From: Mathias Nyman <mathias.nyman@linux.intel.com>
To: Lu Baolu <baolu.lu@linux.intel.com>,
Peter Zijlstra <peterz@infradead.org>
Cc: x86@kernel.org, linux-kernel@vger.kernel.org,
gregkh@linuxfoundation.org, linux-usb@vger.kernel.org
Subject: Re: earlyprintk=xdbc seems broken
Date: Fri, 3 Dec 2021 16:31:42 +0200 [thread overview]
Message-ID: <88f466ff-a065-1e9a-4226-0abe2e71b686@linux.intel.com> (raw)
In-Reply-To: <105f35d2-3c53-b550-bfb4-aa340d31128e@linux.intel.com>
On 3.12.2021 2.52, Lu Baolu wrote:
> Hi Peter,
>
> On 12/2/21 11:22 PM, Peter Zijlstra wrote:
>> Hi Lu,
>>
>> I was unfortunate enough to need xdbc and can't get my machine to boot
>> with earlyprintk=xdbc on the cmdline.
>>
>> When I boot the target without the earlyprintk=xdbc, but have the cable
>> attached, it won't boot because boot gets stuck like:
>>
>> Dec 2 15:08:10 tigerlake kernel: [ 42.043137] usb usb4-port3: Cannot enable. Maybe the USB cable is bad?
>> Dec 2 15:08:10 tigerlake kernel: [ 42.043227] usb usb4-port3: config error
>>
>> However, when I boot without earlyprintk=xdbc, without the cable
>> attached, then I can attach the cable and:
>>
>> $ echo enable > /sys/bus/pci/devices/0000:00:14.0/dbc
>>
>> will actually work, and it shows up on my host system:
>>
>> [1023855.419430] usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
>> [1023855.419455] usb usb2-port3: config error
>> [1023859.491476] usb usb2-port3: Cannot enable. Maybe the USB cable is bad?
>> [1023859.491487] usb usb2-port3: config error
>> [1023861.335436] usb usb2-port3: config error
>> [1023861.607476] usb 2-3: new SuperSpeed USB device number 7 using xhci_hcd
>> [1023861.627614] usb 2-3: LPM exit latency is zeroed, disabling LPM.
>> [1023861.627853] usb 2-3: New USB device found, idVendor=1d6b, idProduct=0010, bcdDevice= 0.10
>> [1023861.627855] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
>> [1023861.627856] usb 2-3: Product: Linux USB Debug Target
>> [1023861.627857] usb 2-3: Manufacturer: Linux Foundation
>> [1023861.627858] usb 2-3: SerialNumber: 0001
>> [1023861.629344] usb_debug 2-3:1.0: xhci_dbc converter detected
>> [1023861.629532] usb 2-3: xhci_dbc converter now attached to ttyUSB0
>>
>>
>> Can you please see if you can repro and fix this?
>>
>> This all was with current 5.16-rc3 on a tigerlake nuc.
>>
>> Also, perhaps you can update the guide on what sort of setup/cables
>> etc.. you need when either the host or the client is a usb3.1 usb-c only
>> device.
>>
>
> + Mathias, maybe he still has a USB 3.0 debugging cable.
>
Should have at the office, I'll pick it up next week and try it out.
-Mathias
next prev parent reply other threads:[~2021-12-03 14:30 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-12-02 15:22 Peter Zijlstra
2021-12-03 0:52 ` Lu Baolu
2021-12-03 14:31 ` Mathias Nyman [this message]
2021-12-03 15:22 ` Dave Hansen
2021-12-03 15:29 ` Greg KH
2021-12-17 11:01 ` Mathias Nyman
2021-12-17 13:55 ` Peter Zijlstra
2021-12-17 15:19 ` Greg KH
2021-12-20 14:40 ` Peter Zijlstra
2021-12-20 15:06 ` Greg KH
2021-12-20 17:01 ` Peter Zijlstra
2021-12-20 14:34 ` Mathias Nyman
2021-12-20 15:51 ` Peter Zijlstra
2021-12-21 9:40 ` Peter Zijlstra
2021-12-21 9:41 ` Peter Zijlstra
2022-01-14 8:47 ` Peter Zijlstra
2022-01-14 19:31 ` Mathias Nyman
2022-01-15 16:06 ` Peter Zijlstra
2022-01-24 14:55 ` Mathias Nyman
2022-01-24 16:39 ` Peter Zijlstra
2022-01-24 16:46 ` Peter Zijlstra
2022-01-25 8:51 ` Mathias Nyman
2022-01-25 10:47 ` Peter Zijlstra
2022-01-25 10:54 ` Peter Zijlstra
2022-01-25 12:45 ` Peter Zijlstra
2022-01-25 13:09 ` Sven Schnelle
2022-01-25 13:54 ` Peter Zijlstra
2022-01-25 14:01 ` Sven Schnelle
2022-01-25 17:13 ` Mathias Nyman
2022-01-25 16:24 ` Dave Hansen
2022-02-17 3:44 ` Randy Dunlap
2022-01-25 19:39 ` Rajaram R
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=88f466ff-a065-1e9a-4226-0abe2e71b686@linux.intel.com \
--to=mathias.nyman@linux.intel.com \
--cc=baolu.lu@linux.intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=peterz@infradead.org \
--cc=x86@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome