From: Florian Fainelli <florian.fainelli@broadcom.com>
To: Wang Xiaolei <wangxiaolei01@kaihong.com>,
linusw@kernel.org, rjui@broadcom.com, sbranden@broadcom.com,
bcm-kernel-feedback-list@broadcom.com, daniel@dragonzap.com,
iivanov@suse.de, andrea.porta@suse.com, phil@raspberrypi.com
Cc: linux-gpio@vger.kernel.org, linux-rpi-kernel@lists.infradead.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org,
Jonathan Bell <jonathan@raspberrypi.com>
Subject: Re: [PATCH 1/3] pinctrl: bcm: Fix off-by-one and out-of-bounds access in fsel_get()
Date: Tue, 10 Nov 2026 09:46:55 -0800 [thread overview]
Message-ID: <79f827d9-8aec-49b4-bc70-117de314206e@broadcom.com> (raw)
In-Reply-To: <20261106070628.1428691-2-wangxiaolei01@kaihong.com>
On 11/5/26 23:06, Wang Xiaolei wrote:
> brcmstb_pinctrl_fsel_get() takes the value read from the pin's FSEL
> register and uses it directly as an index into
> pc->pin_funcs[pin].funcs[]:
>
> fsel = (val >> BIT_TO_SHIFT(bit)) & pc->pin_funcs[pin].func_mask;
> func = pc->pin_funcs[pin].funcs[fsel];
>
> That is not how the register field is encoded. The setter,
> brcmstb_pinctrl_fsel_set(), treats 0 as GPIO, 1..n_funcs as
> funcs[0..n_funcs - 1], rejects n_funcs + 1 and above, and n_funcs is
> always BRCMSTB_FSEL_COUNT (8). The field is therefore a 1-based function
> number, while funcs[] is a 0-based array of eight entries.
>
> Every readback is consequently shifted by one slot, and a field value of
> 8 -- which the setter accepts, being the eighth and last alternate
> function -- indexes funcs[8], one element past the end of the array.
>
> This is reachable from userspace without supplying any invalid input:
>
> # echo "gpio45 alt8" > .../pinmux-select
> # cat .../pins
>
> The write is an ordinary mux request that fsel_set() accepts; the read
> that follows goes through pinctrl_pins_show() ->
> brcmstb_pctl_pin_dbg_show() -> fsel_get() and triggers KASAN on
> Raspberry Pi 5:
>
> BUG: KASAN: global-out-of-bounds in brcmstb_pctl_pin_dbg_show
> Read of size 1 at addr ffffa07c577ab2e8 by task cat/839
> The buggy address belongs to the variable:
> __compound_literal.62+0x8/0x40
>
> A field value of 0 has the same root cause in a milder form: it is
> reported as funcs[0] instead of GPIO. The mux itself is programmed
> correctly in both cases, so this affects the debugfs readback and KASAN
> rather than the hardware configuration.
>
> Handle 0 and out-of-range values explicitly, and index funcs[] with
> fsel - 1, so that the getter uses the same numbering as the setter and
> the index can no longer go past funcs[n_funcs - 1]. The existing
> fallback for func__ placeholder entries is kept:
>
> if (!fsel)
> return pc->func_gpio;
>
> if (fsel > pc->pin_funcs[pin].n_funcs) {
> dev_warn(pc->dev,
> "invalid fsel %d for pin %u\n", fsel, pin);
> return pc->func_gpio;
> }
>
> func = pc->pin_funcs[pin].funcs[fsel - 1];
>
> Tested on Raspberry Pi 5 with KASAN enabled. Before the fix, writing
> "gpio45 alt8" to .../pinmux-select and then reading .../pins triggers
> the splat above. After the fix the same sequence reports
> "function spi_m" with no warning and no splat, and a register field
> value of 0 reports "gpio". The register is restored to 0 afterwards.
>
> Fixes: 657cbf9b24ba ("pinctrl: bcm: Add STB family pin controller driver")
> Cc: Jonathan Bell <jonathan@raspberrypi.com>
> Cc: Phil Elwell <phil@raspberrypi.com>
> Signed-off-by: Wang Xiaolei <wangxiaolei01@kaihong.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
--
Florian
next prev parent reply other threads:[~2026-11-10 17:47 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-06 7:06 [PATCH 0/3] pinctrl: bcm: Fix fsel_get() and use generic dt_free_map Wang Xiaolei
2026-11-06 7:06 ` [PATCH 1/3] pinctrl: bcm: Fix off-by-one and out-of-bounds access in fsel_get() Wang Xiaolei
2026-11-10 17:46 ` Florian Fainelli [this message]
2026-11-06 7:06 ` [PATCH 2/3] pinctrl: bcm: Use pinconf_generic_dt_free_map in bcm2835 Wang Xiaolei
2026-11-10 17:48 ` Florian Fainelli
2026-11-06 7:06 ` [PATCH 3/3] pinctrl: bcm: Use pinconf_generic_dt_free_map in brcmstb Wang Xiaolei
2026-11-10 17:49 ` Florian Fainelli
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=79f827d9-8aec-49b4-bc70-117de314206e@broadcom.com \
--to=florian.fainelli@broadcom.com \
--cc=andrea.porta@suse.com \
--cc=bcm-kernel-feedback-list@broadcom.com \
--cc=daniel@dragonzap.com \
--cc=iivanov@suse.de \
--cc=jonathan@raspberrypi.com \
--cc=linusw@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-rpi-kernel@lists.infradead.org \
--cc=phil@raspberrypi.com \
--cc=rjui@broadcom.com \
--cc=sbranden@broadcom.com \
--cc=wangxiaolei01@kaihong.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®