mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Rishikesh Donadkar <r-donadkar@ti.com>
To: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>,
	<jai.luthra@linux.dev>, <laurent.pinchart@ideasonboard.com>,
	<mripard@kernel.org>
Cc: <y-abhilashchandra@ti.com>, <devarsht@ti.com>, <s-jain1@ti.com>,
	<vigneshr@ti.com>, <mchehab@kernel.org>, <robh@kernel.org>,
	<krzk+dt@kernel.org>, <p.zabel@pengutronix.de>,
	<conor+dt@kernel.org>, <sakari.ailus@linux.intel.com>,
	<hverkuil-cisco@xs4all.nl>, <jai.luthra@ideasonboard.com>,
	<changhuang.liang@starfivetech.com>, <jack.zhu@starfivetech.com>,
	<sjoerd@collabora.com>, <dan.carpenter@linaro.org>,
	<hverkuil+cisco@kernel.org>, <linux-kernel@vger.kernel.org>,
	<linux-media@vger.kernel.org>, <devicetree@vger.kernel.org>
Subject: Re: [PATCH v10 13/18] media: ti: j721e-csi2rx: add multistream support
Date: Fri, 30 Jan 2026 09:39:50 +0530	[thread overview]
Message-ID: <816bfa6a-c4ed-4389-b94f-2a5e5c2c0267@ti.com> (raw)
In-Reply-To: <ec8be3fb-b2c0-46bc-a2d7-aaeadb0bba37@ideasonboard.com>


On 23/01/26 14:56, Tomi Valkeinen wrote:
> Hi,
Hi Tomi,
>
> On 21/01/2026 15:54, Rishikesh Donadkar wrote:
>> From: Jai Luthra <j-luthra@ti.com>
>>
>> Each CSI2 stream can be multiplexed into 32 independent streams, each
>> identified by its virtual channel number and data type. The incoming
>> data from these streams can be filtered on the basis of either the
>> virtual channel or the data type.
>>
>> To capture this multiplexed stream, the application needs to tell
>> the driver how it wants to route the data. It needs to specify
>> which context should process which stream. This is done via the
>> new routing APIs.
>>
>> Add ioctls to accept routing information from the application and save
>> that in the driver. This can be used when starting streaming on a
>> context to determine which route and consequently which virtual channel
>> it should process.
>>
>> De-assert the pixel interface reset on first start_streaming() and assert
>> it on the last stop_streaming().
>>
>> Reviewed-by: Yemike Abhilash Chandra <y-abhilashchandra@ti.com>
>> Co-developed-by: Pratyush Yadav <p.yadav@ti.com>
>> Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
>> Signed-off-by: Jai Luthra <j-luthra@ti.com>
>> Co-developed-by: Rishikesh Donadkar <r-donadkar@ti.com>
>> Signed-off-by: Rishikesh Donadkar <r-donadkar@ti.com>
>> ---
>>   .../platform/ti/j721e-csi2rx/j721e-csi2rx.c   | 271 ++++++++++++------
>>   1 file changed, 191 insertions(+), 80 deletions(-)
>>
>> diff --git a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c
>> index 81c86e2cc4a50..4dabb99792d44 100644
>> --- a/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c
>> +++ b/drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c
>> @@ -143,17 +143,6 @@ static inline struct ti_csi2rx_dev *to_csi2rx_dev(struct v4l2_subdev *sd)
>>   	return container_of(sd, struct ti_csi2rx_dev, subdev);
>>   }
>>   
>> -static const struct v4l2_mbus_framefmt ti_csi2rx_default_fmt = {
>> -	.width = 640,
>> -	.height = 480,
>> -	.code = MEDIA_BUS_FMT_UYVY8_1X16,
>> -	.field = V4L2_FIELD_NONE,
>> -	.colorspace = V4L2_COLORSPACE_SRGB,
>> -	.ycbcr_enc = V4L2_YCBCR_ENC_601,
