mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Richard Jonsson <richard_jonsson@hotmail.com>
To: <hancockrwd@gmail.com>
Cc: lkml <linux-kernel@vger.kernel.org>
Subject: RE: Unable to write dvd+r on 3 systems
Date: Sat, 14 Feb 2009 23:30:18 +0100	[thread overview]
Message-ID: <BAY108-W52F43AD46BC7BE27057F0B9DB90@phx.gbl> (raw)
In-Reply-To: <49973D4B.30802@gmail.com>

[-- Attachment #1: Type: text/plain, Size: 2540 bytes --]




----------------------------------------
> Date: Sat, 14 Feb 2009 15:53:15 -0600
> From: hancockrwd@gmail.com
> To: richard_jonsson@hotmail.com
> CC: linux-kernel@vger.kernel.org
> Subject: Re: Unable to write dvd+r on 3 systems
>
> Richard Jonsson wrote:
>>
>> It seems I am the last person on earth burning dvd's. I have tried on three different systems, using a mix of growisofs, xfburn, brasero and k3b. They all give the same result for their respective system.
>>
>> On system 1 it takes forever to complete the process. The system is completely useless while burning. IO wait is 50% and hardIRQ is 10-20%. If audio is playing at the same time it stutters in a way that it sounds as it's playing slow. Mouse cursor jerks and it takes eons to even open a new terminal.
>>
>> On system 2 growisofs will try for half a minute and then fail with a message in dmesg. The disc isn't even touched. Tried homebuilt kernel.org kernels from 2.6.25 to current git with no difference. See attachment "growisofs_system2.txt". I have been able to burn exactly 1 disc in total, which magically started recording immediately.
>>
>> System 3 burns at decent speed and always reports success, but about half the time only part of the disc is actually burned. It is visible to the eye, and it will not work. Tried at 4x too.
>
> It sounds like you may have multiple problems. System 1 sounds like
> maybe DMA is not being used for some reason, the dmesg output would be
> useful. On System 2 it looks like a write timed out, and system 3 is
> having burn quality problems. System 1 may have a kernel issue that
> should be looked into, but as for the other two, I would tend to suspect
> the quality of the discs you are using. There is a lot of crap media out
> there, and also some burners don't like discs with media codes that they
> don't have preprogrammed burn strategies for.

Thanks for your reply.

System 1 is affected by
http://bugzilla.kernel.org/show_bug.cgi?id=12309
Also, just noticed that it doesn't appear to have udma capability?!
(see attachment).

Regarding system 3, should there not be an error raised or some such?
It appears to complete the process, but halfway through the laser is
cut?

As for the media, I currently use branded discs (tdk), any
recommendations what to shop for?

_________________________________________________________________
Kolla mailen när du är på språng - skaffa Hotmail i mobilen!
http://windowslivemobile.msn.com/BrowserServiceHotmail.aspx?lang=SE-SE

[-- Attachment #2: hdparm_system1.txt --]
[-- Type: text/plain, Size: 1118 bytes --]


/dev/dvd:

 Model=HL-DT-ST DVDRAM GMA-4082N               , FwRev=HQ04    , SerialNo=K0868EK5201         
 Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic }
 RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0
 BuffType=unknown, BuffSize=0kB, MaxMultSect=0
 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 *mdma2 
 AdvancedPM=no
 Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3:  ATA/ATAPI-2,3,4,5

 * signifies the current active mode


ATAPI CD-ROM, with removable media
	Model Number:       HL-DT-ST DVDRAM GMA-4082N               
	Serial Number:      K0868EK5201         
	Firmware Revision:  HQ04    
Standards:
	Likely used CD-ROM ATAPI-1
Configuration:
	DRQ response: 50us.
	Packet size: 12 bytes
Capabilities:
	LBA, IORDY(can be disabled)
	DMA: mdma0 mdma1 *mdma2 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
HW reset results:
	CBLID- below Vih
	Device num = 0

  reply	other threads:[~2009-02-14 22:30 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2009-02-14 18:54 Richard Jonsson
2009-02-14 21:53 ` Robert Hancock
2009-02-14 22:30   ` Richard Jonsson [this message]
2009-02-15  2:16     ` Robert Hancock
2009-02-14 19:14 Richard Jonsson
2009-02-20 17:02 ` Lennart Sorensen
2009-02-22 10:22   ` Richard Jonsson
2009-02-23 14:50     ` Lennart Sorensen

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=BAY108-W52F43AD46BC7BE27057F0B9DB90@phx.gbl \
    --to=richard_jonsson@hotmail.com \
    --cc=hancockrwd@gmail.com \
    --cc=linux-kernel@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®