Re: [PATCH v2 2/4] dt-bindings: pinctrl: Document nuvoton ma35d1 pin control

[Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>]

On 28/11/2023 07:11, Jacky Huang wrote:
> From: Jacky Huang <ychuang3@nuvoton.com>
> 
> Add documentation to describe nuvoton ma35d1 pin control and GPIO.
> 
> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com>
> ---

Your changelog said:

>   - Remove ma35d1-pinfunc.h which is unused after update definition of
'nuvoton,pins'.

You forgot to add:

" - Do not test the bindings before sending"

I assume none of the driver changes compile either.

>  .../pinctrl/nuvoton,ma35d1-pinctrl.yaml       | 189 ++++++++++++++++++
>  1 file changed, 189 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
> new file mode 100644
> index 000000000000..84287293a726
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nuvoton,ma35d1-pinctrl.yaml
> @@ -0,0 +1,189 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/nuvoton,ma35d1-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Nuvoton MA35D1 pin control and GPIO
> +
> +maintainers:
> +  - Shan-Chun Hung <schung@nuvoton.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - nuvoton,ma35d1-pinctrl
> +
> +  '#address-cells':
> +    const: 1
> +
> +  '#size-cells':
> +    const: 1
> +
> +  nuvoton,sys:
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +    description:
> +      phandle of the system-management node.
> +
> +  ranges: true
> +
> +allOf:
> +  - $ref: pinctrl.yaml#

allOf goes before additionalProperties.

> +
> +required:
> +  - compatible
> +  - nuvoton,sys

This goes after patternProperties

> +
> +patternProperties:
> +  "^gpio@[0-9a-f]+$":
> +    type: object
> +    additionalProperties: false
> +    properties:
> +      gpio-controller: true
> +
> +      '#gpio-cells':
> +        const: 2
> +
> +      reg:
> +        maxItems: 1
> +
> +      clocks:
> +        maxItems: 1
> +
> +      interrupt-controller: true
> +
> +      '#interrupt-cells':
> +        const: 2
> +
> +      interrupts:
> +        description:
> +          The interrupt outputs to sysirq.
> +        maxItems: 1
> +
> +    required:
> +      - gpio-controller
> +      - '#gpio-cells'
> +      - reg
> +      - clocks
> +      - interrupt-controller
> +      - '#interrupt-cells'
> +      - interrupts
> +
> +  "^pin-[a-z0-9]+$":
> +    type: object
> +    description:
> +      A pinctrl node should contain at least one subnodes representing the
> +      pinctrl groups available on the machine. Each subnode will list the
> +      pins it needs, and how they should be configured, with regard to muxer
> +      configuration, pullups, drive strength, input enable/disable and input
> +      schmitt.
> +
> +    allOf:

Drop allOf, just $ref

> +      - $ref: pincfg-node.yaml#
> +
> +    properties:
> +      bias-disable: true

Drop this and other "true", why do you need them here?

> +
> +      bias-pull-down: true
> +
> +      bias-pull-up: true
> +
> +      power-source:
> +        description: |
> +          Valid arguments are described as below:
> +          0: power supply of 1.8V
> +          1: power supply of 3.3V
> +        enum: [0, 1]
> +
> +      drive-strength-microamp:
> +        oneOf:
> +          - enum: [ 2900, 4400, 5800, 7300, 8600, 10100, 11500, 13000 ]
> +            description: 1.8V I/O driving strength
> +          - enum: [ 17100, 25600, 34100, 42800, 48000, 56000, 77000, 82000 ]
> +            description: 3.3V I/O driving strength
> +
> +      input-enable: true
> +
> +      input-schmitt-enable: true
> +
> +    unevaluatedProperties: false



Best regards,
Krzysztof