>> -	.quantization = V4L2_QUANTIZATION_LIM_RANGE,
>> -	.xfer_func = V4L2_XFER_FUNC_SRGB,
>> -};
>> -
>>   static const struct ti_csi2rx_fmt ti_csi2rx_formats[] = {
>>   	{
>>   		.fourcc			= V4L2_PIX_FMT_YUYV,
>> @@ -565,10 +554,6 @@ static void ti_csi2rx_setup_shim(struct ti_csi2rx_ctx *ctx)
>>   
>>   	fmt = find_format_by_fourcc(ctx->v_fmt.fmt.pix.pixelformat);
>>   
>> -	/* De-assert the pixel interface reset. */
>> -	reg = SHIM_CNTL_PIX_RST;
>> -	writel(reg, csi->shim + SHIM_CNTL);
>> -
>>   	/* Negotiate pixel count from the source */
>>   	ti_csi2rx_request_max_ppc(csi);
>>   
>> @@ -888,34 +873,75 @@ static void ti_csi2rx_buffer_queue(struct vb2_buffer *vb)
>>   	}
>>   }
>>   
>> +static int ti_csi2rx_get_stream(struct ti_csi2rx_ctx *ctx)
>> +{
>> +	struct ti_csi2rx_dev *csi = ctx->csi;
>> +	struct media_pad *pad;
>> +	struct v4l2_subdev_state *state;
>> +	struct v4l2_subdev_route *r;
>> +
>> +	/* Get the source pad connected to this ctx */
>> +	pad = media_entity_remote_source_pad_unique(ctx->pad.entity);
>> +	if (!pad) {
>> +		dev_err(csi->dev, "No pad connected to ctx %d\n", ctx->idx);
>> +		return -ENODEV;
>> +	}
>> +
>> +	state = v4l2_subdev_get_locked_active_state(&csi->subdev);
>> +
>> +	for_each_active_route(&state->routing, r) {
>> +		if (r->source_pad == pad->index) {
>> +			ctx->stream = r->sink_stream;
>> +			return 0;
>> +		}
>> +	}
>> +
>> +	/* No route found for this ctx */
>> +	return -ENODEV;
>> +}
>> +
>>   static int ti_csi2rx_get_vc_and_dt(struct ti_csi2rx_ctx *ctx)
>>   {
>>   	struct ti_csi2rx_dev *csi = ctx->csi;
>> +	struct ti_csi2rx_ctx *curr_ctx;
>>   	struct v4l2_mbus_frame_desc fd;
>> -	struct media_pad *pad;
>> -	int ret, i;
>> +	struct media_pad *source_pad;
>> +	int ret;
>> +	unsigned int i, j;
>>   
>> -	pad = media_entity_remote_pad_unique(&csi->subdev.entity, MEDIA_PAD_FL_SOURCE);
>> -	if (!pad)
>> +	/* Get the frame desc form source */
> "from".


Will correct

>
>> +	source_pad = media_entity_remote_pad_unique(&csi->subdev.entity, MEDIA_PAD_FL_SOURCE);
>> +	if (!source_pad)
>>   		return -ENODEV;
>>   
>> -	ret = v4l2_subdev_call(csi->source, pad, get_frame_desc, pad->index, &fd);
>> +	ret = v4l2_subdev_call(csi->source, pad, get_frame_desc, source_pad->index, &fd);
>>   	if (ret)
>>   		return ret;
>>   
>>   	if (fd.type != V4L2_MBUS_FRAME_DESC_TYPE_CSI2)
>>   		return -EINVAL;
>>   
>> -	for (i = 0; i < fd.num_entries; i++) {
>> -		if (ctx->stream == fd.entry[i].stream) {
>> -			ctx->vc = fd.entry[i].bus.csi2.vc;
>> -			ctx->dt = fd.entry[i].bus.csi2.dt;
>> -			break;
>> -		}
>> +	for (i = 0; i < csi->num_ctx; i++) {
>> +		curr_ctx = &csi->ctx[i];
>>   
>> -		/* Return error if no matching stream found */
>> -		if (i == fd.num_entries)
>> -			return -EINVAL;
>> +		/* Capture VC 0 by default */
>> +		curr_ctx->vc = 0;
>> +
>> +		ret = ti_csi2rx_get_stream(curr_ctx);
>> +		if (ret)
>> +			continue;
>> +
>> +		for (j = 0; j < fd.num_entries; j++) {
>> +			if (curr_ctx->stream == fd.entry[j].stream) {
>> +				curr_ctx->vc = fd.entry[j].bus.csi2.vc;
>> +				curr_ctx->dt = fd.entry[j].bus.csi2.dt;
>> +				break;
>> +			}
>> +
>> +			/* Return error if no matching stream found */
>> +			if (j == fd.num_entries)
>> +				return -EINVAL;
