Re: [PATCH v14 05/10] drm/mediatek: Add MT8195 Embedded DisplayPort driver

[Rex-BC Chen <rex-bc.chen@mediatek.com>]

On Fri, 2022-07-15 at 16:51 +0800, CK Hu wrote:
> Hi, Bo-Chen:
> 
> On Tue, 2022-07-12 at 19:12 +0800, Bo-Chen Chen wrote:
> > From: Markus Schneider-Pargmann <msp@baylibre.com>
> > 
> > This patch adds a embedded displayport driver for the MediaTek
> > mt8195
> > SoC.
> > 
> > It supports the MT8195, the embedded DisplayPort units. It offers
> > DisplayPort 1.4 with up to 4 lanes.
> > 
> > The driver creates a child device for the phy. The child device
> > will
> > never exist without the parent being active. As they are sharing a
> > register range, the parent passes a regmap pointer to the child so
> > that
> > both can work with the same register range. The phy driver sets
> > device
> > data that is read by the parent to get the phy device that can be
> > used
> > to control the phy properties.
> > 
> > This driver is based on an initial version by
> > Jitao shi <jitao.shi@mediatek.com>
> > 
> > Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
> > Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
> > Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
> > ---
> 
> [snip]
> 
> > +static void mtk_dp_hpd_sink_event(struct mtk_dp *mtk_dp)
> > +{
> > +	ssize_t ret;
> > +	u8 sink_count;
> > +	u8 link_status[DP_LINK_STATUS_SIZE] = {};
> > +	u32 sink_count_reg = DP_SINK_COUNT_ESI;
> > +	u32 link_status_reg = DP_LANE0_1_STATUS;
> > +
> > +	ret = drm_dp_dpcd_readb(&mtk_dp->aux, sink_count_reg,
> > &sink_count);
> 
> According to your last reply, if drm_dp_dpcd_readb() fail, we could
> skip below statement. So this just for error checking? If so, the
> next
> drm_dp_dpcd_read() would also do the error checking, so the checking
> here is redundant.
> 
> Regards,
> CK
> 

Hello CK,

sorry, I don't get your point.
We use "drm_dp_dpcd_readb(&mtk_dp->aux, sink_count_reg, &sink_count)"
to get sink count and use "drm_dp_dpcd_read(&mtk_dp->aux,
link_status_reg, link_status, sizeof(link_status));" to get link
status.

If we don't get any sink count, we don't need to check the link status.
Therefore, we just return if we are failed to get sink count.

BRs,
Bo-Chen

> > +	if (ret < 1) {
> > +		drm_err(mtk_dp->drm_dev, "Read sink count failed\n");
> > +		return;
> > +	}
> > +
> > +	drm_dbg(mtk_dp->drm_dev,
> > +		"read sink count from dpcd: %d\n", sink_count);
> > +
> > +	ret = drm_dp_dpcd_read(&mtk_dp->aux, link_status_reg,
> > link_status,
> > +			       sizeof(link_status));
> > +	if (!ret) {
> > +		drm_err(mtk_dp->drm_dev, "Read link status failed\n");
> > +		return;
> > +	}
> > +
> > +	if (!drm_dp_channel_eq_ok(link_status, mtk_dp-
> > > train_info.lane_count)) {
> > 
> > +		drm_err(mtk_dp->drm_dev, "Channel EQ failed\n");
> > +		return;
> > +	}
> > +
> > +	if (link_status[1] & DP_REMOTE_CONTROL_COMMAND_PENDING)
> > +		drm_dp_dpcd_writeb(&mtk_dp->aux,
> > DP_DEVICE_SERVICE_IRQ_VECTOR,
> > +				   DP_REMOTE_CONTROL_COMMAND_PENDING);
> > +}
> > +
> 
>