From: Punit Agrawal <punit.agrawal@arm.com>
To: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-doc@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, steve.capper@arm.com,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will.deacon@arm.com>,
Jonathan Corbet <corbet@lwn.net>
Subject: Re: [PATCH] Documentation/arm64: HugeTLB page implementation
Date: Mon, 08 Oct 2018 10:39:10 +0100 [thread overview]
Message-ID: <871s90u69t.fsf@e105922-lin.cambridge.arm.com> (raw)
In-Reply-To: <97e4e5fb-24ed-0545-414a-6a0c0116e6b8@infradead.org> (Randy Dunlap's message of "Sat, 6 Oct 2018 09:30:19 -0700")
Hi Randy,
Randy Dunlap <rdunlap@infradead.org> writes:
> Hi,
> Just some minor stuff (below).
>
> On 10/5/18 7:34 AM, Punit Agrawal wrote:
>> Arm v8 architecture supports multiple page sizes - 4k, 16k and
>> 64k. Based on the active page size, the Linux port supports
>> corresponding hugepage sizes at PMD and PUD(4k only) levels.
>>
>> In addition, the architecture also supports caching larger sized
>> ranges (composed of multiple entries) at the PTE and PMD level in the
>> TLBs using the contiguous bit. The Linux port makes use of this
>> architectural support to enable additional hugepage sizes.
>>
>> Describe the two different types of hugepages supported by the arm64
>> kernel and the hugepage sizes enabled by each.
>>
>> Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
>> Cc: Catalin Marinas <catalin.marinas@arm.com>
>> Cc: Will Deacon <will.deacon@arm.com>
>> Cc: Jonathan Corbet <corbet@lwn.net>
>> ---
>> Documentation/arm64/hugetlbpage.txt | 39 +++++++++++++++++++++++++++++
>> 1 file changed, 39 insertions(+)
>> create mode 100644 Documentation/arm64/hugetlbpage.txt
>>
>> diff --git a/Documentation/arm64/hugetlbpage.txt b/Documentation/arm64/hugetlbpage.txt
>> new file mode 100644
>> index 000000000000..64ee24b88d27
>> --- /dev/null
>> +++ b/Documentation/arm64/hugetlbpage.txt
>> @@ -0,0 +1,39 @@
>> +HugeTLBpage on ARM64
>> +====================
>> +
>> +Hugepage relies on making efficient use of TLBs to improve performance of
>> +address translations. The benefit depends on both -
>> +
>> + - the size of hugepages
>> + - size of entries supported by the TLBs
>> +
>> +The ARM64 port supports two flavours of hugepages.
>> +
>> +1) Block mappings at the pud/pmd level
>> +--------------------------------------
>> +
>> +These are regular hugepages where a pmd or a pud page table entry points to a
>> +block of memory. Regardless of the supported size of entries in TLB, block
>> +mappings reduces the depth of page table walk needed to translate hugepage
>
> reduce
>
>> +addresses.
>> +
>> +2) Using the Contiguous bit
>> +---------------------------
>> +
>> +The architecture provides a contiguous bit in the translation table entries
>> +(D4.5.3, ARM DDI 0487C.a) that hints to the mmu to indicate that it is one of a
>
> preferably MMU
>
>> +contiguous set of entries that can be cached in a single TLB entry.
>> +
>> +The contiguous bit is used in Linux to increase the mapping size at the pmd and
>> +pte (last) level. The number of supported contiguous entries vary by page size
>
> varies
>
>> +and level of the page table.
>> +
>> +
>> +
>> +The following hugepage sizes are supported -
>> +
>> + CONT PTE PMD CONT PMD PUD
>> + -------- --- -------- ---
>> + 4K: 64K 2M 32M 1G
>> + 16K: 2M 32M 1G
>> + 64K: 2M 512M 16G
>>
I've updated the patch with incorporating your feedback and will post an
update shortly.
Thanks a lot for taking a look.
Punit
next prev parent reply other threads:[~2018-10-08 9:39 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-05 14:34 Punit Agrawal
2018-10-06 16:30 ` Randy Dunlap
2018-10-08 9:39 ` Punit Agrawal [this message]
2018-10-08 10:03 ` [PATCH v2] " Punit Agrawal
2018-10-08 19:49 ` Randy Dunlap
2018-10-09 10:02 ` Punit Agrawal
2018-10-09 11:50 ` Will Deacon
2018-10-10 17:08 ` Catalin Marinas
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=871s90u69t.fsf@e105922-lin.cambridge.arm.com \
--to=punit.agrawal@arm.com \
--cc=catalin.marinas@arm.com \
--cc=corbet@lwn.net \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-doc@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=rdunlap@infradead.org \
--cc=steve.capper@arm.com \
--cc=will.deacon@arm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®