>> +		}
>>   	}
>>   
>>   	return 0;
>> @@ -926,8 +952,6 @@ static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count)
>>   	struct ti_csi2rx_ctx *ctx = vb2_get_drv_priv(vq);
>>   	struct ti_csi2rx_dev *csi = ctx->csi;
>>   	struct ti_csi2rx_dma *dma = &ctx->dma;
>> -	struct ti_csi2rx_buffer *buf;
>> -	const struct ti_csi2rx_fmt *fmt;
>>   	unsigned long flags;
>>   	int ret = 0;
>>   
>> @@ -942,35 +966,9 @@ static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count)
>>   	if (ret)
>>   		goto err;
>>   
>> -	ret = ti_csi2rx_get_vc_and_dt(ctx);
>> -	if (ret == -ENOIOCTLCMD) {
>> -		ctx->vc = 0;
>> -		fmt = find_format_by_fourcc(ctx->v_fmt.fmt.pix.pixelformat);
>> -		ctx->dt = fmt->csi_dt;
>> -	} else if (ret < 0) {
>> -		goto err;
>> -	}
>> -
>> -	ti_csi2rx_setup_shim(ctx);
>> -
>> -	ctx->sequence = 0;
>> -
>> -	spin_lock_irqsave(&dma->lock, flags);
>> -	buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list);
>> -
>> -	ret = ti_csi2rx_start_dma(ctx, buf);
>> -	if (ret) {
>> -		dev_err(csi->dev, "Failed to start DMA: %d\n", ret);
>> -		spin_unlock_irqrestore(&dma->lock, flags);
>> -		goto err_pipeline;
>> -	}
>> -
>> -	list_move_tail(&buf->list, &dma->submitted);
>> -	dma->state = TI_CSI2RX_DMA_ACTIVE;
>> -	spin_unlock_irqrestore(&dma->lock, flags);
>> -
>> +	/* Start stream 0, we don't allow multiple streams on the source pad */
>>   	ret = v4l2_subdev_enable_streams(&csi->subdev,
>> -					 TI_CSI2RX_PAD_FIRST_SOURCE,
>> +					 TI_CSI2RX_PAD_FIRST_SOURCE + ctx->idx,
>>   					 BIT_U64(0));
>>   	if (ret)
>>   		goto err_dma;
>> @@ -979,7 +977,6 @@ static int ti_csi2rx_start_streaming(struct vb2_queue *vq, unsigned int count)
>>   
>>   err_dma:
>>   	ti_csi2rx_stop_dma(ctx);
>> -err_pipeline:
>>   	video_device_pipeline_stop(&ctx->vdev);
>>   	writel(0, csi->shim + SHIM_CNTL);
>>   	writel(0, csi->shim + SHIM_DMACNTX(ctx->idx));
>> @@ -996,11 +993,8 @@ static void ti_csi2rx_stop_streaming(struct vb2_queue *vq)
>>   
>>   	video_device_pipeline_stop(&ctx->vdev);
>>   
>> -	writel(0, csi->shim + SHIM_CNTL);
>> -	writel(0, csi->shim + SHIM_DMACNTX(ctx->idx));
>> -
>>   	ret = v4l2_subdev_disable_streams(&csi->subdev,
>> -					  TI_CSI2RX_PAD_FIRST_SOURCE,
>> +					  TI_CSI2RX_PAD_FIRST_SOURCE + ctx->idx,
>>   					  BIT_U64(0));
>>   	if (ret)
>>   		dev_err(csi->dev, "Failed to stop subdev stream\n");
>> @@ -1047,25 +1041,84 @@ static int ti_csi2rx_sd_set_fmt(struct v4l2_subdev *sd,
>>   	fmt = v4l2_subdev_state_get_format(state, format->pad, format->stream);
>>   	*fmt = format->format;
>>   
>> -	fmt = v4l2_subdev_state_get_format(state, TI_CSI2RX_PAD_FIRST_SOURCE,
>> -					   format->stream);
>> +	fmt = v4l2_subdev_state_get_opposite_stream_format(state, format->pad,
>> +							   format->stream);
>> +	if (!fmt)
>> +		return -EINVAL;
>> +
>>   	*fmt = format->format;
>>   
>>   	return 0;
>>   }
>>   
>> -static int ti_csi2rx_sd_init_state(struct v4l2_subdev *sd,
>> -				   struct v4l2_subdev_state *state)
>> +static int _ti_csi2rx_sd_set_routing(struct v4l2_subdev *sd,
>> +				     struct v4l2_subdev_state *state,
>> +				     struct v4l2_subdev_krouting *routing)
>>   {
>> -	struct v4l2_mbus_framefmt *fmt;
>> +	int ret;
>>   
>> -	fmt = v4l2_subdev_state_get_format(state, TI_CSI2RX_PAD_SINK);
>> -	*fmt = ti_csi2rx_default_fmt;
>> +	static const struct v4l2_mbus_framefmt format = {
>> +		.width = 640,
>> +		.height = 480,
>> +		.code = MEDIA_BUS_FMT_UYVY8_1X16,
>> +		.field = V4L2_FIELD_NONE,
>> +		.colorspace = V4L2_COLORSPACE_SRGB,
>> +		.ycbcr_enc = V4L2_YCBCR_ENC_601,
>> +		.quantization = V4L2_QUANTIZATION_LIM_RANGE,
>> +		.xfer_func = V4L2_XFER_FUNC_SRGB,
>> +	};
>>   
>> -	fmt = v4l2_subdev_state_get_format(state, TI_CSI2RX_PAD_FIRST_SOURCE);
>> -	*fmt = ti_csi2rx_default_fmt;
>> +	ret = v4l2_subdev_routing_validate(sd, routing,
>> +					   V4L2_SUBDEV_ROUTING_ONLY_1_TO_1 |
>> +					   V4L2_SUBDEV_ROUTING_NO_SOURCE_MULTIPLEXING);
>>   
>> -	return 0;
>> +	if (ret)
>> +		return ret;
>> +
>> +	/* Only stream ID 0 allowed on source pads */
>> +	for (unsigned int i = 0; i < routing->num_routes; ++i) {
>> +		const struct v4l2_subdev_route *route = &routing->routes[i];
>> +
>> +		if (route->source_stream != 0)
>> +			return -EINVAL;
>> +	}
>> +
>> +	ret = v4l2_subdev_set_routing_with_fmt(sd, state, routing, &format);
>> +
>> +	return ret;
>> +}
>> +
>> +static int ti_csi2rx_sd_set_routing(struct v4l2_subdev *sd,
>> +				    struct v4l2_subdev_state *state,
>> +				    enum v4l2_subdev_format_whence which,
>> +				    struct v4l2_subdev_krouting *routing)
>> +{
>> +	struct ti_csi2rx_dev *csi = to_csi2rx_dev(sd);
>> +
>> +	if (csi->enable_count > 0)
>> +		return -EBUSY;
>> +
>> +	return _ti_csi2rx_sd_set_routing(sd, state, routing);
>> +}
>> +
>> +static int ti_csi2rx_sd_init_state(struct v4l2_subdev *sd,
>> +				   struct v4l2_subdev_state *state)
>> +{
>> +	struct v4l2_subdev_route routes[] = { {
>> +		.sink_pad = 0,
>> +		.sink_stream = 0,
>> +		.source_pad = TI_CSI2RX_PAD_FIRST_SOURCE,
>> +		.source_stream = 0,
>> +		.flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE,
>> +	} };
>> +
>> +	struct v4l2_subdev_krouting routing = {
>> +		.num_routes = 1,
>> +		.routes = routes,
>> +	};
>> +
>> +	/* Initialize routing to single route to the fist source pad */
>> +	return _ti_csi2rx_sd_set_routing(sd, state, &routing);
>>   }
>>   
>>   static int ti_csi2rx_sd_enable_streams(struct v4l2_subdev *sd,
>> @@ -1073,15 +1126,62 @@ static int ti_csi2rx_sd_enable_streams(struct v4l2_subdev *sd,
>>   				       u32 pad, u64 streams_mask)
>>   {
>>   	struct ti_csi2rx_dev *csi = to_csi2rx_dev(sd);
>> +	struct ti_csi2rx_ctx *ctx = &csi->ctx[pad - TI_CSI2RX_PAD_FIRST_SOURCE];
>> +	struct ti_csi2rx_dma *dma = &ctx->dma;
>>   	struct media_pad *remote_pad;
>> +	struct ti_csi2rx_buffer *buf;
>> +	const struct ti_csi2rx_fmt *fmt;
>> +	unsigned long flags;
>> +	u64 sink_streams;
>>   	int ret = 0;
>> +	unsigned int reg;
>> +
>> +	ret = ti_csi2rx_get_stream(ctx);
>> +	if (ret)
>> +		return ret;
>> +
>> +	/* Get the VC and DT for all enabled ctx on first stream start */
>> +	if (!csi->enable_count) {
>> +		ret = ti_csi2rx_get_vc_and_dt(ctx);
>> +		if (ret == -ENOIOCTLCMD) {
>> +			ctx->vc = 0;
>> +			fmt = find_format_by_fourcc(ctx->v_fmt.fmt.pix.pixelformat);
>> +			ctx->dt = fmt->csi_dt;
> I think the above lines would well fit into the
> ti_csi2rx_get_vc_and_dt() function.


