELAY 2500
>> #define SDHCI_CDNS6_PHY_DEFAULT_DELAY_ELEMENT 24
>> @@ -143,6 +146,9 @@ struct sdhci_cdns6_phy {
>> bool cp_use_phony_dqs; /* bit [20] */
>> bool cp_use_phony_dqs_cmd; /* bit [19] */
>> + /* PHY_CTRL register fields */
>> + u32 cp_phony_dqs_timing;
>> +
>
> u8 with /* bits [9:4] */, similar to the other cp_* fields.
>
Will change to u8 with a /* bits [9:4] */ comment, to match the other
cp_* fields.
>> /* HRS07 register - IO delay Information */
>> u8 sdhc_rw_compensate; /* bits [20:16] */
>> u8 sdhc_idelay_val; /* bits [4:0] */
>> @@ -517,6 +523,13 @@ static void sdhci_cdns6_phy_calc_dat_in(struct
>> sdhci_cdns6_phy *phy)
>> if (phy->mode == MMC_TIMING_MMC_HS200)
>> phy->cp_read_dqs_delay = phy->hs200_tune_val;
>> + if (phy->sdhc_extended_rd_mode &&
>> + (phy->mode == MMC_TIMING_UHS_DDR50 ||
>> + phy->mode == MMC_TIMING_MMC_DDR52))
>> + phy->cp_phony_dqs_timing = SDHCI_CDNS6_PHY_REBAR_PULSE_CYCLES
>> - 1;
>> + else
>> + phy->cp_phony_dqs_timing = 0;
>> +
>
> The PHY guide asks for width - 1 whenever extended read is on, which
> here also covers DS/HS/SDR
> modes. In U-Boot v2 you now do exactly that (1 in every extended-read
> mode), and said it matches
> the Linux change, but this patch keeps those modes at 0. It's confusing,
> I would suggest to follow
> the Cadence PHY user guide.
>
Agreed. The guide keys the field on extended_read_mode, not on DDR, and
U-Boot v2 already programs width-1 in every extended-read mode. The
computed form does exactly that: phony_dqs_timing = divider/2 - 1
whenever extended_read_mode is set, 0 otherwise. So the two trees will
agree.
>> if (strobe_dat) {
>> /* dqs loopback input via IO cell */
>> hcsdclkadj += phy->iocell_input_delay;
>> @@ -715,6 +728,8 @@ int sdhci_cdns6_phy_init(struct sdhci_cdns_priv
>> *priv)
>> reg = sdhci_cdns6_read_phy_reg(priv, SDHCI_CDNS6_PHY_CTRL_REG);
>> reg &= ~SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING;
>> + reg |= FIELD_PREP(SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING,
>> + phy->cp_phony_dqs_timing);
>
> This write always runs with the loopback DQS selected. The setting you
> tested was the phony DQS
> (use_lpbk_dqs = 0) and a read delay of 96. The PHY guide says this field
> times the phony strobe,
> so with loopback it may change nothing. Does this patch by itself fix
> the bad reads on the
> default loopback path? If not, please put it after patch 4, or merge it
> into patch 4.
Agreed it has no standalone effect. The loopback is force‑selected until
the opt‑in lands, so the write is muxed out. I'll fold the
PHONY_DQS_TIMING programming into patch 4, so the phony‑DQS opt‑in and
its correct timing land together and no commit can select phony DQS with
phony_dqs_timing = 0.
Thanks,
Tze Yee
next prev parent reply other threads:[~2026-11-17 7:58 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-06 6:16 [PATCH v3 0/4] mmc: sdhci-cadence: SD6HC DDR50/DDR52 read-path tuning and fixes tze.yee.ng
2026-11-06 6:16 ` [PATCH v3 1/4] mmc: sdhci-cadence: abort failed tuning command on SD6HC tze.yee.ng
2026-11-15 19:24 ` Kathpalia, Tanmay
[not found] ` <74458f24-9380-4c90-8f6e-6a6f345cc676@altera.com>
2026-11-16 7:59 ` NG, TZE YEE
2026-11-06 6:16 ` [PATCH v3 2/4] mmc: sdhci-cadence6: program PHONY_DQS_TIMING for extended-read DDR tze.yee.ng
2026-11-15 14:51 ` Kathpalia, Tanmay
2026-11-17 7:57 ` NG, TZE YEE [this message]
2026-11-06 6:16 ` [PATCH v3 3/4] dt-bindings: mmc: cdns,sd6hc: add SD6HC DDR50 read-path tuning tze.yee.ng
2026-11-06 12:40 ` Krzysztof Kozlowski
2026-11-06 6:16 ` [PATCH v3 4/4] mmc: sdhci-cadence6: read SD6HC DDR50 tuning from device tree tze.yee.ng
2026-11-15 18:47 ` Kathpalia, Tanmay
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7879888a-b4cd-4c45-bb92-8db776f10d8d@altera.com \
--to=tze.yee.ng@altera.com \
--cc=adrian.hunter@intel.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=robh@kernel.org \
--cc=tanmay.kathpalia@altera.com \
--cc=ulfh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®