Re: [PATCH 4/7] ARM: dts: sun8i: h3: Enable AP6212 WiFi on mmc1 on Nanopi M1 Plus

[Philipp Rossak <embed3d@gmail.com>]

Hi,
thanks for the feedback I will rework the patch.
Should I also update the sun8i-h3-bananapi-m2-plus.dts? It uses also the 
AP6212 and it is done in the same way like in this patch.

Am 30.08.2017 um 16:52 schrieb Maxime Ripard:
> Hi,
> 
> On Wed, Aug 30, 2017 at 05:01:07AM +0200, Philipp Rossak wrote:
>> From: Philipp Rossak <embed3d@gmail.com>
>>
>> The WiFi side of the AP6212 WiFi/BT combo module is connected to
>> mmc1. There are also GPIOs for enable and interrupts.
>>
>> Enable WiFi on this board by enabling mmc1 and adding the power
>> sequencing clocks and GPIO, as well as the chip's interrupt line.
>>
>> Signed-off-by: Philipp Rossak <embed3d@gmail.com>
>> ---
>>   arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts | 35 +++++++++++++++++++++++++++
>>   1 file changed, 35 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
>> index b9c6c27..3054308 100644
>> --- a/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
>> +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1-plus.dts
>> @@ -48,6 +48,7 @@
>>   
>>   	aliases {
>>   		ethernet0 = &emac;
>> +		ethernet1 = &ap6212;
>>   	};
>>   
>>   	reg_gmac_3v3: gmac-3v3 {
>> @@ -59,6 +60,14 @@
>>   		enable-active-high;
>>   		gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
>>   	};
>> +
>> +	wifi_pwrseq: wifi_pwrseq {
>> +		compatible = "mmc-pwrseq-simple";
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&wifi_en_npi_m1p>;
> 
> There's no need for pinctrl nodes when the pin is set to a GPIO.
> 
>> +		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
>> +	};
>> +
>>   };
>>   
>>   &ehci1 {
>> @@ -93,6 +102,25 @@
>>   	};
>>   };
>>   
>> +&mmc1 {
>> +	pinctrl-names = "default";
>> +	pinctrl-0 = <&mmc1_pins_a>;
>> +	vmmc-supply = <&reg_vcc3v3>;
>> +	vqmmc-supply = <&reg_vcc3v3>;
> 
> You don't need vqmmc in this case.
> 
>> +	mmc-pwrseq = <&wifi_pwrseq>;
>> +	bus-width = <4>;
>> +	non-removable;
>> +	status = "okay";
>> +
>> +	ap6212: sdio_wifi@1 {
> 
> You're sure you need a label here?
> 
> Thanks!
> Maxime
>