Okay, will do that.

Rishikesh

>
> Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
>
>   Tomi
>
>> +		} else if (ret < 0) {
>> +			return ret;
>> +		}
>> +
>> +		/* De-assert the pixel interface reset. */
>> +		reg = SHIM_CNTL_PIX_RST;
>> +		writel(reg, csi->shim + SHIM_CNTL);
>> +	}
>> +
>> +	ti_csi2rx_setup_shim(ctx);
>> +	ctx->sequence = 0;
>> +
>> +	spin_lock_irqsave(&dma->lock, flags);
>> +	buf = list_entry(dma->queue.next, struct ti_csi2rx_buffer, list);
>> +
>> +	ret = ti_csi2rx_start_dma(ctx, buf);
>> +	if (ret) {
>> +		dev_err(csi->dev, "Failed to start DMA: %d\n", ret);
>> +		spin_unlock_irqrestore(&dma->lock, flags);
>> +		return ret;
>> +	}
>> +
>> +	list_move_tail(&buf->list, &dma->submitted);
>> +	dma->state = TI_CSI2RX_DMA_ACTIVE;
>> +	spin_unlock_irqrestore(&dma->lock, flags);
>>   
>>   	remote_pad = media_entity_remote_source_pad_unique(&csi->subdev.entity);
>>   	if (!remote_pad)
>>   		return -ENODEV;
>> +	sink_streams = v4l2_subdev_state_xlate_streams(state, pad,
>> +						       TI_CSI2RX_PAD_SINK,
>> +						       &streams_mask);
>>   
>>   	ret = v4l2_subdev_enable_streams(csi->source, remote_pad->index,
>> -					 BIT_U64(0));
>> +					 sink_streams);
>>   	if (ret)
>>   		return ret;
>>   
>> @@ -1095,18 +1195,28 @@ static int ti_csi2rx_sd_disable_streams(struct v4l2_subdev *sd,
>>   					u32 pad, u64 streams_mask)
>>   {
>>   	struct ti_csi2rx_dev *csi = to_csi2rx_dev(sd);
>> +	struct ti_csi2rx_ctx *ctx = &csi->ctx[pad - TI_CSI2RX_PAD_FIRST_SOURCE];
>>   	struct media_pad *remote_pad;
>> +	u64 sink_streams;
>>   	int ret = 0;
>>   
>> +	WARN_ON(csi->enable_count == 0);
>> +
>> +	writel(0, csi->shim + SHIM_DMACNTX(ctx->idx));
>> +
>> +	/* assert pixel reset to prevent stale data */
>> +	if (csi->enable_count == 1)
>> +		writel(0, csi->shim + SHIM_CNTL);
>> +
>>   	remote_pad = media_entity_remote_source_pad_unique(&csi->subdev.entity);
>>   	if (!remote_pad)
>>   		return -ENODEV;
>> -
>> -	if (csi->enable_count == 0)
>> -		return -EINVAL;
>> +	sink_streams = v4l2_subdev_state_xlate_streams(state, pad,
>> +						       TI_CSI2RX_PAD_SINK,
>> +						       &streams_mask);
>>   
>>   	ret = v4l2_subdev_disable_streams(csi->source, remote_pad->index,
>> -					  BIT_U64(0));
>> +					  sink_streams);
>>   	if (!ret)
>>   		--csi->enable_count;
>>   
>> @@ -1115,6 +1225,7 @@ static int ti_csi2rx_sd_disable_streams(struct v4l2_subdev *sd,
>>   
>>   static const struct v4l2_subdev_pad_ops ti_csi2rx_subdev_pad_ops = {
>>   	.enum_mbus_code	= ti_csi2rx_enum_mbus_code,
>> +	.set_routing = ti_csi2rx_sd_set_routing,
>>   	.get_fmt = v4l2_subdev_get_fmt,
>>   	.set_fmt = ti_csi2rx_sd_set_fmt,
>>   	.enable_streams = ti_csi2rx_sd_enable_streams,
>> @@ -1293,7 +1404,7 @@ static int ti_csi2rx_v4l2_init(struct ti_csi2rx_dev *csi)
>>   	v4l2_subdev_init(sd, &ti_csi2rx_subdev_ops);
>>   	sd->internal_ops = &ti_csi2rx_internal_ops;
>>   	sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
>> -	sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
>> +	sd->flags = V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_STREAMS;
>>   	strscpy(sd->name, dev_name(csi->dev), sizeof(sd->name));
>>   	sd->dev = csi->dev;
>>   	sd->entity.ops = &ti_csi2rx_subdev_entity_ops;
>

  reply	other threads:[~2026-01-30  4:10 UTC|newest]

