mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Michael Riesch <michael.riesch@wolfvision.net>
To: Quentin Schulz <foss+kernel@0leil.net>
Cc: linus.walleij@linaro.org, heiko@sntech.de,
	linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	linux-rockchip@lists.infradead.org, linux-kernel@vger.kernel.org,
	Quentin Schulz <quentin.schulz@theobroma-systems.com>
Subject: Re: [RFC PATCH 1/1] pinctrl: rockchip: add support for per-pinmux io-domain dependency
Date: Thu, 11 Aug 2022 09:52:41 +0200	[thread overview]
Message-ID: <9b965d86-9b76-77a1-658e-3675c2138414@wolfvision.net> (raw)
In-Reply-To: <20220802095252.2486591-2-foss+kernel@0leil.net>

Hi Quentin,

Thank you for your efforts! This will solve several issues that are
bound to pop up if a board deviates from the Rockchip reference design.
It seems this does not happen very often, though, which would explain
the lack of responses to your initial query... :-/

A few comments inline:

On 8/2/22 11:52, Quentin Schulz wrote:
> From: Quentin Schulz <quentin.schulz@theobroma-systems.com>
> 
> On some Rockchip SoCs, some SoC pins are split in what are called IO
> domains.
> 
> An IO domain is supplied power externally, by regulators from a PMIC for
> example. This external power supply is then used by the IO domain as
> "supply" for the IO pins if they are outputs.
> 
> Each IO domain can configure which voltage the IO pins will be operating
> on (1.8V or 3.3V).

Just for the sake of completeness: 2.5V is possibly as well (at least on
RK356x), right?

> There already exists an IO domain driver for Rockchip SoCs[1]. This
> driver allows to explicit the relationship between the external power

...allows to model explicitly...?

> supplies and IO domains[2]. This makes sure the regulators are enabled
> by the Linux kernel so the IO domains are supplied with power and
> correctly configured as per the supplied voltage.
> This driver is a regulator consumer and does not offer any other
> interface for device dependency.
> 
> However, IO pins belonging to an IO domain need to have this IO domain
> correctly configured before they are being used otherwise they do not
> operate correctly (in our case, a pin configured as output clock was
> oscillating between 0 and 150mV instead of the expected 1V8).
> 
> In order to make this dependency transparent to the consumer of those
> pins and not add Rockchip-specific code to third party drivers (a camera
> driver in our case), it is hooked into the pinctrl driver which is
> Rockchip-specific obviously.

This approach seems reasonable. But just for my understanding: Does this
mean we need to edit e.g. rk3568-pinctrl.dtsi, iterate over all entries,
and add rockchip,iodomains = <&corresponding_io_domain>;?

If not, at which place are the rockchip,iodomains properties inserted?

> [1] drivers/soc/rockchip/io-domain.c
> [2] Documentation/devicetree/bindings/power/rockchip-io-domain.yaml
> 
> Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
> ---
>  drivers/pinctrl/pinctrl-rockchip.c | 19 +++++++++++++++++++
>  drivers/pinctrl/pinctrl-rockchip.h |  1 +
>  2 files changed, 20 insertions(+)
> 
> diff --git a/drivers/pinctrl/pinctrl-rockchip.c b/drivers/pinctrl/pinctrl-rockchip.c
> index 32e41395fc76..c3c2801237b5 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.c
> +++ b/drivers/pinctrl/pinctrl-rockchip.c
> @@ -24,6 +24,8 @@
>  #include <linux/of_address.h>
>  #include <linux/of_device.h>
>  #include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
>  #include <linux/pinctrl/machine.h>
>  #include <linux/pinctrl/pinconf.h>
>  #include <linux/pinctrl/pinctrl.h>
> @@ -2370,6 +2372,12 @@ static int rockchip_pmx_set(struct pinctrl_dev *pctldev, unsigned selector,
>  	dev_dbg(dev, "enable function %s group %s\n",
>  		info->functions[selector].name, info->groups[group].name);
>  
> +	if (info->groups[group].io_domain &&
> +	    !platform_get_drvdata(info->groups[group].io_domain)) {
> +		dev_err(info->dev, "IO domain device is required but not probed yet, deferring...");

Probably this has been left in there for debugging, but should be
removed to avoid spamming dmesg. IIUC this condition could occur several
times.

> +		return -EPROBE_DEFER;
> +	}
> +
>  	/*
>  	 * for each pin in the pin group selected, program the corresponding
>  	 * pin function number in the config register.
> @@ -2663,6 +2671,7 @@ static int rockchip_pinctrl_parse_groups(struct device_node *np,
>  {
>  	struct device *dev = info->dev;
>  	struct rockchip_pin_bank *bank;
> +	struct device_node *node;
>  	int size;
>  	const __be32 *list;
>  	int num;
> @@ -2684,6 +2693,16 @@ static int rockchip_pinctrl_parse_groups(struct device_node *np,
>  	if (!size || size % 4)
>  		return dev_err_probe(dev, -EINVAL, "wrong pins number or pins and configs should be by 4\n");
>  
> +	node = of_parse_phandle(np, "rockchip,io-domains", 0);
> +	if (node) {
> +		grp->io_domain = of_find_device_by_node(node);
> +		of_node_put(node);
> +		if (!grp->io_domain) {
> +			dev_err(info->dev, "couldn't find IO domain device\n");
> +			return -ENODEV;

Again just for my understanding: The property is optional in order to
provide compatibility with older device trees, right?

> +		}
> +	}
> +
>  	grp->npins = size / 4;
>  
>  	grp->pins = devm_kcalloc(dev, grp->npins, sizeof(*grp->pins), GFP_KERNEL);
> diff --git a/drivers/pinctrl/pinctrl-rockchip.h b/drivers/pinctrl/pinctrl-rockchip.h
> index ec46f8815ac9..56bc008eb7df 100644
> --- a/drivers/pinctrl/pinctrl-rockchip.h
> +++ b/drivers/pinctrl/pinctrl-rockchip.h
> @@ -434,6 +434,7 @@ struct rockchip_pin_group {
>  	unsigned int			npins;
>  	unsigned int			*pins;
>  	struct rockchip_pin_config	*data;
> +	struct platform_device		*io_domain;
>  };
>  
>  /**

Looking forward to the v1 of this series, which I'd be happy to test.

Best regards,
Michael

  reply	other threads:[~2022-08-11  7:53 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-02  9:52 [RFC PATCH 0/1] Making Rockchip IO domains dependency from other devices explicit Quentin Schulz
2022-08-02  9:52 ` [RFC PATCH 1/1] pinctrl: rockchip: add support for per-pinmux io-domain dependency Quentin Schulz
2022-08-11  7:52   ` Michael Riesch [this message]
2022-08-11  8:45     ` Quentin Schulz
2022-08-11  9:26       ` Heiko Stübner
2022-08-11 10:21         ` Quentin Schulz
2023-02-15 10:23   ` Sascha Hauer
2023-02-21 12:14     ` Quentin Schulz
2023-02-22 12:05       ` Sascha Hauer
2022-08-22  8:38 ` [RFC PATCH 0/1] Making Rockchip IO domains dependency from other devices explicit Linus Walleij
2022-08-22 23:43   ` Heiko Stübner

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=9b965d86-9b76-77a1-658e-3675c2138414@wolfvision.net \
    --to=michael.riesch@wolfvision.net \
    --cc=foss+kernel@0leil.net \
    --cc=heiko@sntech.de \
    --cc=linus.walleij@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-gpio@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=quentin.schulz@theobroma-systems.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®