Re: [PATCH v5 3/4] dt-bindings: net: broadcom-bluetooth: Add pcm config

[Marcel Holtmann <marcel@holtmann.org>]

Hi Abhishek,

> Add documentation for pcm parameters.
> 
> Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
> ---
> 
> Changes in v5: None
> Changes in v4: None
> Changes in v3: None
> Changes in v2: None
> 
> .../bindings/net/broadcom-bluetooth.txt       | 20 +++++++++++-
> include/dt-bindings/bluetooth/brcm.h          | 32 +++++++++++++++++++
> 2 files changed, 51 insertions(+), 1 deletion(-)
> create mode 100644 include/dt-bindings/bluetooth/brcm.h
> 
> diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
> index c749dc297624..a92da31daa79 100644
> --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
> +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
> @@ -29,10 +29,22 @@ Optional properties:
>    - "lpo": external low power 32.768 kHz clock
>  - vbat-supply: phandle to regulator supply for VBAT
>  - vddio-supply: phandle to regulator supply for VDDIO
> -
> + - brcm,bt-sco-routing: PCM, Transport, Codec, I2S
> +                        This value must be set in order for the latter
> +                        properties to take effect.
> + - brcm,bt-pcm-interface-rate: 128KBps, 256KBps, 512KBps, 1024KBps, 2048KBps
> + - brcm,bt-pcm-frame-type: short, long
> + - brcm,bt-pcm-sync-mode: slave, master
> + - brcm,bt-pcm-clock-mode: slave, master
> +
> +See include/dt-bindings/bluetooth/brcm.h for SCO/PCM parameters. The default
> +value for all these values are 0 (except for brcm,bt-sco-routing which requires
> +a value) if you choose to leave it out.
> 
> Example:
> 
> +#include <dt-bindings/bluetooth/brcm.h>
> +
> &uart2 {
>        pinctrl-names = "default";
>        pinctrl-0 = <&uart2_pins>;
> @@ -40,5 +52,11 @@ Example:
>        bluetooth {
>                compatible = "brcm,bcm43438-bt";
>                max-speed = <921600>;
> +
> +               brcm,bt-sco-routing        = <BRCM_SCO_ROUTING_TRANSPORT>;
> +               brcm,bt-pcm-interface-rate = <BRCM_PCM_IF_RATE_512KBPS>;
> +               brcm,bt-pcm-frame-type     = <BRCM_PCM_FRAME_TYPE_SHORT>;
> +               brcm,bt-pcm-sync-mode      = <BRCM_PCM_SYNC_MODE_MASTER>;
> +               brcm,bt-pcm-clock-mode     = <BRCM_PCM_CLOCK_MODE_MASTER>;
>        };

I am not sure this makes this all that much more readable. I would have been fine with using actual integer values with a comment behind it. Especially since in the driver itself we will never compare against the constants, we set whatever the DT gives us.

Anyway, for the names, I like Rob to ack them before applying them.

Regards

Marcel