Thread overview: 28+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-01-21 13:54 [PATCH v10 00/18] media: cadence,ti: CSI2RX Multistream Support Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 01/18] media: ti: j721e-csi2rx: Remove word size alignment on frame width Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 02/18] dt-bindings: media: ti,j721e-csi2rx-shim: Support 32 dma chans Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 03/18] media: ti: j721e-csi2rx: separate out device and context Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 04/18] media: ti: j721e-csi2rx: prepare SHIM code for multiple contexts Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 05/18] media: ti: j721e-csi2rx: allocate DMA channel based on context index Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 06/18] media: ti: j721e-csi2rx: add a subdev for the core device Rishikesh Donadkar
2026-01-23  8:40   ` Tomi Valkeinen
2026-01-21 13:54 ` [PATCH v10 07/18] media: cadence: csi2rx: Move to .enable/disable_streams API Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 08/18] media: ti: j721e-csi2rx: get number of contexts from device tree Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 09/18] media: cadence: csi2rx: add get_frame_desc wrapper Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 10/18] media: ti: j721e-csi2rx: add support for processing virtual channels Rishikesh Donadkar
2026-01-23  8:50   ` Tomi Valkeinen
2026-01-30  4:00     ` Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 11/18] media: cadence: csi2rx: add multistream support Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 12/18] media: cadence: csi2rx: Use the stream from route to get format Rishikesh Donadkar
2026-01-23  7:53   ` Tomi Valkeinen
2026-01-30  4:07     ` Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 13/18] media: ti: j721e-csi2rx: add multistream support Rishikesh Donadkar
2026-01-23  9:26   ` Tomi Valkeinen
2026-01-30  4:09     ` Rishikesh Donadkar [this message]
2026-01-21 13:54 ` [PATCH v10 14/18] media: ti: j721e-csi2rx: Submit all available buffers Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 15/18] media: ti: j721e-csi2rx: Change the drain architecture for multistream Rishikesh Donadkar
2026-01-23  9:29   ` Tomi Valkeinen
2026-01-21 13:54 ` [PATCH v10 16/18] media: cadence: csi2rx: Support runtime PM Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 17/18] media: ti: j721e-csi2rx: Support runtime suspend Rishikesh Donadkar
2026-01-21 13:54 ` [PATCH v10 18/18] media: ti: j721e-csi2rx: Support system suspend using pm_notifier Rishikesh Donadkar
2026-01-23  9:33   ` Tomi Valkeinen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=816bfa6a-c4ed-4389-b94f-2a5e5c2c0267@ti.com \
    --to=r-donadkar@ti.com \
    --cc=changhuang.liang@starfivetech.com \
    --cc=conor+dt@kernel.org \
    --cc=dan.carpenter@linaro.org \
    --cc=devarsht@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=hverkuil+cisco@kernel.org \
    --cc=hverkuil-cisco@xs4all.nl \
    --cc=jack.zhu@starfivetech.com \
    --cc=jai.luthra@ideasonboard.com \
    --cc=jai.luthra@linux.dev \
    --cc=krzk+dt@kernel.org \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=mripard@kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh@kernel.org \
    --cc=s-jain1@ti.com \
    --cc=sakari.ailus@linux.intel.com \
    --cc=sjoerd@collabora.com \
    --cc=tomi.valkeinen@ideasonboard.com \
    --cc=vigneshr@ti.com \
    --cc=y-abhilashchandra@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®