Re: [PATCH V6 3/5] remoteproc: qcom: Split the head and tail of the q5v5-pil rproc reset function

[Sricharan R <sricharan@codeaurora.org>]

Hi Vinod,

Thanks for the review.

On 5/18/2018 5:52 PM, Vinod wrote:
> On 14-05-18, 16:16, Sricharan R wrote:
> 
>> +static int q6v5_reset(struct q6v5 *qproc)
>> +{
>> +	u32 ret;
>> +	int val, i;
>> +
>> +	/* Assert resets, stop core */
>> +	val = readl(qproc->reg_base + QDSP6SS_RESET_REG);
>> +	val |= Q6SS_CORE_ARES | Q6SS_BUS_ARES_ENABLE | Q6SS_STOP_CORE;
>> +	writel(val, qproc->reg_base + QDSP6SS_RESET_REG);
>> +
>> +	/* BHS require xo cbcr to be enabled */
>> +	val = readl(qproc->reg_base + QDSP6SS_XO_CBCR);
>> +	val |= 0x1;
>> +	writel(val, qproc->reg_base + QDSP6SS_XO_CBCR);
> 
> consider adding a updatel macro which does read, update and write for you...
> 

 ok.

>> +
>> +	/* Read CLKOFF bit to go low indicating CLK is enabled */
>> +	ret = readl_poll_timeout(qproc->reg_base + QDSP6SS_XO_CBCR,
>> +				 val, !(val & BIT(31)), 1,
>> +				 HALT_CHECK_MAX_LOOPS);
>> +	if (ret) {
>> +		dev_err(qproc->dev,
>> +			"xo cbcr enabling timed out (rc:%d)\n", ret);
>> +		return ret;
>> +	}
>> +	/* Enable power block headswitch and wait for it to stabilize */
>> +	val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +	val |= QDSP6v56_BHS_ON;
>> +	writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +	val |= readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
> 
> why is this read required
> 

 It was a ditto of what was given in the programming sequence from HW folks.
 yeah, logically the readl does not look needed. Will remove and update.

>> +	udelay(1);
>> +
>> +	/* Put LDO in bypass mode */
>> +	val |= QDSP6v56_LDO_BYP;
>> +	writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +
>> +	/* Deassert QDSP6 compiler memory clamp */
>> +	val = readl(qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +	val &= ~QDSP6v56_CLAMP_QMC_MEM;
>> +	writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +
>> +	/* Deassert memory peripheral sleep and L2 memory standby */
>> +	val |= Q6SS_L2DATA_STBY_N | Q6SS_SLP_RET_N;
>> +	writel(val, qproc->reg_base + QDSP6SS_PWR_CTL_REG);
>> +
>> +	/* Turn on L1, L2, ETB and JU memories 1 at a time */
>> +	val = readl(qproc->reg_base + QDSP6SS_MEM_PWR_CTL);
>> +	for (i = 19; i >= 0; i--) {
> 
> where is the magic number 19 coming from?
> 

 Its the total number of Q6's memory head/foot switch banks. Infact
 the magic was there even before my patch. But will add a Macro to fix it.

Regards,
 Sricharan

-- 
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation