From: Yinghai Lu <yinghai@kernel.org>
To: Sarah Sharp <sarah.a.sharp@intel.com>, Greg KH <gregkh@suse.de>,
"Eric W. Biederman" <ebiederm@xmission.com>,
Ingo Molnar <mingo@elte.hu>
Cc: linux-usb@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>,
Andrew Morton <akpm@linux-foundation.org>
Subject: Re: EHCI debug documentation
Date: Tue, 3 Mar 2009 17:31:44 -0800 [thread overview]
Message-ID: <86802c440903031731x36c1180dk72a3631bb4397319@mail.gmail.com> (raw)
In-Reply-To: <20090303235354.GA7145@gamba.jf.intel.com>
On Tue, Mar 3, 2009 at 3:53 PM, Sarah Sharp <sarah.a.sharp@intel.com> wrote:
> Greetings,
>
> You wrote the EHCI debug port patch for early printk back in July 2008
> (commit 5c05917e7fe313a187ad6ebb94c1c6cf42862a0b). Can you add some
> documentation to the Documentation directory about how a Linux user
> would set up a system (cables, files to open to get the printks, etc.)?
please check
==========================================================================================
USB Debug port using Howto
1. HW:
a. target system need to have debug port
00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2
EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
Subsystem: Lenovo ThinkPad T61
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 19
Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00: 86 80 36 28 06 01 90 02 03 20 03 0c 00 00 00 00
10: 00 70 22 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 aa 17 ab 20
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 58 c2 c9 00 80 00 00 0a 00 a0 20 00 00 00 00
60: 20 20 9f 01 00 00 00 00 01 00 00 01 00 00 08 80
70: c0 00 17 3f 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 aa ff 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 88 85 40 00 86 0f 05 00 06 17 02 20
b. netchip USB debug cable
c. console system: have USB port
2. SW setting
a. console system: need to have kernel config
CONFIG_USB_SERIAL_DEBUG
you should get /dev/ttyUSBx
# cat /dev/ttyUSBx could get output
b. target system: need to have kernel config
CONFIG_EARLY_PRINTK_DBGP
boot command line: earlyprintk=dbgp
c. for Nvidia Southbridge based system: kernel will try to probe and
find out which port has debug device connected.
next parent reply other threads:[~2009-03-04 1:31 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20090303235354.GA7145@gamba.jf.intel.com>
2009-03-04 1:31 ` Yinghai Lu [this message]
2009-03-04 1:36 ` Randy Dunlap
2009-03-04 17:57 ` Ingo Molnar
2009-03-04 21:25 ` Greg KH
2009-03-04 21:39 ` Eric W. Biederman
2009-03-04 21:59 ` Alan Stern
2009-03-04 22:55 ` Sarah Sharp
2009-03-05 0:11 ` [PATCH] x86/doc: doc the using earlyprintk=dbgp Yinghai Lu
2009-03-05 10:00 ` [tip:x86/doc] x86/doc: mini-howto for " Yinghai Lu
2009-03-05 15:36 ` Daniel Walker
2009-03-05 19:22 ` Yinghai Lu
2009-03-05 22:40 ` Daniel Walker
2009-03-05 22:54 ` Alan Stern
2009-03-05 23:02 ` Daniel Walker
2009-03-05 23:05 ` Randy Dunlap
2009-03-05 23:12 ` Daniel Walker
2009-03-05 23:19 ` Randy Dunlap
2009-03-05 23:32 ` Daniel Walker
2009-03-05 23:41 ` Randy Dunlap
2009-03-05 23:44 ` Daniel Walker
2009-03-06 14:57 ` Alan Stern
2009-03-06 15:03 ` Daniel Walker
2009-03-06 15:55 ` Alan Stern
2009-03-05 23:48 ` Daniel Walker
2009-03-05 23:59 ` Randy Dunlap
2009-03-06 0:09 ` Daniel Walker
2009-03-06 15:52 ` Alan Stern
2009-03-06 15:55 ` Ingo Molnar
2009-03-06 16:16 ` Daniel Walker
2009-03-06 2:23 ` Daniel Walker
2009-03-05 2:06 ` EHCI debug documentation Greg KH
2009-03-04 22:50 ` Sarah Sharp
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=86802c440903031731x36c1180dk72a3631bb4397319@mail.gmail.com \
--to=yinghai@kernel.org \
--cc=akpm@linux-foundation.org \
--cc=ebiederm@xmission.com \
--cc=gregkh@suse.de \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mingo@elte.hu \
--cc=sarah.a.sharp@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®