Re: [PATCH 2/2] arm64: dts: ti: k3-j784s4-evm: Enable USB3 support

[Roger Quadros <rogerq@kernel.org>]

On 02/05/2024 08:36, Ravi Gunasekaran wrote:
> From: Matt Ranostay <mranostay@ti.com>
> 
> The board uses SERDES0 Lane 3 for USB3 IP. So update the
> SerDes lane info for USB. Add the pin mux data and
> enable USB3 support.
> 
> Signed-off-by: Matt Ranostay <mranostay@ti.com>
> Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 41 ++++++++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> index d511b25d62e3..bee73dab803d 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
> @@ -336,6 +336,13 @@
>  			J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
>  		>;
>  	};
> +
> +	main_usbss0_pins_default: main-usbss0-pins-default {

Should be main-usbss0-default-pins

This should fix the checkpatch warning.

> +		bootph-all;
> +		pinctrl-single,pins = <
> +			J784S4_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AN37) TIMER_IO1.USB0_DRVVBUS */
> +		>;
> +	};
>  };
>  
>  &wkup_pmx2 {
> @@ -1041,6 +1048,40 @@
>  				 <&k3_clks 218 22>;
>  };
>  
> +&serdes0 {
> +	status = "okay";
> +
> +	serdes0_usb_link: phy@3 {
> +		reg = <3>;
> +		cdns,num-lanes = <1>;
> +		#phy-cells = <0>;
> +		cdns,phy-type = <PHY_TYPE_USB3>;
> +		resets = <&serdes_wiz0 4>;
> +	};
> +};
> +
> +&serdes_wiz0 {
> +	status = "okay";
> +};
> +
> +&usb_serdes_mux {
> +	idle-states = <0>; /* USB0 to SERDES lane 3 */
> +};
> +
> +&usbss0 {
> +	status = "okay";
> +	pinctrl-0 = <&main_usbss0_pins_default>;
> +	pinctrl-names = "default";
> +	ti,vbus-divider;
> +};
> +
> +&usb0 {
> +	dr_mode = "otg";
> +	maximum-speed = "super-speed";
> +	phys = <&serdes0_usb_link>;
> +	phy-names = "cdns3,usb3-phy";
> +};
> +
>  &serdes_wiz4 {
>  	status = "okay";
>  };

-- 
cheers,
-roger