From: Charan Pedumuru <charan.pedumuru@gmail.com>
To: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>,
Neil Armstrong <neil.armstrong@linaro.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Kishon Vijay Abraham I <kishon@kernel.org>,
Aaro Koskinen <aaro.koskinen@iki.fi>,
Andreas Kemnade <andreas@kemnade.info>,
Kevin Hilman <khilman@baylibre.com>,
Roger Quadros <rogerq@kernel.org>,
Tony Lindgren <tony@atomide.com>, Roger Quadros <rogerq@ti.com>,
linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-omap@vger.kernel.org
Subject: Re: [PATCH v3 2/3] dt-bindings: phy: ti,phy-usb3: convert to DT schema
Date: Fri, 23 Jan 2026 18:42:24 +0530 [thread overview]
Message-ID: <7b922a72-f17b-492f-ae04-a97a75738d4d@gmail.com> (raw)
In-Reply-To: <20260122233309.GA3730160-robh@kernel.org>
On 23-01-2026 05:03, Rob Herring wrote:
> On Thu, Jan 22, 2026 at 05:52:58PM +0000, Charan Pedumuru wrote:
>> Convert TI PIPE3 PHY binding to DT schema.
>> Changes during conversion:
>> - Define a new pattern 'pcie-phy' to match nodes defined in DT.
>> - Drop obsolete "id" property from the schema.
>>
>> Signed-off-by: Charan Pedumuru <charan.pedumuru@gmail.com>
>> ---
>> .../devicetree/bindings/phy/ti,phy-usb3.yaml | 135 +++++++++++++++++++++
>> 1 file changed, 135 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml b/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml
>> new file mode 100644
>> index 000000000000..605f12f0f79a
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/ti,phy-usb3.yaml
>> @@ -0,0 +1,135 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/phy/ti,phy-usb3.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: TI PIPE3 PHY Module
>> +
>> +maintainers:
>> + - Roger Quadros <rogerq@ti.com>
>> +
>> +description:
>> + The TI PIPE3 PHY is a high-speed SerDes (Serializer/Deserializer)
>> + transceiver integrated in OMAP5, DRA7xx/AM57xx, and similar SoCs.
>> + It supports multiple protocols (USB3, SATA, PCIe) using the PIPE3
>> + interface standard, which defines a common physical layer for
>> + high-speed serial interfaces.
>> +
>> +properties:
>> + $nodename:
>> + pattern: "^(pcie-phy|usb3-phy|phy)@[0-9a-f]+$"
>> +
>> + compatible:
>> + enum:
>> + - ti,omap-usb3
>> + - ti,phy-pipe3-pcie
>> + - ti,phy-pipe3-sata
>> + - ti,phy-usb3
>> +
>> + reg:
>> + minItems: 2
>> + maxItems: 3
>> +
>> + reg-names:
>> + minItems: 2
>> + items:
>> + - const: phy_rx
>> + - const: phy_tx
>> + - const: pll_ctrl
>> +
>> + "#phy-cells":
>> + const: 0
>> +
>> + clocks:
>> + minItems: 2
>> + maxItems: 7
>> +
>> + clock-names:
>> + minItems: 2
>> + maxItems: 7
>> + items:
>> + enum: [wkupclk, sysclk, refclk, dpll_ref,
>> + dpll_ref_m2, phy-div, div-clk]
>> +
>> + syscon-phy-power:
>> + $ref: /schemas/types.yaml#/definitions/phandle-array
>> + items:
>> + items:
>> + - description: Phandle to the system control module
>> + - description: Register offset controlling PHY power
>
> This allows N entries of 2 cells each. You need either:
>
> items:
> - items:
> - description: ...
> - description: ...
>
> (the hyphen is important!)
>
> Or:
>
> maxItems: 1
> items:
> items:
> - description: ...
> - description: ...
Okay, I will use the above format in the next revision.
>
>> +
>> + syscon-pllreset:
>> + $ref: /schemas/types.yaml#/definitions/phandle-array
>> + items:
>> + items:
>> + - description: Phandle to the system control module
>> + - description: Register offset of CTRL_CORE_SMA_SW_0
>> +
>> + syscon-pcs:
>> + $ref: /schemas/types.yaml#/definitions/phandle-array
>> + items:
>> + items:
>> + - description: Phandle to the system control module
>> + - description: Register offset for PCS delay programming
>> +
>> + ctrl-module:
>> + $ref: /schemas/types.yaml#/definitions/phandle
>> + description:
>> + Phandle of control module for PHY power on.
>> + deprecated: true
>> +
>> +allOf:
>> + - if:
>> + properties:
>> + compatible:
>> + contains:
>> + const: ti,phy-pipe3-sata
>> + then:
>> + properties:
>> + syscon-pllreset: true
>> + else:
>> + properties:
>> + syscon-pllreset: false
>> +
>> +required:
>> + - reg
>> + - compatible
>> + - reg-names
>> + - "#phy-cells"
>> + - clocks
>> + - clock-names
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + /* TI PIPE3 USB3 PHY */
>> + usb3-phy@4a084400 {
>> + compatible = "ti,phy-usb3";
>> + reg = <0x4a084400 0x80>,
>> + <0x4a084800 0x64>,
>> + <0x4a084c00 0x40>;
>> + reg-names = "phy_rx", "phy_tx", "pll_ctrl";
>> + #phy-cells = <0>;
>> + clocks = <&usb_phy_cm_clk32k>,
>> + <&sys_clkin>,
>> + <&usb_otg_ss_refclk960m>;
>> + clock-names = "wkupclk", "sysclk", "refclk";
>> + ctrl-module = <&omap_control_usb>;
>> + };
>> +
>> + - |
>> + /* TI PIPE3 SATA PHY */
>> + phy@4a096000 {
>> + compatible = "ti,phy-pipe3-sata";
>> + reg = <0x4A096000 0x80>, /* phy_rx */
>> + <0x4A096400 0x64>, /* phy_tx */
>> + <0x4A096800 0x40>; /* pll_ctrl */
>
> Use lowercase hex.
Sure.
>
>> + reg-names = "phy_rx", "phy_tx", "pll_ctrl";
>> + clocks = <&sys_clkin1>, <&sata_ref_clk>;
>> + clock-names = "sysclk", "refclk";
>> + syscon-pllreset = <&scm_conf 0x3fc>;
>> + #phy-cells = <0>;
>> + };
>> +...
>>
>> --
>> 2.52.0
>>
--
Best Regards,
Charan.
next prev parent reply other threads:[~2026-01-23 13:12 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-01-22 17:52 [PATCH v3 0/3] dt-bindings: phy: Convert TI OMAP control and PIPE3 PHY " Charan Pedumuru
2026-01-22 17:52 ` [PATCH v3 1/3] arm: dts: ti: omap: align node patterns with established convention Charan Pedumuru
2026-01-22 17:52 ` [PATCH v3 2/3] dt-bindings: phy: ti,phy-usb3: convert to DT schema Charan Pedumuru
2026-01-22 23:33 ` Rob Herring
2026-01-23 13:12 ` Charan Pedumuru [this message]
2026-01-22 17:52 ` [PATCH v3 3/3] dt-bindings: phy: ti,control-phy-otghs: " Charan Pedumuru
2026-01-22 23:34 ` Rob Herring (Arm)
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=7b922a72-f17b-492f-ae04-a97a75738d4d@gmail.com \
--to=charan.pedumuru@gmail.com \
--cc=aaro.koskinen@iki.fi \
--cc=andreas@kemnade.info \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=kishon@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=neil.armstrong@linaro.org \
--cc=robh@kernel.org \
--cc=rogerq@kernel.org \
--cc=rogerq@ti.com \
--cc=tony@atomide.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®